He does make a lot of his lessons funny

True !!!

Taryl is like twenty some steps ahead of any high school shop teachers I've ever met. I work off and on as substitute teacher here and not even in my area where I live. I at an inner city school near Reading Pa... I want to tell ya the school board is probably only capable of running a liquor store and that's about the extent of their knowledge. When I said that at meeting about 2-3 years ago it was one of more infamous smart ass comments people still remember me by that zinger because people and parents were spitting coffee all over each other laughing their asses off. People wanted me to run for an open position on their school board. I said within a week I would end up earning a lifes sentence at the state pen....

I've ran crews and trained guys in electrical, welding and ironworking and mainly air conditioning, now retired. I was always calm and cool and I had really great results in training but, I never thought about adding humor. It immediately makes sense. You sir are a genius.

Lol... mine said samething

Just get out the duct tape and tape it back together...

Nope just wait till you try to take the blade off an old brush hog. Agony and you’ll immediately wish you were messing with a lawnmower

When we get older and fatter our belts break lol.

And don't just slam it into operation. Ease into the engagement so you don't shock the belt having it go from 0 to full speed suddenly.

Wrong the pto is designed to start at full throttle! If you start at low throttle it can damage pto

Says so in the owner's manual as well

Good luck what kinda mower do you have

@@hunter7476 TORO TITAN Z 5200. Earlier this spring, I took care of a Fluffy problem.Taryl truely fixes all!

Tayly i got a cub cadet 1040 cant get belt right .seems it slips no speed or drive problem.anyy suggestions.

@@harryboeckler7198 Examine the deck pulleys. My nephew has a CC and it was throwing the deck belt constantly. He couldn't figure it out. I looked it over and on close inspection, you could see the tension pulleys mount, which should have been designed to have either a thicker threaded mount, or enough room for a nut under it IMO, had worn from the belt tension pulling on it. We had to replace the whole arm and that solved the problem. Part was a 'Idler Arm Bracket'. We also replaced the 'Idler pulley' because the bearing was shot, the Extension spring, belt and belt keeper rod. All those parts including shipping came to $173. It now works like new.

Thank you.

Send that man a case !

Amine are old mechanical ones with the shaft on it good point

Now for what makes the squeaky belts maybe?

That’s why you should cut your grass weekly I mean that’s how I do it and it looks nicer when your done if you cut 16 inches of grass it’s all dead because it didn’t get any grass plus it bogs down there mower if I want to cut that I use an old self propelled garden way sickle mower works great

Well, if you go real slow, and have the deck set high, they'll bush hog pretty well. Depends on the HP too. I end up bush hogging sometimes when my horse pasture gets out of hand, when I've been busy on other projects and neglected mowing. I've cut waist and even shoulder high weeds and grass with a LT1000 with a 17 hp Intec, and it never bogged down, I just had to go real slow. Main problem bush hogging with a grass mower is the deck. It's too enclosed. Bush hog and brush cutters have the front of the deck open, so the blades can hit the weeds without being bent over by the front edge of the deck. I recently purchased a junk LT1000 with a deck for $50, and am planning on cutting the front and sides of the deck away, and installing it on my good LT1000 and see how that works cutting weeds and brush. The worst problem really with all of these riding mowers is you can't raise the deck high enough for the best brush hogging. I'd really like to be able to have the deck at least 6 inches off the ground. But all these mowers are designed for mowing golf courses it seems.

@@hunter7476 I have one of those Garden Way sickle mowers. It's sitting in my barn unused for many years now. I got it used, in good working order, with two blade heads. The thing breaks teeth way too often, and they're a pain to replace. Plus, you can't use the cheap normal teeth for farm sickle bar mowers that you can get at TS. You have to use TB's special teeth that cost ten times as much. Eventually both cutter bars, the steel strip that the cutter teeth are riveted to, snapped in the middle. That little piece of steel costs $150 to replace. They get you coming and going. Someone needs to devise a way to make a better cutter bar for this little mower that can use regular farm teeth IMO. Till then, brush mowers that simply use a normal lawn mower blade are far superior because they are cheap, way more durable, and easy to sharpen or replace if needed.

Or the shuttle

I was able to mow 2 foot tall grass with a 1987 Craftsman lawnrider with a 12hp OHV engine in it. 36" deck on it. what I did to do that is had the deck set to the highest setting and went in first gear, full throttle. it cut that grass like BUTTER when I did that! never bogged down once. (the highest deck setting is I think 6.5 inches off the ground if I'm not mistaken) full-on BEAST of a mower just a little tip for y'all: if you encounter tall grass while on just a basic riding lawnmower, mow it in first gear with the deck at max height *THERE'S YOUR DINNER!*

angry belt dance, yes, I've taught that one at my shop.

Must own some of Hamms stock.

Get you a belt measuring tool from McMaster Carr 😉

Don't think i would agree with that description. Worn pulleys would lead to the exact opposite of biting. Slippage, therefore heat, and glazing of the belt would be the result. Worn bad enough, the side of the belt isn't gripping the pulley at all, and could or more likely be riding on the inner circumference of the pulley.