How To MAKE OLD BATTERIES NEW Again!!! 12v 6v Deep Cycle, Car, Truck, Golf Cart, Semi

Рет қаралды 1,076,698

3 жыл бұрын

Subscribe to our New Channel / mrknowitallguru
and learn to do almost everything DIY!
MAKE OLD BATTERIES NEW AGAIN!!! 12v 6v Deep Cycle, Car, Truck, Golf Cart, Semi
Friends the 120V & 220 VOLTS ARE THE POWER INPUTS FROM YOUR HOUSE POWER SOURCE, THEY ARE NOT THE OUTPUT OF THE WELDERS. Here we show the simplest and cheapest way to make cars, trucks, and golf carts, marine batteries last an eternity. We show you the exact method on how to use DC converter welders for reviving your batteries and having them last a lifetime!
Throw out your WD-40, PB Blaster along with all your Slick 50 because we found the best Lubricant for EVERYTHING tinyurl.com/bdf6a6ky
We Guarantee you will love it.
TOOLS:
Welder for Deep Cycle ONLY 6 Volt & 12V Batteries amzn.to/3yW4ihK or amzn.to/30k7YNg
Use This for all Standard 12-volt Batteries amzn.to/2K1UsWQ
**If the above welder is unavailable, either one of these will work amzn.to/3mqhebK or amzn.to/3sH4COq **
After doing this process use this charger to slowly fully charge the battery
amzn.to/3kmCThX
If you want to change your battery acid use this amzn.to/3DkbM1m
Basic Welding Rod amzn.to/369etSc
Clamps with Cable amzn.to/3zUwh4a
Vise Grips amzn.to/32qli0N
Distilled Water amzn.to/32notpT
______________________________________________________________
United Kingdom Tools:
Welder amzn.to/3lamXiv
______________________________________________________________
Australia Tools:
Welder amzn.to/2Mv5EN2
The small compensation we receive from these amazon links helps to keep our channel
available to you all for FREE!
****Disclaimer****
Due to factors beyond the control of SWEET PROJECT CARS, we cannot guarantee against the improper use or unauthorized modifications of this information. Make sure you check with your manufacturer to make sure this will not affect your factory warranty. SWEET PROJECT CARS assumes no liability for property damage or injury incurred as a result of any of the information contained in these videos. Use this information at your own risk. SWEET PROJECT CARS recommends safe practices when working with tools seen or implied in our video and written content. Due to factors beyond the control of SWEET PROJECT CARS, no information contained on this KZfaq channel shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this content is the sole responsibility of the user and not SWEET PROJECT CARS.

Пікірлер: 2 300

@SweetProjectCars 3 жыл бұрын

****Folks you need to watch the ENTIRE video be for attempting this process**** Hello everyone good to see you again this is one of our most amazing video projects ever. ****Please make sure you watch the ENTIRE video before attempting. You will love the results of this process. If you would like to donate to our channel to help keep us going please go here. **paypal.me/YourSweetProjectCars** Quote of the Day*** I have always believed, and I still believe, that whatever good or bad fortune may come our way we can always give it meaning and transform it into something of value.” hh

@drymoonproperties 3 жыл бұрын

I lived in Sarasota/Bradenton or seven years and absolutely loved it. The heat and humidity didn't bother me actually even had true Floridians ask me how I tolerated the heat so easily but am lucky I guess in some ways because I had to leave the State because of work but now I am older and very sick actually am terminally ill the way I see it God got me out before my illness took over because I can't take the heat anymore especially the humidity interferes with what lung function I do have left. I love this channel you are just awesome I have learned so much yet thought I already knew lots. I sure do appreciate your hard work and have sent several people to your channel. I hope and pray for your continued success!!

@chibuzo7746 3 жыл бұрын

@@drymoonproperties I know it may sound weird, but can i pray for you?

@gregwiles1612 3 жыл бұрын

Does this work for 8volt golf cart battery or do you recommend different welder

@jakejacob9814 3 жыл бұрын

If you only wanted to buy one welder but have both 6 & 12v batteries could you wire 2 6v batteries in series could u treat it then no different then a 12v?

@lebensraume7945 3 жыл бұрын

Can I charge 2 Volt deep cycle alkaline batteries using a similar procedure?

@dejay727272 Жыл бұрын

I just did this today to a 6-year-old battery that was on its way out and Stranded my niece twice. The battery was maintaining 12.3 volts but now it's rocking over 12.7 volts after shock therapy and a load test!!! Thank you sweet project cars

@SweetProjectCars Жыл бұрын

Our pleasure tom! Glad we could help. Thank you for watching and sharing your results, we appreciate it, hope you have a great week. mad Mike the hammer SPC

@hughmurphy5044 Жыл бұрын

What brand welder for 6 volt

@LegendLength Жыл бұрын

"rocking over 12.7 volts" you almost want to pat it "who's a good boy!"

@steveforliberty7801 2 жыл бұрын

I recieved my welder (the red one) a couple days ago. I already saved my car battery. Knowing that this welder is only for regular car lead acids I decided to experiment and tried it on my dead rv 12v deep cycle batteries that have been sitting for 3 years in the elements. Well what do you know, It worked on them too! Sweet.

@SweetProjectCars 2 жыл бұрын

Awesome Steve! Thank you so much for watching and sharing your fantastic results, we really appreciate it, have a great week my friend. mad Mike the hammer SPC

@richardmcavoy6413 2 жыл бұрын

Steve for liberty I just came across this channel and subscribed. What is the make and model of these two welders? I cant find them in the videos. Thanks.

@toddthurston8317 2 жыл бұрын

@@mrlawski1014 in the video description, press the 'read more' and you should get the rest of the welder's description.

@richardmcavoy6413 Жыл бұрын

@@toddthurston8317 Thanks, I'm not always this helpless. Appreciate your help.

@terrydevera5120 Жыл бұрын

What is the output voltage of your welding inverter machine ???

@Ariztid 2 жыл бұрын

Wow! This freaking works!!! Spent all weekend doing this to 6 batteries on my golf cart and it's unreal how much the batteries came to life. It's like I have a brand new golf cart!

@SweetProjectCars 2 жыл бұрын

Glad to hear, DropD! Thank you so much for watching and sharing your fantastic results, we really appreciate it, have a great week my friend. mad Mike the hammer SPC

@williamisner120 Жыл бұрын

What did you use to fully charge the 6 v battery after processing with the welder?

@peckerpeter2078 8 ай бұрын

I would say, definitely have some gloves that are leather and some safety glasses just in case, might as well be in a well ventilated area to bare minimum have a mask on

@Yimmsta 2 ай бұрын

How are those batteries holding up now?

@klogjo Жыл бұрын

I bought the DEKOPRO 160Amp, batteries in the 36volt golf cart charged to about 90% but the batteries in my 48volt cart charged 100%. Very happy person here. Can't thank you enough, Gary O

@SweetProjectCars Жыл бұрын

Glad to hear Gary!! Thank you so much for watching and sharing your stupendous results, hope you have a great week my friend. mad Mike the hammer SPC

@austinneuenswander108 Жыл бұрын

It works. Got a golf cart with battery’s that were 5 years old and weren’t charged for 2 years . Took many hours to do 6 batteries but saved 4 out of six.

