Suzuki Samurai -Changing Wheel Bearings

Рет қаралды 59,229

Improvised Builds

4 жыл бұрын

Пікірлер: 28

@nicolas6820 3 жыл бұрын

You saved my day man... thanks a lot! Keep it up

@jordan4690 3 жыл бұрын

Thanks for the video, helpful information and was just what I was looking for

@ImprovisedBuilds 3 жыл бұрын

Glad it helped!

@suzysuzuki8865 3 жыл бұрын

You know you can bolt the tire back on after you remove the nuts that hold the drum on and use the tire as leverage to get the drum off, works every time for me

@supersami7748 3 жыл бұрын

Unless there’s an inspection cover like a TLC and some GM axles all dropout units are non C-Clip.

@DanielCarrera 3 жыл бұрын

Thank you very much for the video. I have a question is there a spacer before the bearing?

@woxtraumer 3 жыл бұрын

Tanks man! !!!!!!

@19frito 4 жыл бұрын

Ur the man great video

@ImprovisedBuilds 4 жыл бұрын

Thanks! Hope it helped

@19frito 4 жыл бұрын

Improvised Builds yea that’s exactly how i did it

@jessvandernest2021 3 жыл бұрын

nice job

@ImprovisedBuilds 3 жыл бұрын

Thanks!

@robormiston2841 3 жыл бұрын

Is there a rear bearing seal? I can't find a any videos that show a seal replacement for rear wheel bearings.

@ImprovisedBuilds 3 жыл бұрын

Yep, go to about 5:45 in the video and you can see me pull it out of the axle

@suzysuzuki8865 3 жыл бұрын

You figure it out?

@davidcraft4909 4 жыл бұрын

to get the bearing on do you have to hit it very hard and like beat the hell out of it or does it seem to tap in. I know its a press fit but i personally don't like the idea of hitting something hard with a hammer if you dont have to.

@ImprovisedBuilds 4 жыл бұрын

The bearing wasn't too hard but the retainer was.. they probably had different grade interference fits

@davidcraft4909 4 жыл бұрын

@@ImprovisedBuilds well i just thought about it and im going to wait until i get a press over here. i have to rebuild a whole 3rd member anyway and i for sure need a press for that.

@ImprovisedBuilds 4 жыл бұрын

@@davidcraft4909 I'll have a shop press one day but no room for now so its hammer time lol!

@chriswoods1558 4 жыл бұрын

The easy was to do this without smashing the bearing is to hold the bearing or retainer on a screwdriver and warm it with a hot air gun. Do not warm it so much that you ruin the insides of the bearing. Just needs to be warm to touch and it will slide on with minimal effort. If you want to put your shaft in the freezer, that will help.

@ryancowgill1616 3 жыл бұрын

@@chriswoods1558 I tried putting my shaft in the freezer, but all that did was make it hard to walk

@juanbeltran3634 4 жыл бұрын

Hey man what size of pipe did you use??

@ImprovisedBuilds 4 жыл бұрын

It was 2" schedule 40 pipe

@juanbeltran3634 4 жыл бұрын

Thank you

@oliviarose3852 Жыл бұрын

My samurai is all gunked up with oil all behind the bearings. Other then the bearings could there be another part I need to replace? Anyone have advice or the same problem?

@Mike-gr2ok Жыл бұрын

Ya need new oil seals dude