"8 to 12 strokes and I'm done" Me too buddy, me too 😢

That little bit when u said "listen, they sound the same." The importance of listening to your tools I don't think is said enough. Great vid

There was a guy, maybe 30 years ago, who wrote for American Woodworker. Can't remember his name. He had a unique sense of humor.... How do I know when my table saw blade is dull? If you are setting off the smoke alarms, that is a pretty good indicator!

Guess what tomorrow is? It’s sharpening day! I purchased stones a few months ago, but they’re still in the bags that I brought them home in but watching this just gave me the confidence to go into my shop and get it done. Thank you!

Thanks for putting out a simple explanation of how to sharpen tools.

Fantastic video - thank you

Quality advice and a very nice presentation…agreed, no BS

Grazie. Consigli veramente preziosi ed illustrati benissimo!

Good instruction. Thank you.

You are an excellent teacher ❤

This is the video I've needed for years.

Another great Vid. Advice is honest and relatable.Which means you get more buy in. Thank you.

This was very informative. great presentation style.

This video has been the most helpful thus far. Thank you.

Eric a great explanation of your process. Enjoy your video's. Thanks again

Followed this and was finally able to get my planes cutting real well, super good feeling!

Solid info. Good video. Thank you

Thank you very much. Clear concise and understood. Cheers

On your example I purchases a 10000 Ohishi stone and I LOVE IT!!! Thanks for the guidance.

About the chisel- the bevel on the other side pushes it into the wood. The reverse bevel keeps it going straight, opposing the small back force from the materian you're removing.

What a nice video ... eventhougt i am an occasional & semi experienced woodworker and know the subject, such a reminder is a delight !!! For beginners this video is a MUST, lucky you are. The sound of a good shaving is so nice. The more i look at your videos the more i love your style - Thanks ....

Great information, thanks for sharing!

Well done. Thank you.

Thanks for this. Your descriptions and analysis are first rate. I am having some trouble seeing things at times however.

You never disappoint my man. Always no BS, straight to the point and it is great. Well done!

Thank you! Re setting has been my hardest task!

My experience with western tools: I got the best edges grinding a "deep and narrow groove" with a dremel grinding wheel (smaller radius) that helps me freehand sharpen super comfortably forna long time. I use 1000, 3000, 8000 and 12000 stones (high quality japanese made), then japanese thin camelia oil to protect blade and tool. Always do sideways movements, also extra pressure on the sides to create that super slight curve. I got transparent shavings with lie nielsen and silk smooth finish on most woods. If I can be of more help, just ask!

Bro, I agree with stevecunningham below, you are my new favorite woodworker. You are such a patient and excellent (and oftentimes funny) teacher. Got so many questions for you bro!!

Perfect; thank you

THIS HAPPENS TO BE THE BEST SHARPENING VIDEO I’VE EVER SEEN. I HAVE WATER STONES, DIAMOND FLAT STEEL AND EVEN A ELECTRIC SHARPENING MACHINE. THEY ALL WORK GREAT. YOUR APPROACH TO SHARPENING IS THE ONE I WILL USE FROM NOW ON. THANKS FRIEND

nice. one of the better sharpening videos i have watched. thankyou.

Great video! A trick I use when flattening my water stones, which I do every time I sharpen, is to use a pencil to draw 8-10 lines across the stone before starting to flatten. This gives you a great visual indication of how flat you’ve gotten the stone. Just keep flattening until all the pencil lines are gone.

One of the best plane sharpening and adjustment I've ever seen. Thanks!

Great video thanks for sharing

Well hello dude is by far the best video on sharpening, clear and on point, it's like a master class of sharpening and set up thanks for sharing

WAUW. What an educational force you are. Watching the videos makes me dream about making furniture.

excellent video!

Honesty. Thank you.

lol, I have a penchant for 'bouje' (for short) as well. I was going to upgrade my wet sandpaper station with a water hone machine, or some good stones, until I came across diamond sets for $20. Diamond is officially cheaper than sandpaper, and my boujee shop purchases will be better served by buying some of your hand tool recommendations. Keep up the great work!

Great info! Thanks

Wow. Just incredibly informative! Especially the difference with irons vs chisels. Thank you!

Wow. I have a new favorite you tube woodworking site.

You are becoming my new favorite woodworker. Your video production is excellent and your teaching method is great!

