Zonda 105mph pass here: kzfaq.info/get/bejne/osCJqMuHurLHqJc.html

Great information! Keep the awesome content coming!

What a good video! Thank you!

Ordered mine this morning, great info!

Secret squirrel be knowing things. Great video bud !

Thanks buddy! I would have loved to know all of this before i got my zonda 🥳👍🏼

Great info I'm not looking for a world record but maybe an 80 or 90 mile an hour boat with some sort of dependability would be great

Thanks for sharing bro! Ive subbed

I think a con with a 2 piece flex shaft in combo with high voltage system is the wiggle room or play the shaft has when it meets the drive collar, small vibrations can equate to bigger issues down the line. It happened to mine, as the flex cable turned into a pretzel and whipped around the inside the hull causing a lot of damage lol. Great explanation though 🤙🏽 1 piece for the win! Maintenance for the win!

It’s worth saying that if you get the shafts mentioned, you’ll need to: 1. Cut them at least 10.25” from the threaded straight shaft end back to the flex end. The extra length depends on if you’re running a higher pitched prop, multiple nuts like a lock nut and a bullet nut on the end. 2. You’ll have to grind/ taper the cut tip and solder the flex shaft wires. Clean with alcohol, but the heat will burn away oils & other contaminants 3. Install and make sure each side is even. Test fit the drive dog and leave a few mm space gap. Then you’ll have to Dremel the flat spot for the drive dog. I applied w/ thread locker. Great shafts though. Thanks for the info!

Thanks for the tip...what is the screw call on the runder?

How did you build your Boat shelves ? Those are perfect for my boats. Id love to put some on my wall.

Do you think I could divide a third line off the water intake to cool extra electronics? Or will it compromise the one inlet cooling system? Thank you.

Hey quick question what receiver do u recommend?? I got a flysky gt5 for it thinking it would work best but not sure if props are moving the right way with it it seem like the both running the same direction

Dear Sir, what type of, if any, reinforcements have you done to your Zonda and Zelos to survive the speeds you are pushing?

I zonda keeps tearing the liner at the top right before the collet. Also makes a screeching noise. It's greased, but maybe not enough?

Great vid real good info I saved it for future reference. Iam looking into the tfl sd just wondering your thoughts from experience if it’s worth the money. I have 2 DT E51 53”, miss geico 36” and a traxxas m41 just looking to and to my collection hoping you’ll give me some help in my decision. Thx

Great video, I ran mine for the first time this past weekend, did the one piece flex shaft and installed according to the TFL instructions, two min into the run, Destruction!! followed the instructions to the T and everything shows props turning inward, I put the Boat in the water and checked the throttle to make sure it was right, hit forward and it ent backwards, logged into the radio and reversed it so it was going forward when depressing the trigger, now I'm going to have to battling TFL to replace the destroyed parts, they already did the shafts were rotating backwards and sent me a pic of how they should be rooting and it's not the same as the instructions, now have to repair a boat with less then 2 min on it because I followed there instructions. any advise for cutting out the drive shaft support and repairing the Transit where the tube spun due to the flex cable becoming a bird nest? Thanks~

Do you lubricate the entire shaft, or just the flex? Getting a Zonda soon. Never used 2pc drives before.

Another thing to think of when using two piece or 1 piece shafts is where the load is placed on the boat. With 1 piece it's at the motor, with 2 piece it's at the strut. Which is better will always be debated. With a 1 piece you have to allow space between the drive dog and strut. If not, you you hit the trigger and the flex cable tightens under load and you would have binding where the drive dog hits the strut face. With a two piece system, the flex is able to tighten inside of the prop shaft because it floats in the shaft and not soldered. That's why they can put the drive dog right up against the white Teflon washer.

What Props would you recommend to start with for more speed, over the stock ones?.

Where I can get my shaft for my zonda i been looking on some places but am not really sure what mm are they

I like info about it im just getting into this hobby,waiting for mine to come on bangood comes 120amps seaking ,Motor: SSS 3674 2075KV brushless motor can u help me wat lipo battery to use plz ?or even wat u reackonmend ?thank u for video helpful for people like me

Hey squirrel! What props would you recommend for this boat with a stock 6s x2 setup? I wanted to know where do you get your one piece shaft from? Would you recommend a dual pickup?

For the 510B50R is the end thread reversed? wondering if I need reversed thread bullet for that side thanks man

from what I understand 4092 motors are recommended in this class. In comparison to the 3674 it adds weight and the 3674 do just fine. what is your take on bigger motors? Worth it? Or you loos agility?

How are you getting these boats to survive on 6S what am I missing? TFL North America says they will burn up, the motor’s are not rated for 6S.

What props do you recommend for the 20mph-30mph range? Just got my boat.