@SweetProjectCars Жыл бұрын

Awesome Austin!! That is a big savings for sure!! Thank you so much for watching and sharing your results, we truly appreciate it, have a great week my friend. mad Mike the hammer SPC

@timleng4404 3 жыл бұрын

I am a believer. I have saved 5 batteries already. Yes, it does hold charges.Thank you!

@SweetProjectCars 3 жыл бұрын

Wonderful! Thanks for watching and sharing your great results Tim! Have a fantastic day. mad Mike the hammer SPC

@williamblair1123 3 жыл бұрын

Tim - have you tried this with smaller batteries?

@faisalfaixal2376 2 жыл бұрын

can i use any dc welder

@northwestrockgem9745 2 жыл бұрын

Hey can I try this with something else elif you don't have a welder? I mean I have a big Miller but my 220 extension cord is too short

@wesman7837 2 жыл бұрын

@@faisalfaixal2376 if you can control the voltage, and keep it under 16 volts, 13-14 v being ideal, and you can use anywhere from 30-200 amps if needed to "wake it up".

@razorsharpbt7078 3 жыл бұрын

Julio is a keeper. Mike, this welder will pay for itself after recuperating one battery! I have several flooded 12 volt batteries lying around. Thank you, my friend, for helping us save money! You are truly appreciated!

@SweetProjectCars 3 жыл бұрын

Wow, we really thank you for that comment, it makes all we do worth it when we read comments like yours my friend. And we think we will keep Hoolio around for a while, he's a good guy! Have a great day! mad Mike the hammer SPC

@lh98 3 жыл бұрын

Did you buy the welder and try it? Results?

@joellipperini 2 жыл бұрын

@@SweetProjectCars I ordered the welder you indicated, will the 160amp welder work on a standard 12volt? The 200 amp welder was unavailable at the time I ordered, the only welder I was able to purchase on your list was the red 160 amp.

@paulg444 2 жыл бұрын

When he cuts to the Julio audio clips I just about laughed a lung out through my nose !!!!

@drfunhawaii7933 2 жыл бұрын

@@joellipperini Did the 160amp work for Car Batteries too? or do you need the 200amp? I have both motorcycle and car batteries....wondering if I need 2 welders, or if one of them will work for both?

@tomo4635 3 жыл бұрын

KZfaq Videos I drop everything for: Sweeeet Project, and jcs phycology. Your the best!

@SweetProjectCars 3 жыл бұрын

Thank you very much! We are glad to have you here with us, we truly appreciate it my friend. Have a fantastic day. mad Mike the hammer SPC

@24revealer Жыл бұрын

I spent a weekend reviving 6 batteries after one took my wife to work, but was completely dead and would not bring her home again. I have a 200 Amp Tig Welder I used and it starts at 9 amps. The lowest setting worked for a few of them and only one did I have to turn up over 30 amps. I am pleasantly surprised this worked. Thanks for sharing. I was dreading having to replace the batteries for my diesel pickup.

@SweetProjectCars Жыл бұрын

Glad we could help my friend! Thank you for watching and for sharing your great results, we really appreciate it, hope you have a fantastic week. mad Mike the hammer SPC

@Pantherforlife 3 жыл бұрын

Thankyou for mentioning my name in all your videos. You the best !! love your channel.

@SweetProjectCars 3 жыл бұрын

Any time! LOL, thank you for watching and sharing Julio!! So glad to have you here with us my friend. Have a stupendous day. mad Mike the hammer SPC

@rotfan77 11 ай бұрын

Thanks for the great Info. And thanks to Julio for finding an even less expensive way to save your batteries at about half the cost of the other heavy duty charger. And I love that you can also use it for some welding.

@SweetProjectCars 11 ай бұрын

Our pleasure rotfan77!! That is exactly why we did this update for viewers so they can do this more economical process and have a welder to use as well, it's a "win - win" :) Thank you so much for watching and sharing, hope you have a fantastic weekend my friend. mad Mike the hammer SPC

@Buzzhumma 3 жыл бұрын

Haha i have been mentioning these welders in different youtube channels a lot of late . They are the most robust power supply on the market and cheap as chips . A few channels are going to start re engineering them for different projects including tesla coils and and hho generator. Good work in spreading the word !

@SweetProjectCars 3 жыл бұрын

Thank you for watching and sharing. Have a great day. mad Mike the hammer SPC

@houstonsheltonbees814 3 жыл бұрын

Cool, saw this in the comments of your other battery video. Thanks for sharing the process 👍 hello from Kentucky mountains USA 👍

@SweetProjectCars 3 жыл бұрын

Thanks for watching! Hello Kentucky mountains, glad to have you with us! Happy New Year. mad Mike the hammer SPC

@prooster8413 2 жыл бұрын

Great video, a welder as well as a battery charger, "two birds with one stone" comes to mind, keep up the good work, Paul from the other side of the pond.

@SweetProjectCars 2 жыл бұрын

Glad you liked it Paul! Thanks for watching and sharing, we appreciate it and welcome from across the pond :) Hope you have a fantastic weekend my friend. mad Mike the hammer SPC

@STFOURNARIS 3 жыл бұрын

It worked!! I pulled two one reading .36v and I did 3 five min shock and it bumped it to 10 v but stoped to 7.5v after resting

@SweetProjectCars 3 жыл бұрын

Good deal, glad we could help you! Thanks for sharing. Have a great day. mad Mike the hammer SPC

@andybaker2443 3 жыл бұрын

So, your 12v battery peaks at10v and drops back to 7.5v. What can it be used for now?

@STFOURNARIS 3 жыл бұрын

@Sweet Project Cars Just did another six deep cycle 6v that where dead (.5v) and they are now bubbling like a soda :) on the original cart charger. You truly have something here that not a lot of people know and i learned first hand. i got both of the welders and like you said on the video i used the red on my car battery that used to be 1.4 v and now is at 12.6v with plenty of cranking power and the smaller welder on a utility cart that has 6 6v deep cycle 225 ah batteries that where not charging when i would plug the charger. i noticed after running the shock treatment for only 2 min at 22 on the small welder the charger was able to recognize them and charge them again. After the shock treatment i connected everything back in the Cart and they registered and started charging then a couple min later the charger was showing that they where fully charged, i took it out for a spin and then a minute in and it died on me so i plugged it in for charge again and ones it was showing fully charged i took it out again and this time it run for about 15 min, now i plugged it again and its been charging for about 11 hours and the batteries are bubbling like a soda however its taking a way longer charge and the charger is still showing 2/6 charged which means the batteries just need to cycle. Again I'm very grateful for sharing your findings with all of us and id like to thank you again. By the way i use jumper cables to connect them and also learned a valuable lesson not to crank the power too high or it might fry your battery :) (i actually did fry a car battery from a jeep by cranking it to 200 and battery got really hot and few cells stopped working )

@MsSlayerful 3 жыл бұрын

Definitely trying this asap... this will help the battery situation since we're off grid😉thanks!👍🏻

@SweetProjectCars 3 жыл бұрын

Thank you very much. Have a fantastic day my friend. mad Mike the hammer SPC

@beast11135 3 жыл бұрын

I have to know. Are you like legit off grid were you can't get internet signal from home and you need to go towards the city to get internet connection. Or more like off the grid like solar power and your own batteries?

