I had Error P03 which online Canon shows is error code 6000 which is paper jam? I couldn't see any paper. I kept trying and trying to follow instructions. Finally I decided I want to take this damn machine apart. And this video showed me exactly how to do it. And guess what? I found a small 2x 2 clear plastic stuck in the white rolling wheels. Where it came from I do not have any clue. It looked like part of the packaging. But it was stuck and I pulled it right out.

Viandant5: You sir, are a GENIUS. 😁 Thank you for posting this video. With concise and comprehensive instructions that even I ( a guy) can comprehend, and follow. 😁 My TS3100 was making so much internal rattling and noise; I was on the verge of pulling ALL my hair out, in frustration. You not only helped me fix/save my printer... you saved my SANITY! 🤣 Thank you. Thank you. And, THANK YOU! 😁👍👍👍

Many thinks!!! All best for you!

Gracias por tu video graciaaaaaaaaaas

لقد فكتت الطابعه لنهايه لم اترك اي مسمار او اي شريحه لقد انفعلت بسبب انحشار الورق ولم اجد اي شي ولاكن حصلت شريحه اخر الطابعه خضراء صغيره وفكيتها وحصلت تحتها قطعه صغيره من الفلين ولاكن كيف اتت الي هاذا المكان الي اخر الطابعه لم يكن موجود اي شي يدل ع الدخول للمكان والان انا لاستطيع ان ارجعها هل يوجد فديو لطريقه تركيب الطابعه نفس الطابعه والرقم

merci !

I found a spring I took out but cannot remember where it went

Is there a picture of the spring so I can finish putting it together

I unpacked the printer to the end, I didn't leave any nail or any slice. I got excited because of the paper jammming and I didn't find anything, but I got a slice. The last small green printer got it and got under it a small piece of cork, but how did it come to this place to the end of the printer. There was nothing indicates entering the place and now I can't return it. Is there a video of how to install the printer the same printer and the number

Around 6 minutes, what's the transparent plastic strip called / or for pls with L and R marked each side , and hooked, through the printer cartridges part?

There are two to flat strips under the control button panel. Minute 1:45 and 2:09. Do they plug into anything on the motherboard area? Minute 2:20. Trying to reassemble and want to do it correctly. Didn't take much apart since I found the issue of a paper feed. Please advise

Hi, thank you so much for your video!!! I found a brand new but abandoned Canon TS3150 next to the garbage containers and I'm willing to fix it! It makes rare noises when I turn it on and gives a blank paper. When trying to print, P08 error is displayed along with a 5200 code and the orange light is on. I disassembled the printer and everything seems to be ok inside. No ink, no paper jams.. I read this error is related to the ink pad, it may need to be changed or cleaned, but I also read it can be due to the cartridge not refreshing a resistance with too high temperature... I already cleaned the cartridges and they look ok and still contain ink but I don't know how old is the printer and how used it was before I got it... Do you think it can be solved simply by changing the cartridges or should I disassembly again and remove the waste ink pads? Lol I'm getting insane!! Should I just throw it away again? hahah If you read until here THANK YOU so much for your attention and help in advance! Greeting from Spain!! :))

hello, I took apart my ts printer apart because a plastic strummer was caught inside and now i can't really figure out how to reassemble it properly do you have away to show us how*? love it thanks

I have a question. If that wide wire thing, which is connected in the control buttons (upper), is damaged. What should I do? Can it be replaced?

Any ideas how to take the absorbers out of a TS5151? Thanks 👍

hi i have a problem, my bizhub 162 displays error code C0500 and when i check the fuser unit, it does not get hot at all, i tested the thermostat & the thermister and i found out they are ok, so i suspected the lamp but it seems fine by looking at it and i tested its continuity and it also seems fine, what can be the problem, plz i need help🙏

Hi, do you have an instruction for resetting Canon toner level after refilling the cartridge?

Nello smontare la mia TS3151 mi si sono scollegati i 2 connettori flat del tastierino dalla scheda madre. Uno piccolo (che va al tastierino) e uno grande (che va allo scanner) Hanno un lato "azzurro" e uno con la connessione "a vista" Qual'è il giusto orientamento dei cavi? Se nel caso inverto il senso succede qualcosa? grazie mille

Where to buy encoder strip and disk for my printer? Please help.

"Canon really made a mess with this cable" ... not only with this cable and not only Canon. Modern printers are a nightmare.

👍👍👍

what happened if the encoder strip is dirty, is there a way to clean it or any specific product to clean it or it has to be replaced?

La mia stampante Canon 3151 TS ha mangiato la carta, ma non si riesce a vedere.Sembra quasi sia andata sotto i rulli,cosa devo fare ? Grazie

I did all this because a pen got stuck inside my printer but now I am so confused because there is an extra connector in the cover of the printer (it looks kinda thicker than the other one shown in the video) and I tried putting it there where it is most logically should be, but the printer shows error :( It's kinda frustrating because I feel like I just made a small error and my printer is actually working. If anyone knows how to fix this I'd love to know. I only did all the steps until the cover got removed, that is all. Thank you so much for the video nevertheless, I would never have found the pen if I hadnt opened it!

How can I reset the error code p07 on TS3440??

Sir my TS3340 has an errorP02

Hi... wondering if you can help sir...i have pixma 3451 ...it fell down recently... fortunately nothing broke..printer works as well but two issues. 1. The plastic part has come out but i cant figure out where exactly it will fit 2. I think because of that part whats happening is page is not getting inside the printer via those two wheels .. basically that wheel assembly is not getting picked correctly..and i have to push page down a little If you can help please.. i can email you the picture of a part which fell down