Another great video. Love watching old RC gear getting used as it was meant to be. Would love to see a back to back motor test with a Tamiya Technigold and kyosho Spa 240ws. Back in the day they were both motors most of us dreamed of getting our hands on.
@TAMIYALegends5 жыл бұрын
David Chapman SPA240 😍👊🏻 I use to race my ThunderShot with that motor, good times. Thanks for watching
@NordicRC5 жыл бұрын
Great test. That 3S was Wild. Love that white DT and yeah, the Awanfi are great.
@TAMIYALegends5 жыл бұрын
Nordic RC Visions Thanks buddy 😊👊🏻
@mattmclafferty62655 жыл бұрын
Epic.Loved the 3s! Cheers Glenn
@TAMIYALegends5 жыл бұрын
Matt McLafferty Thanks Matt, yeah it ran really well in 3s, I have to be honest I thought it would be too much for it 😬
@hondofourfivetwo93475 жыл бұрын
That spot looks a lot smoother and just overall better than some of the other pavement places you’ve filmed. 🍺😎👍🏽
@TAMIYALegends5 жыл бұрын
Hondo fourfivetwo Yeah this is probably the best spot I’ve found so far 👊🏻
@matthpotte5 жыл бұрын
My first ‘proper’ motor, bought one new for my TT01 Merc CLK DTM back in 2004, still got it and have it in my Top Force Re Re at the moment.
@TAMIYALegends5 жыл бұрын
Matthew Potter That’s sweet buddy 👊🏻
@chrisstitt62345 жыл бұрын
I have the same motor in my hornet, only run nimh, it’s an absolute rocket, great vid
@TAMIYALegends5 жыл бұрын
Chris Stitt Thanks man 😊👊🏻
@bansheebandithot3505 жыл бұрын
Love that sound 😎👍🏻
@TAMIYALegends5 жыл бұрын
bansheebandithot350 Nothing like a Brushed Motor buddy 😊 Thanks for watching 👊🏻
@JimBoBJames-no5db11 ай бұрын
Great video Glenn. I've got 2 super Super stock RZ motors both in a Hot Shot and Super Hot Shot. On 2 S lipo envision battery with the full bearings in car I get consistent 44-45km/h or 26 nearly 27 mph. And this got me thinking you know who really needs brushless motors, because when brushes wear out you just replace them . And I don't really want to go with brushless in a Tamiya kit. I reckon also that 2 S lipo is just right for a Tamiya RC car and 3s is probably right on the limit or even too much. Puts the entire cars driveline under too much stress. 2s is the sweet spot. Brushed motors are still good enough for me and I will continue using them. On another note , I also have a Kyosho Fazer Chevy Camaro VE BRUSHLESS which I've got to the same speed well 59!km/h on a 2 S lipo and if I had enough space instead of driving out front of my house may have given a bit more. But too dangerous on public roads especially because of risking crashing into kerbs which can really destroy a car. Done it a few times and it's just horrible. Kyosho claim that brushless motor in the ve Camaro can get to 65 km/h. But that was scary enough for me , I don't need anything that fast. I'm more than happy with my brushed Tamiya buggies 👍👌 Love your channel Glenn, from Australia
@user-pj8hu4op6z10 ай бұрын
My TT02 is also a RZ powered. Reached 48km/h with 2S lipo.😊 I agree with you that brushless is too much unless you are on racing track. I usually play my tt02 on a deserted road with almost no traffic, but the road kerb always the enemy. If brushless on the road, probably my tt02 is a wreckage now
@sonicplayroompiano43027 ай бұрын
Nice man, can I ask what esc you use. I have a hotshot blockhead with sports tuned motor 7.2v nihm and wondering if I use a lipo battery whether or not the electronics would hold up? My esc is a hobbywing 1060. I'd be happy to buy this super stock motor
@markhollinshead57955 жыл бұрын
brilliant video as usual nice driving 6.03
@TAMIYALegends5 жыл бұрын
Mark Hollinshead Thanks buddy 😂👊🏻
@adamminchinton5 жыл бұрын
Great videos, been watching for a while, and this is my first comment. I've been playing with a few brushed motors for fun, and the Tamiya Super Stock TZ/BZ/RZ are all great. I stumbled onto a Kyosho Krypton Krystal 14T recently. I stuck it in my Egress and it can pull 55 km/h on just 2S, and I didn't even start playing with the timing yet. Love to see that motor in your cars.