@lorengordon9626 2 жыл бұрын

Please note that its smart to insure that any ignition source is far away as the fumes are explosive. Great vid. Never knew you could do this though I suspected it might be possible. As a mechanic for 40 years I could have done a lot of good had I known this back when I started. Thankyou !

@SweetProjectCars 2 жыл бұрын

Thank you for watching and sharing Loren! Have a great weekend. mad Mike the hammer SPC

@lancecowen3604 2 жыл бұрын

@@SweetProjectCars hi this is a great video! Just wondering on the welder to you have the negative coming from the positive plug coming from the welder or negative coming from the negative plug since they are reversible?

@temurayoung9585 Жыл бұрын

@Pat Luxor 😂😂😂

@SethMethCS Жыл бұрын

Very true. Don’t clutch onto helpful tips, share them as it makes everyone richer in the long run.

@LegendLength Жыл бұрын

@Pat Luxor Kentucky Fried Fingers they call it in australia

@cornsilksunshiners85 2 жыл бұрын

Well all I can say is thank you for a great hack. I got the "red" 200 amp welder last week and this past weekend I had an old battery sitting in the shop since 2019,,,it had a 2016 battery date. Went through the steps here on the video and when completed I put it on a trickle charger overnight. Came back the next afternoon and did a battery load test ( 3x to make sure I was actually getting a good reading )and it passed , it was Rock solid good. Now to go through the rest of my scrap batteries to see which ones will wake up.....but that one battery that has been revived just covered the cost of this welder. Thanks again for this great hack.

@SweetProjectCars 2 жыл бұрын

Awesome!! Glad we could help. Thank you for watching and sharing your results, we really appreciate it, have a great day my friend. mad Mike the hammer SPC

@thomasbarlow4223 2 жыл бұрын

Hooked Grandpa's old lead-acid golf cart batteries to my Miller Square wave 350 it worked wonderful been riding this golf cart around for weeks I did a 10-mile Loop the other day

@SweetProjectCars 2 жыл бұрын

Sweeeeet, Thomas! Thank you for watching and sharing your awesome results, we really appreciate it, have a fantastic day my friend and enjoy that golf cart. mad Mike the hammer SPC

@WontSeeReplies 2 жыл бұрын

You are a lifesaver. Instead of spending $5-600 on the charger I can use a $200 welder, and have a welder!

@SweetProjectCars 2 жыл бұрын

Absolutely!! Thank you for watching and sharing, have a great week my friend. mad Mike the hammer SPC

@izh6421 3 ай бұрын

Do you still need to charge the battery using a charger or would this process leave your battery fully charged?

@chriskennedy7534 3 жыл бұрын

Nice idea using the dc welder Julio is a keeper 👍 Would be great if you'd actually do a before and after test though

@SweetProjectCars 3 жыл бұрын

Hoolio is a keeper when he shows up or isn't on vacation LOL. Thanks Chris. No need for a before and after, we know it works, try it and you will see it does too. Have a great day. mad Mike the hammer SPC

@jayarnold5727 3 жыл бұрын

Dude,once again you have totally amazed me.keep up the great vids.

@SweetProjectCars 3 жыл бұрын

Glad you like them! Thanks for watching and for your comment Jay! Happy New Year my friend. mad Mike the hammer SPC

@douglasphillips24 2 жыл бұрын

Much thanks. Now I have another use for my Arc welder that's been collecting dust ever since I got my Mig Welder.

@SweetProjectCars 2 жыл бұрын

Glad to help Douglas! Thank you for watching and sharing, have a great day. mad Mike the hammer SPC

@lorenreyes2855 3 жыл бұрын

I've been watching your videos since 2016. I have always been Absolutely Amazed at your great knowledge and experience. Thank you Very Much Sir. Simply The Best!

@SweetProjectCars 3 жыл бұрын

So nice of you Loren! Thank you for watching and for your kind words, makes all we do worth it. Have a great week my friend. mad Mike the hammer SPC

@johnfitbyfaithnet Жыл бұрын

Agreed

@daddski1 2 жыл бұрын

looking at the comments I think i have something that may help. The welder matters. There is a comment below stating they charged and now the battery is backwards with pos and neg reversed. I think this is because they used a welder capable of mig or tig welding aluminum, whether on a wire feed gun attachment, or just through the actual welder. On these welders, in order to do aluminum, the leads are reversed so you would get their issue. so in the end, I think regardless of welder, you must make sure that your positive lead (stick attachment lead), is plugged into the welder on the positive terminal, and the negative or ground be connected to the welder with the negative connection. To do aluminum with a welder that is capable, one wound put positive on negative and the ground would then go to positive. Make sense? So make sure guys n gals... that both at the battery and at the machine the positive is connected to the welding stick lead and the negative is connected to ground or negative....Hope that helped?

@SweetProjectCars 2 жыл бұрын

Our videos are very product/tool specific, we share only what we have tested an know works every time. Thank you for watching and sharing Daddski 1, we appreciate your input. Have a fantastic day my friend. mad Mike the hammer SPC

@steveale0711 Жыл бұрын

The difference between the red and the yellow welder is duty cycle. The voltages and amperages are almost identical but the red one has a larger duty cycle. That means it can run longer at the higher amperage (say 100 amps). So if you really need to wake up a big boy battery (I found this out on an 8d…1400 cold cranking amps) with the yellow one you might time out the duty cycle before getting the full 5 minutes. Hope that helps, I see a lot of questions about it in the comments.

@SweetProjectCars Жыл бұрын

Thank you very much for your input, we really appreciate it my friend, hope you have a great week. mad Mike the hammer SPC

@adame924 Жыл бұрын

So would you want the larger one for a 12V Deep Cycle Group 31 100AH battery? ...or is the lower duty cycle one still fine because even though the reserve capacity is higher the cranking amps available is lower?

@marinoperna Жыл бұрын

what settings did you use for the 8D battery? Still 5 minutes and 10 minutes off

@CHRIS75MASTER Жыл бұрын

What about voltage? no one says anything about it, what volts these stick dc welders output?

@tarakai2 Жыл бұрын

@@CHRIS75MASTER its known as the closed circuit voltage (CCV). For welders this size generally the DV voltage will be between 18-24 volts

@mikegunter7400 9 ай бұрын

I have been using 12v unit adj to recover units for years. I have been reviving batteries forever with non computer chargers. Until this moment, I did not put them together. I am going to try. 2 to 200 amps, with full amp control. With the hf welder, extraction. I dont rich expensive gear. (I don't use cheap Chinese stuff for gold exstraction.) After bringing them up some. I have found a pulse 4 amp charger that seems to restore them to 80 to 90 per capacity. This a fantastic repair. thank mike

@SweetProjectCars 9 ай бұрын

Thank you for watching and sharing, we appreciate the input Mike, have a fantastic weekend my friend. mad Mike

@mikin.6595 3 жыл бұрын

Thank you very much.I can confirm that this method works.I will try to give info how i did it so maybe someone will find it helpfull.My battery is 75Ah 12V one.It worked perfectly for 3 years without any maintenance at all.First i added 100ml of water to have it enough and over all cells for about half of inch.One cell in my battery was bad.I saw no bubling on charging using my welder on 30A.So i cranked it up to 80A.I keep it running for short time till battery temperature started rising up to 35deg (body temp).Then i made a pause till battery colled down completely.Then i did same thing again.This about temperature is IMPORTANT ..... it must be done as i described.I repeated this for about 15 times.Then i turned it back in to my car.It started at half of key turn.I am testing it today and tomorow i will know.....after cold night.....is this permanent solution or i have to repeat all for more times than i did it now.Battery was not capable to start the car before i tried this.Thank you again and Happy New Year!

