Уважаю! Золотые руки! Главное, не останавливайся. С наступающим всех!

Since youtube is removing shortly annotations I’d thought I’d back them up so to speak since I think they’re important here. 0:08 Rolling paper until there are no gaps 0:23 untwist it, cut smaller part (7.1) and roll it again using two planar surfaces (for example using ruler) 1:18 Cover with super glue to make it stronger 1:34 cut part 7.2 and roll it into a tube 2:00 cover 7.2 inner surface with PVA glue 2:10 cover part 7.1 with part 7.2

Fantastic!!!! Thank you for the templates!

This is inspiring!

Отличный канал, отличные видео, есть небольшое пожелание, рассказывай, про модельки ну и русского языка побольше, а так все отлично, удачи земляк)

Hi, thank you very much for the templates. I'm trying to make it in scale 2:1 from yours (larger) so I use 0.3mm thick paper. I have the entire lower part with cylinders working fine and without much friction, but I am stuck at the top part, valves specificaly. When I glue the valves (11.1 and 11.2) into the top part 10.1, they seem ok, but when I put the axis 7.1 and 7.2 in it and spin it, the valves open one at a time, but after a few spins they stay open permanently. If I would continue with it, the air would go to all cylinders at once, and the engine wouldn't work. I even tried making a paper spring, similar to the one you made in the throttle for this engine, but even then the valves didnt close, and it was much harder to spin the top axis, so I had to take them out. One thing I didnt figure out from the instructions is whether the full-line rectangle in the parts 11.1 is supposed to be cut out and then glue the complete part 11 to part 10.1 using only the far side of the rectangle and let the side parts of the rectangle free to be flexible. I didnt consider it at the start, so I didnt remove it, maybe this was the mistake? May I ask then, how did you make them close? Do you have any suggestions please? :)

Круто.

very tanks

Sickkk!

Hey, been watching almost all of ur videos, and I was wondering if u ever thought of building a model vehicle powered by ur paper engine and fuel on mini CO2 cylinders? that will be epic!! imagine a paper RC model vehicle with realistic sound effects anyway keep up the great work, looking forward for ur next video

Could you make a bigger version of the template? In my opinion it's wayyyyy too small for the average person to do even though I do have lots of experience with papercraft it's still near impossible to me.

I've often struggled with this bit. Didn't know the epoxy and ruler trick =D

Очень понравились Ваши работы. Скажите, пожалуйста, а чем Вы обрабатываете бумагу? Это эпоксидная смола (Epoxy)?

how long do you work on a new design?

Bro we need full vdio of v8 engine pls make it 👍👍👍👍😄😄

Is there any ways to scale up the template...? i have fat fingers.

What software do you use to model the engines?

Will you release templates and instructions for the rotary as well?

I dont have headphones, what was that glue

please give the link of rotery engine

can we use 0.05 thickness sheet

To make the entire engine, did you use glue the entire time or did u ever use tape?

how did you make the cylinder head or valves to make the air pass into the whole cylinder

I have a question how do the air work in V2 paper engine if I know i can make my own paper one

Sir,We have to apply each part with super glue

can i make this engine for my youtube video.

Could you just use a toothpick

Нет просмотров:/

"not very experienced" right and I'm the president of the usa