With your videos and the book. I finally built my own TH400. Thank you so much for all your knowledge. I couldn’t be happier it works like a champ and has been holding all the power I can throw at it!!

Again another awesome video on the subject. I am looking forward to the next one. Thanks for taking your time to get these videos.

Just picked a th400 4x4 up last night , plan on using it in my chreokee with a small block 350 until I build a big block, these videos are full of great info

Hi Sean this is Chris from Wisconsin looking forward to doing the do it yourself to my chevelle 1970 454 th400 an old friend of mine helped me do one years ago but I forgot how to do it thank you so much for posting this now I don't have to call him it used to chirp second gear and third gear would hit very hard at 90 mph can't wait to do it to my Chevelle

Great idea on the dip stick mounting trick and not going all the way through. And repurposing the LS motor mount bolt. I'm stealing this! I use a 1/16" npt to plug the hole behind the pump, the tapered sealing makes me feel warm and fuzzy relative to a straight thread although it's probably just as safe.

Excellent video again. Going to dive into my th400 at some point, has started to slip 3rd gear, not all the time but every now and then.

I have watched all your videos enough now I feel comfortable about building a th400

Thank you Shawn for sharing your knowledge..

This info is gold mate, thanks for sharing👍

Works like a dream and super easy modification

I just got off the phone with my buddy who is 2 states away I'm going to bring him my 2 speed turbo 400 and have him put a manual valve body in it. And I talked to him about the 3 speed turbo 400 I blew I told him I was going to have him set it up with a trans brake he said he would have to see if he would be able to do it with that case because of some of the modifications he did the first time and what transbrake valve body I bought. If that won't work I'll have to find another case or buy a aftermarket case

Thanks for the video. 👍

Thanks for very good videos. How about removing the second ring on center support for dual feed, somebody says that it should go?

Thanks for your awesome videos. What are some suggestions for a THM400 with a harsh reverse. Looks like the Transgo reverse kit just tightens up the reverse band and restricts the feed down to .090. Direct drum has the waved cushion with clearance set at about .050. Direct drum is not dual fed. Thanks for your time. Steve

Good video man thanks for all the info 🍺🍺

Always great information

Hey shawn, i did the first part of the video, on my sons s10 Transmission, it worked good, except i have to stay on the throttle a little to keep 3rd in, i bought a new modulator, adjusted it, same thing, decided to go full manual, pulled it back out, removed the tubes, blocked them, drilled the hole for the governor flow, did not mess with the boost valve but my issue now is it takes off in second, has a nice third but no first, what am I missing?

Good detailed video. More please! lol And still waiting for the 4L80E videos. ;)

On the black transmission I see there is a oil pan with oil cooler tubes in it. Does than pan make a difference with cooling or is it for show. Thanks, keep-up the great work.

Very good info as always good sir

Shawn can you use a vacuum modulator with out a governor, to control pressure when street driven?? Thanks in advance. Keep doing what you are doing love it.

Patiently waiting for the next installing of Shawn from Mountains garage

Hi there, great content.what is different in a Cadillac 400 that makes them mushy?

I have a quick question. Rebuilding a th400 for the first time ever (first trans period).... I understand the parts about the 1-2 auto shift when holding 1st gear but why do you only put 2 check balls in? I haven't really found clear answers for that and it wasn't covered in the video. Thanks for your time!

Loving your channel, Can you tell me if its possible to have a manual/auto shift reverse pattern valve body on my column shifter? I have a 68 full size pontiac and do not want a floor shifter. What do they change to make it reverse shift pattern?

When doing this to firm up the shifts, would this require upgrading to the 34 element sprag? Or would the stock one suffice with these changes? Thank you

hello thanks for the great info, just wondering about a couple things on the separator plate the 3rd hole you said you drilled .154" will a 5/32" work or should i buy the size you mentioned, also the dual hole you plug.. if every thing internal has not been touched just skip plugging that hole "seal off the direct drum" or should that be done regardless thank you.. in advance hoping to pull mine out next week or so to play with it ..