@SweetProjectCars 3 жыл бұрын

Awesome Miki! Thanks for sharing your results, we appreciate it. Have a great day. mad Mike the hammer SPC

@mikin.6595 3 жыл бұрын

@@SweetProjectCars It didnt restore full capacity....but was in better condition next day.....so i decided to repeat all over again till i see bubling in all cells to be the same.And it happened after many repeats (to avoid over heating - lowest current setting on my welder is 30A).Now it holds as new.

@untipodeapie 3 жыл бұрын

Hello from Argentina!! I love that tip. Will try it with a dead batery that i have and ley You know if it's work and came back from the death. Keep the good work and thanks for all your help to the diyers and afficionates!!

@SweetProjectCars 3 жыл бұрын

Thank you very much! Glad to have you with us from Argentina my friend. Have a great day. mad Mike the hammer SPC

@wellnessforall6663 3 жыл бұрын

Great stuff. I was really looking for this. Thanks for uploading this video.

@SweetProjectCars 3 жыл бұрын

Glad it was helpful! Thanks for watching. Have a great day my friend. mad Mike the hammer SPC

@VworksArt Жыл бұрын

Dude you saved my entire day. Thank you so much for this.

@SweetProjectCars Жыл бұрын

Glad to hear it Vworks! Thank you for watching and sharing, have a fantastic day my friend. mad Mike the hammer SPC

@drewrinker2071 2 жыл бұрын

For anyone that is stressing if their welder is able to do this or not you must have a DC inverter welder do not do this with a regular ac welder. The reason this works is because DC inverter welders send The amount of current to whatever you set it at, it automatically varies the voltage to meet that current demand. Where as a typical battery charger may be rated at 200a jump but what happens is that with all of this calcification it will raise the internal resistance of your battery. Let's say you put it in 200 amp jump mode, but its only outputting 14-16 volts or so by the time you calculate ohms law theoretically even if you're in 200 amp mode that charger will only be delivering only a few amps to your battery until the resistance is lowered by cranking on the starter which will allow the full 200a jump start to do it's job and will only then be able to deliver the 200amps but it goes directly to the starter. Now with the weld welder on the other hand, he doesn't give a crap about your batteries internal resistance. Because if your battery has a high internal resistance guess what? it's going to raise the voltage so that it can send the full amount of current that you set it to this is how it works. On mine I was watching as I was restoring my battery and in the beginning the voltage was as high as 66 volts and I was worried but this is how it works to break that crap up because in the beginning your battery has a very high resistance whereas a normal 200 amp battery charger starter wouldn't be able to save your battery this will

@SweetProjectCars Жыл бұрын

Thank you for watching and sharing Drew, have a great day. mad Mike the hammer SPC

@danielweir81 2 жыл бұрын

Awesome, i have all the stuff and a few very needed battery's to re boot. Thank you so much for the knowledge as im exited not to have to save up to get things going again 👊😉

@SweetProjectCars 2 жыл бұрын

Glad we could help daniel! Thank you so much for watching and sharing, we appreciate it. Have a great day my friend. mad Mike the hammer SPC

@gregovolsung8769 3 жыл бұрын

Wow that's awesome to use that welder. I just gave you a thumbs up at 4.4k likes that you have. Thanks for the info. I will get one of those welders as I also always wanted to do some welding. Great to have you here in America you are one of the reasons it is getting gerat again. ;)

@SweetProjectCars 3 жыл бұрын

Thanks 👍 Glad it was helpful! Hope you have a fantastic day, thanks for being here with us. mad Mike the hammer SPC

@cantweallgetalong 5 ай бұрын

Oh man, I just bought a new interstate battery from Costco and gave them my old one that had a 42 Month warranty instead of a 36 Month on the new one. Dang! But i was impressed that I got 48 Months on the 42 Month battery before it got weak and sulfated. I almost feel like going back to Costco and getting the old one back and giving the rejuvenation treatment a try.

@Adub408 3 жыл бұрын

I did the baking soda method and revived 2 out of 5 of the old batteries I had. I called it a success. Using the high powered welder to charge the battery instead of the normal trickle charger is genius. Thus taking away the need to use the baking soda to activate it.

@SweetProjectCars 3 жыл бұрын

No baking soda required, not necessary. Thanks for your comment. Have a great day. mad Mike the hammer SPC

@markmcconnell8705 2 жыл бұрын

Baking soda neutralizes sulfuric acid. In other words, it would take the electro out of electrolyte. Haha I don't see how baking soda could activate a lead acid battery. I have used water and baking soda to clean out an old battery.Kept flushing it until it no longer bubbled. Then thoroughly flushed out the battery with clean water. Should use distilled the last few times before refilling it. Charged it it for 24 hours on 2 amp and it worked for, well I don't know. I moved away 2 1/2 years later.

@stoatrepublic 2 жыл бұрын

@@markmcconnell8705 Does that mean the heavy lead acid battery is then lyter?, lol.

@wellnesspathforme6236 Жыл бұрын

@@markmcconnell8705 Did you have at least one dead cell before you cleaned out the battery and refilled it?

@carlfalk7251 Жыл бұрын

@@markmcconnell8705 Exactly. Battery killer.

@harryvanhoo7235 Жыл бұрын

Hi Sweet Project Cars, just come here from the link you sent me from the other video, thank you for that. Trying my stick welder. The lead that would be attached to the body of the work, has a red rubber cover on the clip. I did put this on to the positive terminal. I noticed that your machine has a black handle on that part and you put it on the negative terminal. This would have been my intuitive way also. It is a very old battery and still have three other better one's to try. Anyway, it started bubbling, 2 at first, then up to 5. The battery got fairly hot. It is in a very breezy part of the carport. When it cools down, I might try the other polarity, and stand well clear, which I do anyway. It went from 4.3 v to 3.8 v. This is fun but I do take precautions seriously. Cheers.

@SweetProjectCars Жыл бұрын

Harry, this video shows specific welders that we use and only recommend, please follow the video to a T, there is no other alternative, use the exact same tools, products and method, we've spent years perfecting this process. It works flawlessly every single time using either of these welders for standard battery amzn.to/2K1UsWQ or deep cycle amzn.to/3yW4ihK Thanks for watching, have a great day. mad Mike the hammer SPC

@Superado2006 3 жыл бұрын

Thanks for the video, I got them both. What settings do I use for 12V RV/marine deep cycle batteries?