Thanks for the great content🤓👍 9:50 My teacher showed me a method that works for me. Gently slide the top of ‘your least favorite finger nail’ across the de-burred edge. Then draw it through the end grain of a piece of hardwood.

One of the best plane setup videos along with a great sharpening explanation. Thank you.

Holy words, man. I can split hair, sharpening with a 18$ water stone (double face grit 1000/4000) purchased on the famous online shop. I love water stone.

Thank you for this!! I loved this video. Super informative. I've been struggling with figuring out the best secondary bevel angle for chisels and plane blades. Going to try 35 degrees from now on! Thanks!!!

Great explanation…your videos in general are so helpful. Thank you for sharing your knowledge!!

Pretty good tute. Thoroughly enjoyed watching. I do some things a little differently but.....

Bob Van Dyke has a good video on tuning one of those $15 guides. Doesn't take it to Lie Nielsen level, but makes it a lot better.

I use my LN Honing guide for the same reason. Love the different jaws and works perfectly for me.

awesome thanks

Fantastic advice and presentation, thank you!

From how I understand it, we Brits modified the word Camber from the Romans Their roads as most countries now do it, have a camber on them to help the rain leave the roads.

For the ruler trick you can even go to your local tool store 1000 shim, if you really cheap you can use a piece of cardboard from a cereal box it will work just as well! Or if you like me I just do a free hand, and if your back is flat that's all you need! Good video that a good tips enjoying your journey! Columbus Michigan

I check for edge imperfections by lightly dragging the edge of my finger nail along the blade edge. Super sensitive technique and less chance of laceration! If your fingernail is too short you can pull back the flesh a bit to avoid skin-to-blade contact. 40 years in fine furniture and curvy staircases. And still learning. Great video! Mahalo!

Hello, just found your videos today when searching a method of clamping mitred joins together, your video of the three techniques you use came up I watched it and consequently fell down the rabbit hole that is ENCurtis. I have spent a very engaging couple of hours whilst waiting for glue to dry watching many of them. All were very informative and seem to make the mysterious art of the carpenter accessible to us newbies, especially this little gem. Thanks for the tutorials and keep them coming my friend.

Interesting..... I do have one set of the old DMT stones, with all the holes in the plate. They had pretty much stopped cutting. Put a little of the Trend lapping fluid on them and they came back most of the way. I do have the diamond lapping plates, at least for now. Mostly I don't want the maintenance chore of flattening them. I am curious about you not stropping the plane irons. I can 'feel' a burr of the 8000 grit stone, and even off a 30,000 grit Shapton stone. I am getting back into flat work after almost 30 years on the wood lathes....

Thanks for all the tips! I appreciate you sharing your skills. Can I ask... what is the proper way to store a plane?

This was the clearest, most concise demo of sharpening and setting up a hand plane I have seen. Great video. Can't wait to try your techniques out

Thanks. Awesome detailed information. Could you advise on that small ruler you use for your back bevel? Cheers, 👍

Kudos on mentioning that there is no given surefire way to tell when a blade is dull. I work mostly with soft woods, just last week I was planing a face of a board with freshly sharpened plane. I use a wooden smother and I was getting ridiculously thin shavings (the kind that flies out straight out of the plane and starts sticking to your arm thanks to static), when I moved to plane the edge that was a bit more figured and the individual ring were harder, you could see sings of the slightest skipping on the finished surface thanks to the orientation of the grain. I waxed the sole, tried going slower, and everything went fine after that. Another thing that used to happen to me was getting fluffy (not torn out, just "fluffy") surface, but my plane still cut fine using the same amount of effort, so I thought it was weird grain, but while the plane took still the same amount of force to push, the blade was a bit duller and stroping did the trick. Time and practice solves all, thank you for another good presentation. And by the way, those stones look absolutely awesome.

Brother, when you do the ruler trick it is best to move the blade along the ruler rather than toward and away from it. This will keep the angle of the back bevel you are honing more consistent.

Very interesting!! Eric!, I feel like you're teaching me personally. I know we're all human, and we all question ourselves, but you are an amazing teacher! I would feel intimitated to work face to face with you LOL & I'm in my 50's! I wish/should've gotten into wood working 40 yrs ago. Thank you my friend, keep on teaching n I'll keep on learning...btw WHERE IS YOUR PATREON? What exactly IS a patreon lol...help...

I’m quite curious about that little planing stop mortified into your bench. Can you share some details?