@TAMIYALegends5 жыл бұрын
Adam Minchinton Oh that’s a new one, I’ll keep my eyes out for one 😊 Thanks for watching 👊🏻
@adamminchinton5 жыл бұрын
@@TAMIYALegends you can find it here: www.ebay.com/p/70564-Kyosho-E-motor-Krypton-Krystal-14/1004306811 It was part of a series of "mad science" motors, that went from 11T to 17T, but I've only seen the 14T motor.
@VoidXRC5 жыл бұрын
It's looking good out there in the sun. Nice runs with it
@TAMIYALegends5 жыл бұрын
Void X RC Thanks buddy, got to make the most of it now as winter is coming 🥶
@KyzerGB5 жыл бұрын
Great video again pal. Keep them coming . Just can't help sometimes I look away and it's like hearing Keith lemon talking about tamiya 😆😉
@TAMIYALegends5 жыл бұрын
KyzerGB Pmsl 😂👊🏻 Thanks for watching
@TheUsmc08025 жыл бұрын
It really is a great motor. I bought my son a KingCab to go with my Monster Racer that I've had since I was a kid. The Kingcab is rebuilt with the new Rere Super Astute TTC. The RZ matches up very well with the truck and transmission.
@TAMIYALegends5 жыл бұрын
TheUsmc1488 That’s cool 😎 I need to get a Kingcab on this channel 😊👊🏻
@withcookie55835 жыл бұрын
Motor looks like it does well, but well impressed with that dt02! Great vid, cheers Glen
@TAMIYALegends5 жыл бұрын
M Cook Thanks for watching 😊👊🏻
@mitymike5 жыл бұрын
I think I'm going to cram one of these in my lunchbox and run it on 2s also just picked up an adjustable motor mount. BIG PINION TIME!! 😁
@TAMIYALegends5 жыл бұрын
mitymike 1996 Excellent let me know how you get on buddy 🚗💨💨
@Leonsrchobbys5 жыл бұрын
Great video my friend smooth Run👍😊😎🇬🇧
@TAMIYALegends5 жыл бұрын
Leons rc hobbys Thanks buddy 😊👊🏻
@RCHobbyShed5 жыл бұрын
Good stuff. Goes great. Seems still very driveable on 3s. 👍
@TAMIYALegends5 жыл бұрын
RC Hobby Shed Yeah at the beginning of the video I say I’m only going to do a 3s flyby for the gps reading 😂 But in actual fact I ran the full battery through it 🚗💨💨
@ShenRC5 жыл бұрын
👍Nice! the DT02 chassis is great you can bash it it's pretty tough!
@TAMIYALegends5 жыл бұрын
Shen RC I know you’ve got a few of them buddy, this is the 1st one I’ve ran and I loved it, very cool 2wd Buggy 😊👊🏻
@TheOriginalS1_C5 жыл бұрын
Great video Glenn, I was thinking about getting an awanfi battery, might have to pull the trigger on one now
@TAMIYALegends5 жыл бұрын
S1_ C Yeah I’ve got a few now and there pretty awesome tbh, not had any issues with them 👊🏻
@rixsta9113 жыл бұрын
Your Tamiya plugs are limiting the power 👍
@danielkonrad14445 жыл бұрын
Im so jealous of your awesome collection. Gonna get a Dt02 myself i think.
@TAMIYALegends5 жыл бұрын
Daniel Konrad Thanks Daniel, The DT-02 is one of the best buggy’s I’ve ran on this channel so far, I absolutely loved it buddy 😊👊🏻
@bradkalman23535 жыл бұрын
Glad you asked that you have to get a DT 03 model now to if you don't also try all the black cat and motors and the TZ motor you need to try all the new brushed motors and you need to try all their brushless motor.
@TAMIYALegends5 жыл бұрын
Brad Kalman Sounds very expensive Brad 😂👊🏻
@bradkalman23535 жыл бұрын
Glenn you asked for suggestions you don't have to do them all at once is a. Of time you can do that.
@RCBirds3 жыл бұрын
Hehehe, tire torturing.... ;-) I have this motor in my Turbo Scorpion. It´s great. Couldn´t even test the car in our appartment. First I used the TBLE-02S in it. But this was a mistake. The ESC didn´t fit to the 23T. Now I got a Quicrun 1060 and man, this car is fun. Although I didn´t use LiPos.
@milosrcernycerny55375 жыл бұрын
Hi Glenn, I have this RZ (and BZ too) motor in my Neo Fighter and in NovaFox. Its good enough for these 2wd buggys. Fast enough, but not too fast and good controlable. I think, its an optimal motor for these. Enjoy it and have a fun.
@TAMIYALegends5 жыл бұрын
MilosRCerny Černý Thanks buddy 👊🏻 Do you notice any difference between the two motors you have?