@SweetProjectCars 3 жыл бұрын

Start at the lowest, and work your way up as shown in the video. Follow the video to a T. Thanks. mad Mike the hammer SPC

@knowjuan3702 3 жыл бұрын

Tnx for sharing sir. Battery companies wouldn't like that 🤣🤣🤣

@SweetProjectCars 3 жыл бұрын

you are very right

@ssoffshore5111 2 жыл бұрын

Okay, I bought a 200A DC inverter welder yesterday since the original battery in my 2015 TDi gave up the ghost in the cold weather. Rather than spend $200+ on another battery, I figured I'd buy a tool and at least try to revive this thing, plus the two 9 y/o batteries in my Cummins are about done as well. I topped off the level in the TDi battery and zapped it 4 times last night (it cooled off quick in the cold weather). When I was done the battery was at 12.92V. The car fired right up. This AM it also fired right up (20°F). We'll see how long this "fix" last for. I'll zap the truck batteries in the Spring when I need the truck again. BTW, the electrolyte looked completely brown clay colored when done. If this holds out until Spring, I'll flush and put fresh electrolyte in it... it was nasty looking! Reply later if anyone wants a future update on how it worked out longer term.

@SweetProjectCars 2 жыл бұрын

Great to hear SS! Thank you for watching and sharing, we really appreciate it, have a fantastic day my friend. mad Mike the hammer SPC

@ssoffshore5111 2 жыл бұрын

@@SweetProjectCars Well sadly I woke up to a very weak battery, by the time I went to leave for work today, it wouldn't start the car. Napa is now the proud owner of the TDi battery...

@rrivera2034 Жыл бұрын

Thank you Mike! Interesting video update, and 1 question: could one use the 160 amp machine to do the big 12v battery's? I notice you never really cranked the gain on the 200amp except momentarily for demonstration, I have a 160 amp machine and I'm wondering. Thanks in advance!

@SweetProjectCars Жыл бұрын

Please follow the video to a T, there is no other alternative, use the exact same tools, products and method, we've spent years perfecting this process and we know that it is safe for both you and your batteries. Thanks for watching and asking, have a great week Rick. mad Mike the hammer SPC

@scotthall9799 2 жыл бұрын

Hey Mad Mike, Thanks for the great video! KZfaq is awesome for sharing knowledge for all us DIYers. My wife says I need to take a break from my addiction to it. But seriously, I have a half dozen golf cart batteries and slew of other batteries I never returned for cores over the years and if I can save them I may be able to treat her to a date night or two. Happy wife, happy life! So my question is, what makes one welder suitable for the deep cycle batteries and not standard batteries and vice versa? Do they operate differently or is it amperage or adjust ability? Thanks!

@SweetProjectCars 2 жыл бұрын

Well Scott, we like to take the guess work out for our viewers, we've tried and tested many, many different welders over the years on the different style batteries and our recommendations are what we know without a doubt work, and work every time and are safe for both you and your batteries. Thank you for watching and sharing, we truly appreciate our great subscribers like you, hope you have a fantastic day my friend. mad Mike the hammer SPC

@southernacho Жыл бұрын

Thanks a lot for the tip, works great on my BMW motorcycle battery, I saved around $300 dolars at least, the price varying about quality brand. Awesome 😎✌️

@SweetProjectCars Жыл бұрын

Nice work! Thank you so much for watching and sharing your results, we really appreciate it Southernacho! Hope you have a great day my friend. mad Mike the hammer SPC

@valtersvidauskis3781 2 жыл бұрын

It works for me. I used inventor stick welder. Its amazing! Thank you!

@SweetProjectCars 2 жыл бұрын

Great to hear Valters, glad it worked! Thank you for watching and sharing, we really appreciate it, have a fantastic day my friend. mad Mike the hammer SPC

@Kungfupanda839 3 жыл бұрын

Thanks for the tutorial. I'm going to try it since I've a arc welder lying around

@SweetProjectCars 3 жыл бұрын

Thank you for watching and sharing. Have a great day. mad Mike the hammer SPC

@joesmith-dk3uz 3 жыл бұрын

I'm not sure any old arc welder will do, it must be a DC welder, and I think the success of the inverter welder is it keeps things a little safer. the circuitry of an inverter welder will turn off on a dead short but it won't do that on a transformer welder, even if it is a DC version.

@Kungfupanda839 3 жыл бұрын

@@joesmith-dk3uz mine is inverter welder. I'll keep u update once I try it on my battery. Thank you for the reminder. 👍

@Kungfupanda839 3 жыл бұрын

@@joesmith-dk3uz I managed to revived my 6 years old motorcycle 12V lead acid battery.

@erikmiller2514 3 жыл бұрын

Genius! Thanks for the tip!

@SweetProjectCars 3 жыл бұрын

Happy to help! Thanks so much for watching Erik! Have a great day my friend. mad Mike the hammer SPC

@whenindavao 2 жыл бұрын

i tried this on my first battery. and yes, it works!

@SweetProjectCars 2 жыл бұрын

Excellent! Thank you for watching and sharing your great results Jonathan, we really appreciate it. Have a fantastic week my friend. mad Mike the hammer SPC

@josemedeiros007 5 ай бұрын

Good job making the video, it was very informative. What is your opinion on battery desulfators? I use a Pulse Tech PowerPulse passive desulfator, they claim to have a patented frequency they use to desulfate batteries, I have been using it on my BMW battery for the past three years and never have any issue's starting even though I only drive about 25 miles per week.

@briancclevenger 3 жыл бұрын

Thank you for the great video. I tried your process and was able to get all the cells the boil except for the two ends. Any suggestions?

@SweetProjectCars 3 жыл бұрын

With this method, if you can't get all the cells to boil then the battery is un-repairable. Thank you for watching and asking. Have a great day Brian. mad Mike the hammer SPC

@SpoonerTuner 3 жыл бұрын

This process is called "Equalizing" the battery and is standard maintenance process used on led-acid batteries. Most of the time they will put a constant voltage Equalizing charge on it of 15v-16.5v for about an hour depending on the temperatures. At lower temps you can do it at higher voltages. What you're doing is basically the same thing but for a much shorter period of time and using higher voltages. Its actually a really great idea in my opinion because sometimes even at 16.5 volts you still can't push the current through the sulfated layer on the plates. They recommend to do this once every 1-3 months to keep them fresh on batteries that aren't used very often. If it's an AGM battery you need to be more careful to not overheat it. Thanks for the great video.

@SweetProjectCars 3 жыл бұрын

Our pleasure. Thanks for sharing! Have a great day. mad Mike the hammer SPC

@sukmidri 3 жыл бұрын

Yep,did this when I was in charge of maintaining forklift batteries. Had industrial chargers that could equalize,wanted to say they did around 205 amps for equalizing,was years ago.

@kobusvaneden690 2 жыл бұрын

Is it amps or voltage on that welder's lcd-display? How much voltage does the welder put in that battery? If I understand your comment correctly, 16.5 Volt 8s a maximum. But the welder does 200 Volt, does'nt it?

@jsparlin1 2 жыл бұрын

just did a small 12 v..had 1.5 showing.. started charging, nearly nothing, but a little..cranked all the way up on welder, not much, but increasing..got better, but battery charger would't charge.. kept working with it and suddenly steam started shooting out of vents.. turned down..soon couldn't put welder on battery.. then charger would tAKE over. to my amazement, it worked. gratis

@SweetProjectCars 2 жыл бұрын

Awesome James! Thank you for watching and sharing your results, we really appreciate it, have a fantastic day my friend. mad Mike the hammer SPC

@theroyalcrownedtiger2946 3 жыл бұрын

Thank You, much likes from Canada !