As you rightly say, having very sharp cutting tools is not a nice-to-have, it’s an absolute essential for any kind of decent woodworking. As you also say, there are quite a few ways of achieving that -and a lot just comes down to personal choice. Here are a few thoughts from me When I started over 45 years ago, it was really a question of oil stones and nothing else (although my grandfather used the dried skin of the dogfish as both sandpaper and a final sharpening paper). Good oil stones are still a fine method but now there are others - and I’ve bought and tried them all I’ve got sets of very expensive water stones. You do need to keep them flattened and need to be soaked just before using. I’ve got a Tormek T8 which takes me up to 1000 grit and then the leather belt. I’ve got the scary sharp style of sharpening films. The key thing for me is simplicity. I ought to touch up my chisels and plane blades whilst using them. If I’m using them a lot, then I ought to touch them up several times during each use. For me to do that, the method has to be simple or I just don’t do it enough. So, I don’t use the Waterstones (need to be flattened and kept wet) or the Tormek (1000 grit is not enough) but use the scary sharp style of system. All stuck onto a piece of plate glass;kept on my bench and ready to use in an instant with a quick spray of water. Where I do use the Tormek is if I have to go back to regrinding the primary bevel. It’s the quickest method that I know of and it does deliver a good consistent edge. Where I do use the Waterstones is to put the secondary bevel on if I have just regrouped the primary bevel. I’m not saying this the best method - let alone the only method - but it suits my style of working. I want to touch up my edges regularly. I agree with the video in that the angle of the primary bevel is not critical. Wisdom has chisels at 25 and most planes at 30. However, I have low angle and high angle planes which vary greatly in the angles required. What I do believe is important is that the secondary bevel is about 3-5 degrees greater than the primary bevel and that I sharpen (and touch up) that secondary bevel to the same angle consistently. Absolutely hard work to touch up at 36 degrees one time; 33 the next and then 36 again. So, that consistency is key again for my need for simplicity. None of this is a critics of anything in the video. Just another perspective .

I use a strop and polishing compound as my final step. I have been told the polishing compound is effectively 15000 grit. IDK. But it does give a mirror shine to the edge.

Just brilliant! Thank you for this video, so coherent, so honest, so useful; what more can you ask of a KZfaq video

I appreciate this video. Wiping the blade dry would help to display the bevels should help in camera.

There’s a reason why so many diamond hones wear out faster than expected. People, including Paul Sellars, us a back and forth or circular motion on them. If you only ever pull the blade in one direction, little supportive ridges of metal are retained behind each diamond particle, helping it to stay in place. With a circular or back and forth motion, that doesn’t happen, and you you lose diamonds faster.

I have the LN guide and love it for the reason you mention - the long jaws. Best out there. Another one that is fairly recent is the newer Woodriver Premium guide, As good as the LN one, but no extra jaws. Does come with a setting guide and is dead simple to use and very effective. A question for you about the Ohishi 10,000 grit stone. I have had that one for over a year and was never happy with it, reason being that LN says not to soak it. It drank up water like a sponge and never worked well for me no matter how often I sprayed it with water. Recently (like last two or three weeks) I've tried soaking it permanently. The difference in use is like night and day. Love the way it works now. No issues with it and so far I've not seen any degradation of the stone. We shall see how it holds up long term. I'm wondering if you've had the same experience and have you tried soaking it?

Hey, if someone needed to do a quick hand plane sharpening/setup walkthrough, that's it right here. Waterstones, they ain't that bad price wise. I went with a DMT diamond stones they run about the same. I like the basic veritas honing guide, because it's better than the 20-30$ ones, since it's proper flat. After watching the vid, I may just add a water stone of ~10000 grit instead of the strop for some tools. A question about flattening though, what grit do you use, and does the grit of paper matter for which stone you work on?

Every project/type of wood being different, is there a basic sequence you follow in preparing a (for example a highly figured curly maple top) surface for finish (cutting/milling, planing, sandpaper grades, card scraping (?)etc etc.). Does card scraping generally go before a final sanding? Thx so much, and appreciate your teaching! Subscribed 👍

If you wouldn't mind, I could use some instruction on how to sharpen round gouges etc. Both inside and outside bevels please!

Great video, thank you. Could you share what grit sandpaper you use for flattening water stones? Also, do the ohishi stones need to be soaked?

What do you recommend for new plane irons and chisels for flattening and polishing the backs? I've always found it to be the most tedious part of sharpening. Also, does the $15 honing guide hold narrow chisels securely? Thanks you.