@milosrcernycerny55375 жыл бұрын
There is another maximum revs (Its about 1000 revs) on the motor box. But when drive it, I didnt notice any difference. Only the color of the sticker is different.
@gaz19675 жыл бұрын
Great vid Glenn... Sun's out, guns out.
@TAMIYALegends5 жыл бұрын
Gary Rawlins Guns 😂👊🏻
@fabrizioviscardi405 жыл бұрын
Very impressive video!
@TAMIYALegends5 жыл бұрын
fabrizio viscardi Thanks my friend 👊🏻
@fabrizioviscardi405 жыл бұрын
@@TAMIYALegends Thanks to you for posting my buddy!
@darrengrimmer85415 жыл бұрын
Like that motor glen very good
@TAMIYALegends5 жыл бұрын
Darren Grimmer Cheers buddy 👊🏻
@originalrcfun73685 жыл бұрын
Super cool you compare nimh to lipo in your videos. I mostly use nimh, but hard to find good ones these days. I had most bad luck with chinese brands, but Orion packs works all the time👌Do not have Avanti batteries in Norway.
@originalrcfun73685 жыл бұрын
@Jinxx mk2 No. Just some small 1800 dynamite and bad Radient crap. Team Orion 3600 mah is very good, but will not fit all Tamiya models like TA03, TL01.
@jessemarkle5413 Жыл бұрын
Very nice
@rcalltypes82305 жыл бұрын
Nice video Glenn, the RZ motor is a well made motor. I had to fit ball bearings to my RZ motor, it’s even better with bearings 👍🏻 Just as I ball race all my RCs. I wasn’t sure if the motor would handle 11.1v lipo as it is rated at 8.4v. But it took it😂
@TAMIYALegends5 жыл бұрын
Rcalltypes Thanks buddy 👊🏻 Do the bearings make a noticeable difference?
@rcalltypes82305 жыл бұрын
Less resistance than the standard brass bushes. I have read it’s about 10% more RPM &Torque, but I haven’t tested it myself. The motor does run better with ball bearings IMO Also no need to worry about dry bushes👍🏻😎
@Bandit-Darville3 жыл бұрын
Hey @Rcalltypes, can you point me in a direction on how to replace the bushes with ball bearings in this motor?
@rcalltypes82303 жыл бұрын
@@Bandit-Darville Tamiya Legends, has a video on it now. So does RC Action Australia. Watch both videos, well worth it. I’ve been fitting bearings to super stock motors for years. Any way I could reduce friction, I would do it.
@Bandit-Darville3 жыл бұрын
@@rcalltypes8230 I found the RC Action Australia video after i asked the question, thanks for the pointer!
@stumpycatvm71153 жыл бұрын
my RZ installed in my Re Re Terra Scorcher is overheating and shutting down running the ESC TBLE-02S, don't know if its the ESC shutting down but the motor is real hot- a lot of compression with this motor, I could check gearbox movement with a standard motor by moving the front two wheel and see them drive the rears, but only with the standard 540 motor, interesting side note I'm sure your aware of.
@rcl3000183 жыл бұрын
Maybe go down in pinion size? I read somewhere as you go higher in power (lower turn motors) pinion size should be reduced.
@stephenmanley40975 жыл бұрын
Good to know that motor runs on 3s 👍
@lualrosaal3 жыл бұрын
The only bad thing I have to say about the RZ motor is.... It's too fast for me. Even on 7.2 Nimh. I put it on a TT-02R chassis and with the stock (very hard) springs it was too much to handle. Have to try softer spring on the rear suspension to see if it's more manageable. Great video!! Thanks
@MavAuto-Pete3 жыл бұрын
Looks really fun though on the 3S
@davidturner23655 жыл бұрын
That thing is gunna eat motor brushes lol great vid
@TAMIYALegends5 жыл бұрын
David Turner You’re not wrong David 😂👊🏻
@dave6919745 жыл бұрын
Need to get one for my lunchbox.
@TAMIYALegends5 жыл бұрын
David Cotter Yeah definitely David, I would imagine it’s the perfect motor for the Lunchy 🚗💨💨
@sonicplayroompiano43027 ай бұрын
Nice one mate. What esc are you using?
@aviano725 жыл бұрын
Awesome video ! That is a great brushed motor. I'm wondering how it is compared to the Super Stock BZ. Also that DT-02 is such a great car to build and run. I say it like Alex Albon's race engineer at Spa: Excellent !