@SweetProjectCars 3 жыл бұрын

Thank you very much, we appreciate your view and comment my friend. Have a great day. mad Mike the hammer SPC

@tlbx57 Жыл бұрын

I would suggest a simple voltage check with a meter before and after the process and a simple battery stress test as well. Those would affirm the process.

@SweetProjectCars Жыл бұрын

Well Tony, do as you wish, but we don't need to affirm anything to anyone because we've been doing this process for years and years and years and we know it works when done as shown and works every time. Thanks for watching. mad Mike the hammer SPC

@HotMannaMinute 4 ай бұрын

I got a question, can i use any electronic welder??? I got the cheap one from harbor freight will that work???

@h8GW 8 ай бұрын

Good advice for those who already have a DC welder.......but I still would use a face shield when looking down into the fill holes...

@SweetProjectCars 8 ай бұрын

Any time you work on your vehicle there are obvious safety precautions, you don't want to hover over the cells and look in them while you are doing the process. Thanks for watching, have a great day. mad Mike

@semco72057 2 жыл бұрын

That looks like a nice procedure and I will try it on some batteries I have to do something with as I am tired of buying batteries for my vehicles and mowers.

@SweetProjectCars 2 жыл бұрын

Thank you for watching and sharing Sidney, have a great weekend and all the best on your project. mad Mike the hammer SPC

@happyhomelesshomesteaders158 3 жыл бұрын

Great video thanks for the advice 🌹🌹

@SweetProjectCars 3 жыл бұрын

Glad it was helpful! Have a great day, thanks for watching. mad Mike the hammer SPC

@williammaldonado3516 2 жыл бұрын

Thanks "Julio"

@SweetProjectCars 2 жыл бұрын

Absolutely! We will pass that along William, thanks for watching. mad Mike the hammer SPC

@dannytarboush6696 3 ай бұрын

Thank you for the video, can I apply the same method to revive 8 volt golf cart batteries?

@tommycoates1978 Жыл бұрын

Ordered my inverter welder today. Have bought pulse Tex maintainer which has been in place a couple years now. Not seen any real world improvement with it. Bought two more desulfator chargers with near endless hours ran on deep cycle batteries with very little improvement. This method looks promising but still up in the air about it. At I will have small stick welder that can be used portablely with genny. I’ll try this a couple times and if no improvement I will change out the electrolyte after boiling a couple times in distilled water. Also get specific gravity readings through out servicing. Thx for video

@SweetProjectCars Жыл бұрын

Happy to help Tommy! Thank you for watching and sharing, have a great day and all the best on your project my friend. mad Mike the hammer SPC

@virgilkirschner5717 2 жыл бұрын

Would be great if you could do a load testing of the battery before and after. Thank you love your show.

@SweetProjectCars Жыл бұрын

We leave that to our viewers, we aren't out to prove anything, we share this because we know it works. Thanks for watching, we appreciate it, have a great day. mad Mike the hammer SPC

@314159265135 2 жыл бұрын

I ordered the welder last week from Amazon and restored my battery today. I had one hole that was a little stubborn to bubble but after cranking up the power, it was resurrected. Thank you for the video good sir!

@SweetProjectCars 2 жыл бұрын

Awesome, Aaron! Thank you so much for watching and sharing your results, great job my friend! Hope you have a fantastic day. mad Mike the hammer SPC

@StephaneGuayMCB 2 жыл бұрын

Can you post the link from Amazon please ?

@suzannetisseur2872 Жыл бұрын

Did this with 3 × 12 volt deep cycle batteries over a 3 day period. The batteries are 5 year old maintenance-free batteries that my friend had in a golf cart that he sold me last year. The cart would move extremely slowly prior to removal from the cart. After charging, the batteries barely made it above 12 volts and wouldn't maintain the voltage, then returned back to the 11.7 avg. thing that I did was to steam clean the exterior of the batteries with dish soap to remove dirt, grease, and any acid residue. Next, remove the labels covering the screw down caps, and with the caps off, I hooked up a regular charger for fun to see if there were any signs of charging bubbles, but even after an hour, no signs of anything positive happening, until I hooked up the DC inverter welder and I was in a totally different universe where I'm now in control of my batteries destiny thanks to Sweet Project Cars. After working on the batteries on and off for a couple of days, the SOH (STATE OF HEALTH) went from 65-70% to 90% on all 3, and the SOC (STATE OF CHARGE) went from 60-65% to a consistent 97-100%. The only question that I have is that the electrolyte in the cells is extremely dirty. it's obviously the sulfate that has been dislodged from the plates, would it be worth the effort in trying to filter out the crap that's in the electrolytes, and if I did, can I assume better battery longevity and performance? Thanks again!

@SweetProjectCars Жыл бұрын

Anytime you clean something up it works better my friend, if you have the time it doesn't hurt to re-condition the things you care about. Thank you for watching and sharing your results, we really appreciate it, hope you have a fantastic week. mad Mike the hammer SPC

@stevofromiowa 11 ай бұрын

There's another post in this thread from a couple of years back that talks about it. His recommendation at the time was to drain and replace the acid. IDK if it would improve life or not, but it surely couldn't hurt?

@fvrrljr Жыл бұрын

Eso Es Todo Mi Julio aka That's What I'm Talkin 'Bout Hoolio 🎶Goodbye to Rosie, the queen of Corona Seein' me and Julio Down by the schoolyard 🎶 🎶Seein' me and Julio Down by the schoolyard🎶

@SweetProjectCars Жыл бұрын

You got it! Thank you for watching and singing us Hoolio's favorite toon :) Have a fantastic day my friend. mad Mike the hammer SPC

@rchyn2089 3 жыл бұрын

thanks for the tip, mike... i tried on my car 2 years old battery, because it was hesitant to start in the morning, using arc 160 dc welder, and it worked... been 3 days now.. just for info, i measured the charging voltage, it was 15.6 volts, on the lowest amps setting. i used the schedule of 3 minutes on - 5 minutes off, 6 times, because i was cautious of the boiling acid, and the battery was very hot to touch.

@SweetProjectCars 3 жыл бұрын

Thank you for watching and sharing, we truly appreciate it my friend. Have a fantastic weekend. mad Mike the hammer SPC

@jeremytome 3 жыл бұрын

This is one of the most innovative channels out there.

@SweetProjectCars 3 жыл бұрын

Thank you Jeremy! We appreciate all of our great subscribers like you. Have a fantastic day my friend. mad Mike the hammer SPC

@ObamaoZedong 2 жыл бұрын

Always wanted a welder. This is my excuse to buy one!

@SweetProjectCars 2 жыл бұрын

Absolutely! Thank you so much for watching and sharing, we truly appreciate it. Have a great day my friend. mad Mike the hammer SPC

@derwinokeynan7215 3 жыл бұрын

Thank you for this tip!

