Best Electronic technician I have ever seen..how I wish your to be my master❤

I have watched mostly all your videos. For the first when I see this problems. I myself I couldn't figure out that the Nan processors was the fault. Thanks for this video ❤️🙏

I always watch and like your videos to help support your channel. And it seems like I always come back and say "USE MORE FLUX"! Regardless of the fact that they were un-used, you would not have ripped those traces off that board if you had used more flux! Apply flux first. Apply low melt solder. Apply flux again and use wick to remove most of the low melt solder. Apply flux again and reflow remaining low melt solder to lift pins slightly and hold till solder freezes. Repeat on other side. After chip is removed, Apply flux again and use wick to remove ALL low melt solder mixtures from traces. Apply flux again and tin all traces with leaded solder. Position chip, apply flux again, and solder pins in place. Flux is used to help the smooth uniform application of solder. Flux reduces the soldering time and heat applied to components and board itself. Flux greatly enhances solder joints by reducing dry brittle joints. Flux males you look more professional by reducing the number of savagely ripped off traces on customers boards, and broken components. 🤣🤣 Flux in the end saves you money because you use less of the expensive low melt solder. I could have removed at least three of those chips with the amount of low melt you used in this video. NEVER leave any trace of low melt mixtures on boards and components as it is not suitable to use for application of components. Dry brittle joints, low melt temp, corrosion, etc, etc, etc Use more flux. Great videos! I have not seen the candle trick! As an old repair person, that is a new one to me. I have always used a cotton swab with isopropyl alcohol to check for heat till thermal cameras got cheap enough to afford. Good luck, keep making videos, They are great! USE MORE FLUX!!!!! 🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣

Nice work. Respect how you work. You are the expert in soldering.

Nice Work Tevz.

You give a very helpful idea for us good luck Brother. I m from Pakistan Karachi

You removed the chip nicely, with out more heating sir, that is good,and life long for the chip, thanks god there were no connection under the big chip😊 and best flux used . Use more flux to connection and remove sir, take it easy 😊 good and calm job done 👍

Nice repair tutorial watching here sending full support thank you for sharing

All your video explain very crystal clear knowledge easly understand

Nice work... Well done. ❤

You are a great inspiration to me, thanks sir

Hello. That TV model is ISDB-Tph ready and can now be used without any ISDB-Tph set-top box. All you need is to connect your UHF Outdoor Antenna directly to the TV using RG6 coaxial cable and scan for channels that are now testing Digital Terrestrial Television Broadcast.

You made my day 💕

Great work, i like all your videos thanks for share 👍

very informative video...thank you sir tevs

Good knowledgeble video sir thank u good job

Thank you for sharing knowledge and posting through this video

galing talaga sir you are the great technician😊

Excelentes videos, gracias por su aporte

great job master ❤❤

Very nice quality repairs 🤙

ang galing galing talaga. pano nya nalalaman na yun ang papalitan sa napakadaming components na andun...

Muy buena clase amigo tevz estoy con tu membresía y e aprendido mucho de tu canal gracias

Good work sir

Lupit mo tlga sir

Good job bro

Well Done teacher and good work it's nice 👍👍👍 good luck

Nice job great job and good job

Very very good sir.🙏

Very nice Sir ,India

Thank you. God bless you.

Full watching master 👍

متشکرم ازت دارم از دانش شما بهره می برم

Its Great Nice work

Great work it’s not easy

Picture quality also superb

Thanks for sharing idol

Turkish language subtitle bro,wonderfull work

Nice work

Very nice information sir

Thanks for sharing knowledge..Great channel

Yes great work

Great job lakay Change board and swapping nan ic.nice idea Thanks for sharing with us Ay apo noise bleed lakay😅

Good job like always👌 If you inject voltage and use thermocamira will show you the component short

nice ,, idea gain

Thanks sir ..

Salam kenal kawan dari indonesia.. Salam satu hobi

Mahusay tlga sir..

galing

Thanks alot

Greate

👌👌👌

👍 from italy

👍👍👍

Nice job. You don't have the tools to read the good nand chip and flash it to bad or other/new nand chip?

👍👍👍👍

🙏❤️👍🏼👍🏼👍🏼👍🏼👍🏼

Hi sir I have a 43"tcl tv no images on screen but sound on and backlight on I think the panel bad but is there anyway I can bypass some track goin to the screen

Love the video 🎉. But why do people say if a CPU is soldered in. Then a laptop is trash. If you can replace chips like that then why not CPU ?????

Friend I have a problem with my Sharp Aquos smart tv LC-60C6600U. Boothing stuck at the SHARP LOGO. I tried using the downloaded firmware to do new installation but it didn't work. Can you help me with that. (When I in-set the flash drive and plug in the power cord, it does not booth itself.)

Nice work, but the swapped board can not be repaired?

newbie is watching

My question master, there is a polarity d smd capacitors.

New subs here Tnx

sana magawan po ng video yung s creen ng flat t.v my nag bblink n box at my red n sulat n V8- MSV59PA- 144V002

BRUHM BTF-39SN back light is on but the VGH and VGL is not coming how can I fix this problem

Napanood ko sa video ung ginawa mong sharp na blinking red light ang tanong ko pwde bang palitan ng ibang backlight ang sharp.

Pak tolong tambahkan subtitle bahasa Indonesia 🙏

any video sharp led TV lc-40Let185m by to android full detail's

Knowlege is huge, but use flux! This soldering is sucks😉

I'm wandering what is wrong on the other board now :). Most of the people won't have some spare board ;) to fix it.

why didn't you repair the original card?

Nice work, Can we change with a new NAND memory? Then will it work?

Paano ayosin stock logo din restart back to logo

hello my friend i am a tv repairman i have some doubts about panel and LVDS signal with samsung screen repair

file bin nand memory

Paano ayosing stock logo same model Lc40le360d3

siguro itype nyo na lang e "led" instead of "lead" kasi "leed" yung basa ng text to speech

you just replace the board, not totally repair the main board which is faulty why?

How do you know the issue on the memory chip ?

Which contre

why now use update software

Neden Türkçe dil alt yazı seçeneği yok, onuda ekleyiniz,

This is not the right way to solder at all

you need to work on your soldering skills

false

Nice , but think u could use more flux and desolderig wick...it would be much better ....best regards!

Why don't you use short killer.method

You are a great inspiration to me, thanks sir

sir exelint work great information

👍👍👍