When blocking the 2-3 Accumulator if your not running an intermediate band why would you install the piston in the valvebody again? just curious. I ditch it just wasnt sure if i should stop tossing them in the trash

Did your full manaul mods to the vb adding a cover saver with no 2nd band do I have to block any passage in the 2nd band servo

I'm trying to build a short 4x4 T400, can I go manual VB, no governor and 4l80 short output shaft? the 4x4 super short shaft is like a needle in a haystack, any ideas?

So if you're dual feeding the direct clutch should you drill the 1/16" hole in the drum even if you aren't using a transbrake? Does it hurt to drill it if you're not using a transbrake?

When doing all the modifications to go full manual is the governor eliminated as well?

Question off topic. Whats your opinion on. Cooling tran oil. Run fluid through radiator cooler than aux cooler? Just aux cooler? Thanks for your time.

I’m currently rebuilding a th400 here in Australia everything is super expensive for them I have a 36 tooth sprag and I’m wondering what you mean by grinding the flats do you mean as like a pressure relief sort of thing?

Figured out one thing for sure get a good set of taps harbor freight ones won't get it. I'm finally building my monster mountain th400

I've been having trouble with really early shifts at low mph after doing a shift kit and was thinking of just doing a full manual valve body. How does the shifter work exactly with a manual valve body? Just low=1, 2=2, and D=3?

Another great video!!! Ever do any 4l80E's? Wonder if any tricks carry over to them....

Any special notes on modifying the cadillac version? I have one with an unknown history..

I rèally love your channel so much information i talked to you awhile back about building a 421 with a stock GM block its pretty much going to be a budget build which rotating assembly do you perfer scat or eagle? And di you like the I beam or H meam rods if you were building it for yourself? I would just like your input on this.

The direct drum has two less return springs do thing it would be beneficial to put them in when installing a shift kit mild street racer. Thank you

Good info!!!

Which video has the machining of the tail housing sir. Awesome videos by the way. You are very knowledgeable with these 400s

I e been watching your videos and they are helpful! I have a question I see all the videos with the transmissions out if I need to drop my valvebody only do I have to pull the trans or can I do it with out dropping it?

Can I do all the mentioned modifications for full manual and retain 2nd gear engine braking? Thank you for all your videos currently building my own th400 based on your videos! Much appreciated.

Well, you talked me into pulling my '73 TH400 and building it. I have zero experience. I've disassembled and I'm pretty overwhelmed. But anyhow, I have 5 check balls. What might that say about this beauty's history?

Thanks for all the info...when doing the automatic shifting valve body modifications...do I leave the engine braking band out and if so can I still down shift into second on boosted pulls?

Following the video and going with the full manual mods in a early 67 8 bolt with the canister style filter. I'd like to run a deep pan and flat filter/tube. From what I can see, it appears the valve body is solid thru the area where the filter bolt threads in. Is it safe to drill and tap the valve body and if so, what thread is required? Like your style and simple explanations for us guys that haven't cracked open a TH400 since the mid 80's. Cheers.

So with grinding a flat on the pump valve and plugging the hole by the pump face in case you can plug the modulator and not have extra high pressure all the time and wear out the pump?

thanks

I'm having transmission problems. I have a 85 c30 5.7 350 with a TH400. It was running okay. Now I have noises and it shuts down when going up a slope. If someone can give me some tips that be awesome.

Have you saw a reverse man vb in a 400 that has aluminum plate no gaskets and no check balls and the plug to the right of the center support bolt has 3- .081 holes drilled in the plug. I've never seen this exact setup

Hello Shawn. Great video. Do you put the set screws in dry or do you put a little loc tite on them ? Thanks I'm advance.