@SweetProjectCars 3 жыл бұрын

You're so welcome! Thank you for watching and sharing, we truly appreciate it Derwin. Hope you have a great weekend. mad Mike the hammer SPC

@ronpotts6715 3 жыл бұрын

Looks like the welder I have , is the red welder a sungoldpower 200A lift tig , were you using it on 110 or 220

@SweetProjectCars 3 жыл бұрын

It doesn't matter which you use, but we use it on 110 which is standard house voltage. Thanks for watching and asking. Have a great day. mad Mike the hammer SPC

@JohnVeitch1 3 жыл бұрын

Purchased the YESWELDER that you have in the link for deep cycles. Turning it on the first time it worked fined and got good bubbling for 5 minutes turned it off and waited 10 minutes but that was it, cannot get any bubbling to happen after that no matter what I do with the welder, checked the connections and they are fine. Used a multimeter to see if any voltage was going into the battery when turning on the welder and it would jump up to 18 volts and then drop down to the batteries 12 volt.

@SweetProjectCars 3 жыл бұрын

Try it on another battery to test and make sure the welder is working correctly. That's what we do. Thank you for watching and asking. mad Mike the hammer SPC

@51hankyspanky7 2 жыл бұрын

Does anyone else think it is actually Adam Carolla making this video? 😁

@SweetProjectCars Жыл бұрын

LOL, I've heard that before :) Thanks for watching, hope you have a great week my friend. mad Mike the hammer SPC

@N3ttwerk 2 жыл бұрын

This saves so much F'ing money man...

@SweetProjectCars 2 жыл бұрын

Absolutely, it does, James! Thank you for watching and sharing, have a great day my friend. mad Mike the hammer SPC

@speedfreak1161 3 жыл бұрын

🤔WOW will be trying that next time 💪😁🇦🇺

@SweetProjectCars 3 жыл бұрын

Thanks Speed Freak! Have a great day. mad Mike the hammer SPC

@swampcabbage3239 3 жыл бұрын

Dude Julio’s gonna survive any ish that ever happens ... dudes a badass🙌🏻

@SweetProjectCars 3 жыл бұрын

Hoolio is our mad, mad scientist :) He will survive! LOL Thanks for watching. Have a great day. mad Mike the hammer SPC

@ShaftmanOld7 3 жыл бұрын

Thank you for the information!

@SweetProjectCars 3 жыл бұрын

Our pleasure! Thanks for watching. Happy New Year. mad Mike the hammer SPC

@alimcanuff6056 2 жыл бұрын

Very nice helpful video bro keep up the good job . Blessings bro

@SweetProjectCars 2 жыл бұрын

Glad we could help Ali! Thank you so much for watching and for your comment, we truly appreciate it, have a blessed week my friend. mad Mike the hammer SPC

@2841orlando 3 жыл бұрын

I gotta thanks Julio for this idea

@SweetProjectCars 3 жыл бұрын

He's our mad scientist! Thanks for watching. Have a fantastic day. mad Mike the hammer SPC

@samuelatanuku4755 2 жыл бұрын

Thank YOU

@SouthernMaineRemodel 3 жыл бұрын

Got the latest grey Amico welder (which is a nice little welder for sure) that was recommended took an old ancient Legend battery out of my friends barn which was totally dead and sitting on the bare ground for a long time in a frigid climate, hooked it up and turned the knob till it started boiling (about 90 amps or so) I followed the procedure to a "T" and after cooling I charged with a NAPA 2 amp trickle charge for 24 hours it did bring the battery up to the spot right between "replace" and "good" on the NAPA charge gauge and I tried it quick on my 16 HP JD mower which it easily started again and again with no trouble.....I was wondering if Julio ever recommends doing the procedure twice or if there is any detriment to doing it twice if one winds up with a marginal result. Oh BTW a couple things I noticed was if you try a battery and it won't boil regardless of how hard you hit it including (200 amps) its toast take it to the junk yard as the physical electrical pathway internally has been compromised somehow also I had trouble with the battery boiling over as it became warmer about (125 degrees) this was easily corrected with my wife's turkey baster by extracting a little bit (she'll never miss it) LOL .......Julio what do you think? 2nd time around with the procedure? also I ordered the battery charger recommended but still waiting for it . I will follow up with how this works

@SweetProjectCars 3 жыл бұрын

Thank you so much for watching and for sharing your results Darrell! Hope you have a great day. mad Mike the hammer SPC

@queenstownkid 3 жыл бұрын

yea you can do it more then once

@freethinka69 3 жыл бұрын

Thank you for the video. I noticed the link for the Australian availability trade right welder is 180 amp, will this serve both battery types as it is inbetween 160amp for deep cell and 200 amp for 12 volt regular batteries? Would 180 amp be ample for regular 12 volt batteries. Thank you in advance

@SweetProjectCars 3 жыл бұрын

Australia has very limited tools to them, you can try this welder, it works on many wet-style batteries. Thanks for watching. mad Mike the hammer SPC

@intelligentdesign9911 3 жыл бұрын

Brilliant,,, Again!

@SweetProjectCars 3 жыл бұрын

Thank you very much, it's our pleasure to help. Hope you have a fantastic day. mad Mike the hammer SPC

@meyawabdulaziz3863 Жыл бұрын

battery factories watching this video : boss.....we are officially screwed

@SweetProjectCars Жыл бұрын

LOL, thanks for watching and commenting, have a great day my friend. mad Mike the hammer SPC

@davidallton8074 2 жыл бұрын

Looking at the spec of the UK welder you have kindly provided, the welder operates at around 27 V, could a 24 V charger be used in place of the welder?

@SweetProjectCars 2 жыл бұрын

Give it a shot David, if it doesn't work for you, you know what you have to do. Thanks for watching, have a great day. mad Mike the hammer SPC

@carpediemarts705 2 жыл бұрын

Stick welders are constant current (amps) power sources. Turn the dial to one amperage and it will put out exactly that amperage. When welding, the voltage will change to whatever is needed for the spark to jump the gap between the electrode stick and the work metal. Normally in a battery, the gap between the plates either requires 2 volts to charge, or produces 2 volts. Battery chargers are often sold in 2 amp, 6 amp, 12 amp models, and a few large ones only sold to garages around 80 amps. A typical stick welder runs at 120 amps for a 1/8" welding rod. So what these welders are doing is brute force charging and boiling the water underneath the sulfur scales coating the lead plates and breaking them off allowing the water in the cells to finally touch the plates.

@carpediemarts705 2 жыл бұрын

So David Alton was asking about using a 24 volt charger instead of a welder with 27 volts peak capacity. Just because his listed welder says 27v doesn't mean it is putting out 27v. If when welding, you pull your electrode away from the workpiece too far, the machine will increase the voltage to 27, and when your electrode is too far away for that to jump the gap, the machine shuts off. If a battery is 12v, and you attach a 24v charger to it, it may or may not do anything different than a 12v charger. Depends in the amperage setting you turn the charger into. Using 24v to charge a 12v battery won't do anything special.

@seankettle6873 2 жыл бұрын

Amazing! I can't source the DEKOPRO welder in the UK - will other equivalent welders do the job? I have found a few 160A IGBT units, or does it have to be the specific DEKOPRO?

@SweetProjectCars 2 жыл бұрын

We recommend this amzn.to/3lamXiv for our UK viewers Sean. And remember, all of the products/tools we use in our videos can always be found in the SHOW MORE of the videos description, if you can't find it let us know and we will help you. Thanks for watching. mad Mike the hammer SPC

@Z71__ Жыл бұрын

Julio, you have proved me wrong again. I revived a dead battery with this process. Now I just need to see how long it holds up. Thanks!

