The Proper Way To Run Wheel Spacers on Your Mustang!

Рет қаралды 7,053

Күн бұрын

Yes, wheel spacers are safe (for the most part). Well, it really depends if you both install and maintain them properly. Find out the difference between different wheel spacers & wheel adapters, what hub-centric and lug-centric mean, and how to install wheel spacers on your vehicle.
Get Steeda 1" Hubcentric Billet Wheel Spacers here:
www.steeda.com/steeda-mustang...
Steeda 20MM Hubcentric Billet Wheel Spacer:
www.steeda.com/steeda-s550-wh...
Steeda 1.25" Hubcentric Billet Wheel Spacer: www.steeda.com/steeda-s550-wh...
Steeda 1.50" Hubcentric Billet Wheel Spacer:
www.steeda.com/steeda-s550-wh...
Subscribe: bit.ly/Steeda_YT
Shop Ford performance parts at www.Steeda.com!
---
www.steeda.com
Steeda Performance Vehicles
www.steedavehicles.com
Steeda UK:
www.steeda.co.uk
Steeda Europe:
steeda.eu.com
Pinterest:
/ pins
Facebook:
/ steedaautosports
Instagram:
/ steedaautosports
Twitter:
/ steedaautosport
TikTok
/ steeda
0:00 Intro
0:15 Types & Their Uses
1:14 Bolt-On Wheel Spacers
2:42 Spacers for Square Fitment
3:30 Hub Centric vs Lug Centric
4:30 Slip-On Spacers
6:25 Wheel Adapters
7:00 Installation & Maintenance
8:49 What To Look For When Purchasing
9:47 Trimming Factory Wheel Studs
11:46 Outro

Пікірлер: 12

@ZuluJomama 5 ай бұрын

I ran stock wheels with spacers for a good while before picking a set of aftermarket wheels. Definitely recommend going with aftermarket wheels without spacers if you can fit it in your budget. Riding with spacers on normal roads around me definitely added harshness to my ride. At first I thought it was my other suspension parts I had installed but after removing the spacers and replacing my stock wheels with aftermarket wheels, my ride quality improved so much. I was running 25mm spacers in the front and 23mm in the rear.

@freedom6919741 5 ай бұрын

Great education video as always !

@donaldbrown1300 4 ай бұрын

Good Job!!!

@GR018 4 ай бұрын

Good video. 👍🏻

@damoose4229 5 ай бұрын

Think it's worth noting that S550 and 650 Mustangs with Magnaride have different wheel stud lengths on the front and the back. If you're going to run a spacer on the front watch for the stud length vs the pocket relief on the back of the stock wheel. ;)

@1slow5point0 5 ай бұрын

I can agree on the adapters. I had 2-piece adapters on a 1/2 ton Silverado back in the day. About 10 miles from home the left front adapter sheared the bolts off and I lost the wheel at 60mph.

@rynev3392 5 ай бұрын

I recently had bad luck with some cheap bolt on wheel spacers. They had cheap soft metal nuts that held it to the factory studs, they rounded off when I used an impact or breaker bar when I tried to remove them. Since they were recessed into the spacers, I ended up having to buy new rotors and wheel bearings to get them off. Let’s just say I wasn’t happy with the previous owners for installing them

@peterwho9380 5 ай бұрын

Rule of thumb is that if you are using just spacers DON'T go past 1/8-1/4 inch with 5 full revolutions and you'll be fine. Depending on my wheel setup, I have 2 sets of hubcentrics 3/4 & 1 inch and 1/8 & 1/4 for just spacers for every type of scenario. Don't forget to buy your hub rings for your standard spacers or your aftermarket wheels to prevent doing damage to your hub!

@paulferka4696 5 ай бұрын

@steedaautosports can I run your bolt on spacers as slip ons? By removing the additional studs. Obviously with extended studs in this scenario

@steveclemons4729 17 күн бұрын

Haven problem putting my 15 in.front runners on my foxbody it got a 5 lug conversion with cobra brakes any help would be think ful

@vicrefalo3273 4 ай бұрын

I'm contemplating about installing a set of 20mm billet rear hub centric spacers on my 18 mustang. I've heard that after installation, I may encounter wheel bearing problems? What is your opinion? Your feedback will be appreciated.