Quick question....do you worry about high fixed line pressure damaging the pump in a street car? I just finished building my first th400 and ground the boost valve and plugged the modulator, along with full manual, dual feed, converter restriction etc... Also using what I assume is the stock spring (no color) and a .065 shim behind the horse shoe. I can't seem to find a clear answer on the possible pump damage. Thanks in advance

If you're only installing center front and rear bathtub checkballs, why do you suggest a size 1/8" drill for 2nd feed?? You don't have a checkball in the 2nd location and the fluid will no longer be restricted or forced through the 2nd feed hole? won't it go through the checkball hole instead and the feed will be the size of the checkball hole?

Hey. I built my thm400 according to your video. It works well. But at idle I have 185 psi in park 75 psi in reverse 185 in drive, 65 to 75 in second, and 185 in 3rd. But at 1500 rpms they all come up to 185. Is this ok. Or will cause it to fail. The 400 forum seems to think it's gonna fail. Shaun. what do you think? Looking forward to your response.......

Is the 475 stronger for racing or is it just for pulling trucks and stuff ive heard they can be a bit noisy is it worth finding one to have cuz I can get my hands on one right now for cheap low milage motor home big block it was behind

I want to retain auto features but I want to eliminate the 1-2 safety feature. Is all I have to do is grind the flats on valve and plug the hole in the valve body?

I bought that th475. Im gonna use your videos to look at this trans. I’ll let you know if it has straight cut gears or not. I know you are busy I hate to bother you with stupid questions. Do you have an email address?

Do you happen to have a stock straight cut rear ring gear for a th400? I happened to pick up a th400 that probably broke a drive shaft so the tail of the drum that goes into the bushing in the output shaft is all chewed up.

Doing my first TH400 rebuild shortly for a single turbo 5.3. My core is a 1990, which from your video may be different than the 87 down, do the mods in this video all apply for the 1990 unit? Thanks!

👍

So I can't do a kickdown on full manual

Might be sillybto ask . But on the auto shift valve body can you control 1-2 shift with the kick down electric solenoid ?

Do you have the electronic speedometer sensor for a th 400/3l80. Most were found in 88 - 90 3/4 ton trucks and SS 454 models.

I would like to know why you need to put the 2-3 servo back in the valve body when you block the feed hole

Hello, do you still need the bleed hole with the 8 & 8 springs? Thanks

Will this shift kit be ok in 1988 a th375 trans that doesn't have a not dual feed the direct?

Can I just plug the hole in the bottom of the valve body to keep it from shifting automatically when I am trying to manually shift it?

Thanks for the valve body information. If you dual feed the forward drum is there any other modifications required other than leaving the seal out?

Where do I get a solid aluminum plug with a o ring for the modulater valve?

is there a part number or link you can provide on the pump bolts you use ?

This may be a dumb question but do these modifications eliminate engine braking?

Is there a reason why you use a cup plug instead of a threaded one

I have an Early TH400 HD that looks identical to the TH475 what's the difference please

Dear sir, After a while, the kit for my TH400 GM has finally been installed and back on the car. I have a problem because gear changes are unnoticeable and i think that the transmission is ceased up in third gear. I drive at 120km/hour with engine at 3000 rev. Per minute. Even when i change gear with the gear selector in the car, it stays blocked in third. I select "L" or "I" and i may run at 120km/hour!! Do you have please any advice? Thanks a million for your helo Best regards

What book do you use/reccomend? Thank you

Teach me more man

Where are you located what state

😃😃😃😃😃👍👍👍👍👍👍👍👍👍💯

Hi man you look to have a lot of knowledge on th400 so i give you a shout my man mine is th400 full manual slam gear strong no trouble but shoot oil look to bee from the pan is that a comon thing or the cork rubber would do the job better than rubber only

Can I send my trans to you for rebuild?

So at the least you made 4000$ for 34 hr of work. I need to learn trany work!!

couldn't hear you....pass

Dead air!

Ouch, my fucking ears!

How much to build one

Hi Shawn, I want to go full manual and fixed line pressure, but I want to keep the engine braking front band. Do I do all the same mods, just add the band and apply servo in the case? Do all other mods stay the same? I appreciate your help.