Especially a workbench! Why do these folks always work on the ground? What a ball breaker. They're always squatting, doing everything on the floor, no stool to sit on, nothing.

@@kentlange5338 its cheaper, and they are used to it, seldom few tabels out there

@@kentlange5338 at least he doesnt have open toe shoes on like all the other videos of these guys.

Facing with such a long overhang, shows some lack of basic instruction.

I dont think he needs them, he's doing alright as it is.

That's total bullshit this guy would be more than capable of running modern up to date equipment. If he had a lathe AND a mill, he could be producing precise and accurae parts en masse. In fact at the end they show the whole shop which does have some real equipment.

Very true… nothing wrong with that o would say. However technology will catch up and hopefully he will adapt.

Alhamdulillah.. thanks father ♥️♥️

Then you have not seen a lot. All the shown techniques I have been using as well in the 1980s. And he has a quite well equipped shop. Your snooty remark about true accuracy only shows how inexperienced you are. You better shut up if you don't have a clue.

@@Herr_Bone Sabarlah kawan. Tersenyumlah untuk hal yang tidak mengenakkan hatimu.

gracias señor.. saludos a la familia de allá.. 🇦🇷

I think he was making a variable Carbide Holder motion mechanism. Then used in making crankshaft on lathe.

Tornada Silindir malzemelerin içine veya dışına pratik olarak yag kanalı açmak için

Thanks Frank ♥️

I will make a tool sir.. less a few more steps this tool will be completed

It's a sex machine. He's gonna put a Dildo on it

Thanks sir ♥️

I'm from Indonesia sir.. India in our country is famous for Bollywood stars ♥️♥️😍

Thanks sir

T

Он и сам не знает что это и для чего 😂

kzfaq.info/get/bejne/b6uAmbWVnJ-qgIE.html

Terimakasih pak..salam satu laras dari Jawa Tengah

@@Yantoo Larasati teman saya

After watching several lathe videos where a wire is used for measuring runout, I tried it myself. You'd be surprised how close you can get with sharp pointed wire - probably within +/-.001" if your eyesight is good. Also, when you crash the wire into the part, no big loss. This technique is now my goto when chucking long work pieces, especially if they have a rough surface.

@@5tr41ghtGuy sorry, even with eyesight like a hawk you couldn't get it within. 010" if the wire touches on the part it would have more than. 010" of deflection before you could even tell , and there is nobody that has eyesight good enough to see .010 " runout from more than a couple of inches away and using a magnifying glass . I guess that's why the dial indicator and micrometer were invented. Use a large tip on your dial indicator when checking parts with rough surfaces . That's why the dial indicator has screw on tips .

@@russellhopper6925 the whole point is that the wire doesn't touch the part; rather, as the tip of the sharpened wire approaches the surface of the part, the way light responds exaggerates the gap. A similar thing happens when you place a straight edge across a flat part, and hold it up to a bright light to check the uniformity of the gap. For the lathe I use a sharpened brazing rod myself, and I've made a simple block to hold the rod in my toolpost. As a round workpiece approaches concentric about the lathe's spin axis, I move the cross slide in so the tip gets closer to the surface. On another note, if you can't see .001" runout by watching the end of a faced round part while it spins on the lathe, you need go get your eyes checked.

@@5tr41ghtGuy I guess you didn't really read my message. My eyes are fine . As for the straight edge technique, it doesn't do anything to the light until you get close to .001" of an inch , then the light will turn a bluish color as it starts to eliminate all the other waves of color and blue is the only wave length that comes through the gap . I guess if it works for you, continue on .I'll stick with the accurate metrology tools for a better outcome .

@@russellhopper6925 Give it a whirl and report back.

Suwun mas e.. mergo warahane jenengan iki

@@Yantoo Lokasi bengkelnya di mana Bosku,...?

Nggawe lubang oli mas e

I'm from Indonesia sir

@@Yantoo great,, do you know kratom

Kratom in my area is the name of the plant that is often used as traditional medicine, sir..

@@Yantoo yes.. i use it every day and get it from your country. I used Kratom at first to get off opiod pain meds. It is a great medicine.

working on the floor has become a tradition in my country sir 😁

Что бы это не было, оно не пахнет СИНХРОФАЗОТРОНОМ!!!

Ini hasil akhir bang kzfaq.info/get/bejne/b6uAmbWVnJ-qgIE.html

😁🙏

But this doesn't matter for what he is making. You build for the tolerance you need, or am I missing something here?

@@jrrt6745 iF one is going to do a job, it is worth doing it to ones best ability If the person operating the lathe had slowed the rpm down, There would be no resonating to cause chatter, as you can see in the bored hole.

Anu mas e 😁

Merci Monsieur.. pardonnez mon erreur, j'apprends à utiliser le français via internet.. 🙏

@@Yantoo Une langue un peu inutilement difficile... si vous arriver à modifier le titre..

i need this tool to hire me..

What is it used for?

What is up with your comment? Watch the rest of the videos in the series. This cuts oiler grooves for plain bearings. Incredibly useful.

My apologies.

I think that the bigger problems are 1st that we have convinced ourselves that this is not even possible without a CNC machine; and second that even with appropriate safety equipment a lot of this might not even be possible for a business in many states because of liability and regulations

🙏