Mad respect man knows his stuff

Homie straight glitched out in the beginning

Very well explained as always. I didnt think I needed to balance shaft delete, until my engine started stalling at stop lights after a rebuild. The belt was all stripped, and the bearing burned out. Maybe some contaminants were left in the block and eventually collected in the inner bearing. There is a nice balance shaft kit which uses an aluminium plug instead of just the bearing rotated which I would get next time. Edit: you should catch up with Legion Elite motorsports hes into starions and 4gs

Man u so far ahead of me lol Keep going man I got a oil pressure problem ether clogged or bad pump

Where can I buy the oil pump delete kit for a 6bolt 1g 4g63t. I spun the bearing that goes further back on the counter weight shaft on the oil pump assembly side. I saw 👀 you can just throw them away lol delete them 🔥. Where can I buy these delete kit to delete both sides counter weight shafts.

Very nice. Thank you! I wanna install a actual oil pressure gauge instead of the factory light. What plug do I use to hook it up on block. Thanks friend

Good explanation of this mod 👏 I have a question , can I cut off the end of the front balance shaft instead of buying the NA 63 delete ?

Hello bro o have 1 question? Does the right side balancer also have lubrication through the block under the bearing? So if I remove that bearing, will there be a hole that is normally covered by the bearing or will there not be a hole? I hope you can help me to know

Man, couple months ago my balance shaft belt flew out the right tire, had to stop right quick and see wth just happened😭

Good teaching , what is the reason of blocking those oil holes?

فاتح محرك مسيوبوشي بستم اصعده ماصاعد بل كامل باقي خمس مليمات هاي عادي

How did you counter the vibration from deleting them ?

ATTENTION TOYOTA 2.7 LITER 3RZ-FE ENGINE OWNERS: I don't know about other engines, but if the balance shaft bearings in the 3RZ engine are allowed to wear too much, this causes the balance shafts themselves to begin spinning right against the engine block where the bearing has worn out. When this happens, the balance shaft badly scores the block, rendering the block totally useless. Once this happens, the engine block is nothing but scrap metal. Deleting the balance shafts in the Toyota 3RZ engine is HIGHLY recommended. Deleting the balance shafts and all related components ( gears, chain, brackets, etc ) results in less parasitic power loss, giving you a noticeable improvement in throttle response as well. I bought my 2000 Tacoma 4x4 with 3RZ-FE engine brand new & deleted my balance shafts recently. I can really notice the difference in throttle response especially from a standing start, even during normal acceleration. ( This slight power gain will not show up on a dyno, but your seat meter will feel the difference. ) Although it's not necessary for deleting the balance shafts in the 3RZ, LC Engineering ( "LCE" for short ) sells a nice balance shaft delete kit for the 3RZ engine that costs only $99.00. This kit comes with literally everything you need for deleting the balance shafts, including a drill bit, tap ( for threading an oil galley that will no longer be needed ) a small plumbing plug to plug the oil galley after drilling & tapping, 2 "dummy" bearings ( that replace the real balance shaft bearings ), a nice specialized tool for knocking out the original bearings and is also used to install the new dummy bearings, plus LCE's trick custom oil jet with 2 new mounting studs. This trick new oil jet squirts oil only on the timing chain whereas the original oil jet sprayed oil on the balance shafts chain as well. This kit saves your engine from wasting oil pressure on parts that will no longer be in the engine when the balance shafts & related components are removed. Oil will now only be sprayed where it is needed. The only thing you'll need to use with this kit is a common drill, a T-handle tapping wrench, a tube of sealant, and a common tool/wrench set. The kit comes with complete instructions and LCE even has a how-to video on their youtube channel. Personally, I can't detect any added vibration with my balance shafts gone.

أريد ارتفاع بستم