@TAMIYALegends5 жыл бұрын
aviano72 Love it 😊 Thanks for watching buddy 👊🏻
@mistervaso9 күн бұрын
I am getting to electric RC , i just bought this motor, and when I spin the spur gear the motor doesn’t spin freely? It spins with a clock feeling 6 rotations. Is it supposed to do that or did I get a bad motor?
@bradkalman23535 жыл бұрын
Glenn I need them quicker than that brushless for me on model.
@Triggered-RC4 жыл бұрын
I have 4 cars running BZ superstock motors. Have never tried on 3s though... Wondering what 3s would do for my Lunch Box running the BZ ;)
@TAMIYALegends4 жыл бұрын
Kalan Star Excellent well I have to say the brushed motors aren’t made to handle 3s power, so the life of the motor will decrease! But if like me your cool with that, have fun my friend 😎🚗💨💨💨
@johnnyutah60565 жыл бұрын
Loved the 3s!
@TAMIYALegends5 жыл бұрын
Johnny Utah Yeah it ran pretty good on 3s buddy 🚗💨💨
@leehurst69225 жыл бұрын
Where is the dark impact video you mention Glenn?
@TAMIYALegends5 жыл бұрын
Lee Hurst Sorry Lee I’ve released this video early 😬. The DF-03 will follow this month 👊🏻
@rcaddictgarage5 жыл бұрын
👍
@KamalNsouli2 жыл бұрын
I know this is an old vid, but do you by any chance recall what size pinion you were using on this motor? It looks about right with torque and speed.
@TAMIYALegends2 жыл бұрын
I’m pretty sure it was a 17t my friend 👊🏻
@rcl3000182 жыл бұрын
If you get the 19t pinion on the standard torque tune motor you will get around 36kmh on nimh as well. Going to have to try my RZ on the 19t pinion.
@MavAuto-Pete3 жыл бұрын
I've got my buy Lancia Delta running on on upgraded high-speed spur gear and a 19 tooth pinion Gear ear with this motor on the hazard I can get nearly 42 kmh and that's running on 2s
@robskot13 жыл бұрын
Hi...just getting back into the hobby after 20 yrs...I am about to build a Terra Scorcher Re issue...I am thinking about getting this motor for it. Is this a good idea? I was planning on using a HobbyWing 1060. Do I have to use a different pinion gear than what's included in the kit? Thanks for your help!
@alanmorris87835 жыл бұрын
Can the Tamiya ESC use 3s without blowing up? I’ve heard both views. I’ve got the Tamiya fan on top. Cheers
@TAMIYALegends5 жыл бұрын
Alan Morris Hey Alan, I’ve never tried one on 3s tbh, I know Tamiya don’t do Lipo, there battery is the Life 😬 I’m out with the TB-01 Rally Car soon which is fitted with the TBLE02s ESC. I run that on 2s, but I’ll take a 3s with me to see what happens 😬🚗💨💨
@cytwlm5 жыл бұрын
@@TAMIYALegends Yes, I also want to know TBLE02s ESC to run on 3s battery, with this Super Stock RZ 23t
@willreardon51163 жыл бұрын
Hey Glenn. Have you ever used the Tamiya Commutator cleaning brushes? Part 53486 is suitable for the Super Stock BZ and 53487 for the RZ. You are supposed to remove the motor from the car chassis, take off the spur and replace one of the brushes with a cleaning brush and run for 2 or 3 mins. Cannot for the life of me get them to work. Any tips greatly received!
@TAMIYALegends3 жыл бұрын
Oh wow no I didn’t even know that existed 🤔🤷🏼♂️
@willreardon51163 жыл бұрын
@@TAMIYALegends Thanks for getting back to me Glenn. It’s really weird - the cleaning brushes are mentioned by name, on the bottom of the instructions you get with the motors, as the recommended way to clean the commutator but no-one has ever heard of them - let alone used them. I certainly can’t find anything on KZfaq of anyone using them. A possible inclusion in your next motor vid? 😉
@alerossi85645 жыл бұрын
I need a bz motor for my Wild one
@TAMIYALegends5 жыл бұрын
ale rossi Thanks for watching 👊🏻
@thomathomakos69463 жыл бұрын
Hello! ! And. Good Year!!! The stock mabuchi motor can l play with 3s? ?? With Hobbywing 1060 ???
@Bandit-Darville3 жыл бұрын
You can play with it but the motor won't thank you for it i'd imagine.