Awesome info, Helps . I agree sharpening is the key to woodworking. Sharp tools can let a small shop knock out alot of work and avoids dust - get a bit tired of masks not mention noise is always bad.... Out curiosity, what is your setup for creating the hollow grind? Thanks..

Just curious what is you system for establishing the primary / hollow grind bevel. Thanks

I inherited my grandad's planer and the back handle is loose. Do you have a video of how to overhaul the whole thing? I am a beginner here!

Oishi stones are just iminishi stones rebranded for lie Nielsen. Save the money I've had both find there to soft and require to much flattening

Can you answer a question regarding soaking your stones? You pulled them from the tub of water, is that where you store them, or prep? If prep, how long?

The difference in sharpening angle is usually dictated by 2 things; the type of metal the blade is made of, and how often you want to sharpen. To explain why this is; The more carbon a metal has, the harder it is. Thus it's better at keeping it's angle. I.e. high carbon steels can hold a sharper edge than lower carbon steels. So if you'd sharpen a lower carbon steel with the same edge, you'll be sharpening more often because it will dull quicker.

I’m going to try the bigger jump in grits. I’ve been doing 600-1000-3000-8000 but maybe I’m over doing it?

I've watched about a bajillion videos & read a bunch of articles on how to sharpen. This is by far the best I've seen. Tons of information and practical tips. Usually,the techniques are taught but not explained in as much detail. Thanks for this video.

Camber ; a slight convexity, arching, or curvature (as of a beam, deck, or road) : the convexity of the curve of an airfoil from the leading edge to the trailing edge. : a setting of the wheels of an automotive vehicle closer together at the bottom than at the top.

Having spent a ton of money on sharpening…my setup now? I have 3 stones: 1K, 3K, and 13K. I use all 3 when I flatten the back of chisels. The ruler trick is a great trick and use on my bevel up planes. I sharpen by hand and do the secondary bevel by feel.

Think of camber as the top lean in and out of a tire. If it's leaning either way the tire gets round on the edge.

Thanks for the video! I wonder how many talented people give up on woodworking, or waste a lot of time and effort, to complete the project, due to blunt tools. These whet stones using water have to be soaked at least for 24 hours, before use! Or kept wet constantly. Without a good soak, the stones could be worn out of shape! Or they might require replacement! Placing the emery paper on a flat piece of granite or a piece of float glass sheet will be good for chisels! And also levelling the stones!.

Hey Erik, going back through the library refreshing my wetware with the information provided. I just purchased a couple Ohishi waterstones, going with the 1K and 6K based on the instructional video provided by CFC. Maybe I'll get to 10k some day :) How do you store your waterstones when done sharpening?

21:54 do you have experience with Tormek or similar sharpening systems? If so, why do you prefer the stones and manual sharpening?

Etymology. From Middle English chambre, borrowed from Old French chambre, from Latin camera, from Ancient Greek καμάρα (kamára, “vaulted chamber”)

Since it's a very small angle on the back bevel, a good approximation of the angle is the tangent of the angle, so the thickness of the ruler divided by the distance to the edge. Assuming a 0.5mm ruler and 3cm distance, that gives us an angle of 0.0167rad, or about 0.95 degrees

This is all well and good IF you've got a decent iron edge to start with. This video is great, but consider doing one using a completely trashed iron 😅 Good job man, it is informative

My old dad - passed away over 30 years ago - used only wooden planes, but the blade sharpening followed that which you suggest in your video. He also trued his stone in a similar way. The only difference was he used a square of 1/4” thick plate glass, which he claimed was flatter than a billiard table. Nice video. The preference for a 35 degree edge is interesting: my Stanley plane blade has a 30 deg. angle and it can snatch at times….

I've noticed folks seem to keep their waterstones in big honkin' tubs of water. Is that necessary, or could they be happy in a smaller container? Thanks for sharing!

How long should you soak the water stones for before using them?

Do you store your water stones in that water bin or just soak before use?

The ruler trick is not an issue for plane blades, I think it gets a bad rep because of chisels. If you want to use the flat face of a chisel, the back bevel can prevent it from cutting. Ah, ok, you mentioned it later in the video...

What if you could sharpen even faster and get them 3 times sharper for a fraction of the cost? Would you try it? Serious question :)

another question, with LN honning guide(long jaw pair)can you sharpening the spokeshave blade to 25°? or only 30°