How to Blink a LED | #5 STM32 GPIO output

Рет қаралды 51,917

3 жыл бұрын

This video explains the following:
1. Project creation (quickly)
2. GPIO configuration
3. LED blinking code
4. Creating a debug configuration
5. Line-wise debugging
Kshitij Dadhekar

Пікірлер: 30

@kulaniscap 2 ай бұрын

After struggling to Blink my LED for hours, this video gave me a lot of background info that helped me Blink the LEDs on the STM32F429I-DISC1

@biglebowskee 3 ай бұрын

Thanks so much for this amazing tutorial. You are very good at this type of teaching. I hope you continue to produce these videos.

@maxpowa7430 2 жыл бұрын

Thx Buddy! This video made me understand much more about the structure of an microcontroller program! In University we lear to program and what are datatypes or Objects and so on. But only because u know whats an uint16_t datatype is u dont understand the much bigger programmingtext just only in the main.c file! With ur explanations where to find things like the defines or the functions them self i can now use my learned basics to write my own program. even if its just a blinking LED. Great work and keep up doin videos like this for DAU's like me! All the best for u!

@Mr0neShotAway 3 жыл бұрын

These videos age great! please continue!

@user-oc9fc1sm4p 3 ай бұрын

😃

@shivamchoudhary6280 3 жыл бұрын

learning a lot from these videos.

@abelashenafi6291 4 ай бұрын

Thanks bro, you're video series are just amazing. Thanks for sharing. Kudos

@Egon3k Жыл бұрын

technically speaking, 1s on/1s off is half a hertz, but good and detailed explanation :) I would really like to know, why it is required to enable the RCC_AHB1ENR for GPIOA

@rosymelody4125 2 жыл бұрын

i tried to do all the settings accordingly, but when we configure the led i/p low these are the settings are not shown in my software

@user-qz1xb3co9d Жыл бұрын

Where you did your mtech in embedded system?

@user-xd3fh6nm7x 9 ай бұрын

great job! Thanks

@bangingshock 2 жыл бұрын

Nice videos! Can I set the output logic high to 1.8v instead of 3.3v?

@TerminalTwo 2 жыл бұрын

Nope, not unless the GPIO level specified in the datasheet is 1.8V. In this case you will have to use a level shifter IC.

@megumin20 Жыл бұрын

Honestly this helps a lot. A little suggestion. You may need a better microphone. Hope all goes well.

@sudheerkumar5966 2 жыл бұрын

Very good sir

@bedirhankahvecioglu8462 5 ай бұрын

i love you so much youre thinkig like me and i love your videos. When i improve myself at this coding stuff. i will remake your videos in my language if you accept it.😊😊

@tanoojkumarpc459 4 ай бұрын

Thank you for the video, ####working

@mehmetylmaz8359 2 жыл бұрын

The codes Download Verified Successfully but Led of STM32 dont blink, why?

@stm32user 3 жыл бұрын

Hi. Post more videos

@claudiaurena6813 6 ай бұрын

gracias

@Makarand_Ronghe 3 жыл бұрын

It was a very long break!

@ezhilv4358 5 ай бұрын

Iam getting error in initializing st link device

@joost_schiphorst 3 жыл бұрын

f3 isn't working, is says it couldn't find this symbol in the index

@TerminalTwo 3 жыл бұрын

May be the function/macro is not defined?

@veeranjibandaru2550 Жыл бұрын

3 LEDs also process

@GorkemEfeDemirbas 5 ай бұрын

in Debug Config section when i try to scan the program cannot find any st link but i am using nucleo card and its connected and leds on the card is blinking what can be the problem?

@yeungster1013 5 ай бұрын

I also have the same problem. Have you found a solution?

@GorkemEfeDemirbas 5 ай бұрын

@@yeungster1013 yes i found the cable i used was the problem i changed the cable and it is fixed

@ryangosling7954 Жыл бұрын

It's blinking, but i have a question. I tried to write a function before the "while", that blink exactly 10 times. It blinked 10 times, but after that led didn't turn off, so it was still bright. Any advice how to force it off after the cycle?