@andrewmatthews72742 жыл бұрын
Can you tell us what esc you're using in this video
@Mini-z19945 жыл бұрын
Oh that's a 23t ? flies pretty nicely down the road on 3s, thought it was more like a 17t motor or similar but i guess they are even faster if the esc handles that on 3s. Maybe you can try the reedy radon 2 crawler 16t motor ? Feel free too try these motors out as well, possible the reedy motors are these but rebranded too their own brand with how cheap they are at around 25 usd. www.banggood.com/SURPASS-Hobby-Brush-540-11131620T-RC-Car-Motor-For-110-Crawler-p-1524962.html?rmmds=buy&ID=47249&cur_warehouse=CN Maybe you can look for a double 15t as well.
@Mini-z19945 жыл бұрын
Seem to have found a few of them on amazon uk as well. www.amazon.co.uk/WEIHAN-SURPASSHOBBY-Brushed-Waterproof-Crawler/dp/B07WP42MNY/ref=sr_1_59?keywords=motor%2B540%2Bx2&qid=1567498742&s=kids&sr=1-59&th=1 Maybe the Abisma thrust 540 brushed motors could be worth a try as well, think they go down too 8t x2 which is quite fast.
@TAMIYALegends5 жыл бұрын
Marcus60661 Excellent buddy I’ll have a look at these motors 😊👊🏻
@n0578287 ай бұрын
I’ve just ordered a scorpion will get this motor on Amazon Aus under $70 bucks delivered. ESC and 2s battery guys please help ?????❤
@martinneps93873 жыл бұрын
How much are these motors and where can I purchase Them please comment back in let me know thank you very much
@lunar14784 жыл бұрын
Can you use this motor with a Traxxas rustler brushed esc?
@TAMIYALegends4 жыл бұрын
LUNARSHOTZ Yes you can I just google it and it has a 15t motor limit 🤩👊🏻
@camrowdrone64975 жыл бұрын
It looks impossible too roll or was that your driving 👍🏻
@TAMIYALegends5 жыл бұрын
Cam row drone Definitely not my driving 😂👊🏻 I have to say I really like the DT-02, this is the first one I’ve had on the channel. It’s a great handling Buggy and when you see it on the gravel it’s even better 🚗💨💨
@thegreattreon01775 жыл бұрын
I'm shocked a 23t motor could handle a 3s battery, this gives me hope!
@TAMIYALegends5 жыл бұрын
David Jenkins Yeah I’m not sure how long it will last though 😂👊🏻
@BigRed4075 жыл бұрын
What ESC are you running?
@TAMIYALegends5 жыл бұрын
Big Red That was the Hobbywing 1060 buddy 👊🏻
@RobPollen3 жыл бұрын
What ESC are you using ????
@TAMIYALegends3 жыл бұрын
That was the Hobbywing 1060 😊👊🏻
@RobPollen3 жыл бұрын
@@TAMIYALegends just built avante 2011 I put in a super stock bz with 23t pinon and it killed the tble-02s .. I'm looking for replacement that can the extra power load
@TAMIYALegends3 жыл бұрын
@@RobPollen Yeah the 1060 is the one you want my friend. The TBLE02s will run the super stock but it need the ESC fan fitting to it 😤
@Bandit-Darville3 жыл бұрын
@@RobPollen The tble-02s should be able to handle this motor no problem. Did you fry it on 3s perhaps? That esc is not designed for 3s power..
@kevinrachmanherdyanto4 жыл бұрын
can i use tamiya esc tble-02s for this motor ?
@Bandit-Darville3 жыл бұрын
No problem!
@alexanderirwin72714 жыл бұрын
Any reviews where the cars are driven on a course instead of an empty car park
@TAMIYALegends4 жыл бұрын
alexander Irwin Unfortunately not, I don’t have anything remotely close to me over here, so I’ve gotta make the best of what I’ve got 😬 + this was just to test the new motor out. Not sure if you’ve seen my normal running videos but I try to get they on the gravel as well 🚗💨💨 Thanks for watching buddy 👊🏻
@hellion17703 жыл бұрын
Please let go of the tamiya plug and the cheap bullet plugs on the motor, even if conveniant.
@rcl3000183 жыл бұрын
What would you suggest replacing them with? I know some people replace the Tamiya plugs with the T Deans. But what about the bullet plugs?
@_blood_moon_proto_1500 Жыл бұрын
i love tamiya, but they're electrics scare me, they even have brushless motors (i have 1 brushless rc and it scares me, no really, its a huge "1/10" rc car, do note the quotes, called the ftx rockatan, its 3s and i swear it wants me dead)
@jessemarkle5413 Жыл бұрын
Stop turning so much an let r rip
@bradkalman23535 жыл бұрын
Glenn I need them quicker than that brushless for me on model.