@SweetProjectCars Жыл бұрын

Glad to hear Z71! Thank you for watching and sharing your results, have a great day my friend. mad Mike the hammer SPC

@krisbrost676 2 жыл бұрын

Will the cheaper wielder (Deckpro 160 Amp) work with 8V golf cart batteries? Love this video and hoping to make it work with my (6) 8 volt golf cart batteries…that would make my day! Thank you Sweet Project Cars for the time and effort you put into the video and all of your comments. 🙏🏼👍🏼💪🏼

@SweetProjectCars 10 ай бұрын

Yes it will Kris! Just cut all timelines in half for that size battery, sorry for the delay in responding my friend, hope you have a fantastic day. mad Mike

@richardabner9420 3 жыл бұрын

Thank you for the SWEEEEET and awesome videos!!!! 😃😃😃😃

@SweetProjectCars 3 жыл бұрын

Glad you like them! Thanks for being here with us! Have a great day. mad Mike the hammer SpC

@Rexag 2 жыл бұрын

This is a great video, and I am a DIY guy. For me, sometimes it is just time vs money and the opportunity cost at which I will decide if it is worth it. Don't get me wrong, this is a great way to beat the system, but I will just replace it. Thanks for the video.... who knows when I might just do it.

@SweetProjectCars 2 жыл бұрын

And remember, you can do this for friends, family, neighbors, co-workers etc, so you have multiple options to help others as well to save $. Thank you for watching and sharing Rex, have a fantastic weekend. mad Mike the hammer SPC

@laszloiso777 3 жыл бұрын

Mike my man! I have them both... welder and dead battery... First I'll try it with a really old one... if it works I open a battery repair shop :D !!!! And I'll donate some of my savings! THX!

@laszloiso777 3 жыл бұрын

Big respect from Hungary!

@SweetProjectCars 3 жыл бұрын

Follow the video to a T my friend. We are here for you, if you need help, reach out with any questions. Thank you for watching and for your kind words. Have a fantastic day. mad Mike the hammer SPC

@laszloiso777 3 жыл бұрын

@@SweetProjectCars Nice thank you! I eventually skipped the project today because of heavy frost... I think it will work better at least around +15 C... And since you are so nice I dare to ask: Is it not better to fill in battery acid instead of distilled water? ?? I have them both... and I just wonder, maybe the old battery would require some fresh acid... And is the polarity important where to connect wich cable?? Thank you for the answers. Ps : be careful with the 303 rubber treater I read it can cause harm to the human body.. possibly carcinogen! Just take extra care... It looks really effective, however! Keep on the good work! Respect!

@MIKEYSREVIEWS 3 жыл бұрын

I have to say this video is very interesting.

@SweetProjectCars 3 жыл бұрын

Glad you think so! Thanks for watching. Have a great day. mad Mike the hammer SPC

@duydinhnguyen6225 3 жыл бұрын

Old men we love yo , thanks for the tip 😎💪💪 ya to deadly.

@SweetProjectCars 3 жыл бұрын

Thank you very much! Glad to have you here with us, we appreciate it. Have a great day. mad Mike the hammer SPC

@michaelwright1602 Жыл бұрын

I'm pissed! I just replaced 4 group 31 batteries just the other day! It would have been much cheaper to have simply bought the stick welder. Now I know, thank you for the video, this will not happen again.

@SweetProjectCars Жыл бұрын

Agreed, now you know for the next time Michael! Thank you for watching and commenting, have a great week my friend. mad Mike the hammer SPC

@Keazyjuan 3 жыл бұрын

Love it!!!!

@SweetProjectCars 3 жыл бұрын

Thank you for watching! Glad to have you with us. Have a great day. mad Mike the hammer SPC

@czeslawrogalski1837 3 жыл бұрын

👍👍👍good job

@SweetProjectCars 3 жыл бұрын

Thank you! Cheers! Glad to help, have a great day. mad Mike the hammer SPC

@holidayrap 3 жыл бұрын

I know next to nothing about welding. Bought a "Stark AC welder" a few years ago did not use it at all. Pulled it out and tried this method with 70amps. Thought I did something wrong. I heard a pop and the clamp that I used (may be it was too thin) burned off. But I tested the battery and WOWW!!! its up to 800 plus cranking amps! Thats from a max of 250 CAs after several attempts to charge it after using your previous "bubbling method". Mad Mike big props...this freaking works!

@SweetProjectCars 3 жыл бұрын

Good deal, glad it worked, surprised you got it to work with AC voltage, are you sure it wasn't on DC voltage? Thanks so much glad we could help. mad Mike the hammer SPC

@donaldtrumpjr 2 жыл бұрын

hi Sweet Project Cars. Thank you for the videos. I noticed the welder you recommended for the 6 volt deep cycle charging is no longer available. Could you elaborate on what characteristics would make a good welder choice, or help provide an alternate option? thank you!

@SweetProjectCars 2 жыл бұрын

This amzn.to/3svkTG1 is the one in the SHOW MORE and the one we use and recommend. Thanks for watching Doland. mad Mike the hammer SPC

@matthewb2060 2 жыл бұрын

@@SweetProjectCars I was wanting this question answered as well. Your link takes me to a can of spray lubricant on Amazon.

@danielbrothers Жыл бұрын

@@matthewb2060 Yes sir... it still shows the lub....not the welder

@diypapie8428 Жыл бұрын

Good too know these are DC welders ... Gonna try it

@SweetProjectCars Жыл бұрын

Awesome! Thanks for watching and sharing, have a great week my friend. mad Mike the hammer SPC

@tanyaholmes3213 3 жыл бұрын

I'm amazed and also speechless ....... Hats off my friend

@SweetProjectCars 3 жыл бұрын

Our pleasure my friend! Thank you so much for watching, we appreciate it. Have a fantastic day. mad Mike the hammer SPC

@montyparks734 2 жыл бұрын

I notice you have mentioned a few different inverters and looks like you tried a few. My questioned is which one do you like best for deep cycle and standard 12 volt. This video was made awhile back so would like your latest thoughts. I'm ready to get on the Mike train---Thank you and have a good week---Happy Trails

@SweetProjectCars 2 жыл бұрын

Welder for Deep Cycle ONLY 6 Volt & 12V Batteries amzn.to/3yW4ihK and we use this for all Standard 12-volt Batteries amzn.to/2K1UsWQ Hope this helps Monty, thanks so much for watching we appreciate it. Have a great week as well my friend. mad Mike the hammer SPC

@montyparks734 2 жыл бұрын

@@SweetProjectCars Mad Mike--All I needed to know, Just sit back and watch the feathers fly, I'll pluck this chicken--Thanks again Boss and have a great week

@dawgduo Жыл бұрын

I did this with a deep cycle 12 V boat battery today using the recommended Deko welding machine and it restored it back to new condition. Hope it lasts awhile.

@SweetProjectCars Жыл бұрын

Glad to hear it dawgduo! Great work my friend! Thank you for watching and sharing your results, we really appreciate it, hope you have a fantastic week. mad Mike the hammer SPC