The Ultimate Tao Tao 50cc GY6 Troubleshooting Compilation (No Start, Bogging Out)

Рет қаралды 163,432

Күн бұрын

UPDATED HD VERSION. WITH CONDENSED STEPS FOR MORE ADVANCED MECHANICS
• The Ultimate Tao Tao 5...
Watch In HD For Diagnosis of No Spark-- see below for links to diagnosis videos.
Quick and Easy Steps. Your chinese scooter won't start? Or does it die when you give it throttle? This is a condensed version of the process by which I figured out the problems with my friends scooter. Not saying yours will be the same, but these are good steps for anyone diagnosing scooters to run through. Also the information compiled on this page will keep you from scouring youtube and the forums for good information. One thing I did not mention is that I did do a valve adjust, but it didn't help me with my scooter (valves were near spec). However, I have read and I do believe stuck exhaust valves can be the problem for many people experiencing performance issues.
If you aren't getting spark (do not fear) look for links below about how to diagnose the issue. Most common problem would be CDI or Coil failing. Luckily on these scooters parts are very cheap, never a bad idea to have an extra part or two in the trunk compartment in case it decides to quit on you.
0:00 Introduction / Description Problem
0:20 Fresh Gas / How to Remove Seat and Battery Access
1:25 Checking for Gas at Carb / Fuel Regulator Explanation
1:55 Where Vacuum Line for Fuel Regulator Was Pinching on My Scooter
2:10 Checking for Flow of Gas through Fuel Regulator (Disconnect Line at Carb and Turn Engine Over)
2:42 Checking for Spark. Make sure ground spark plug, key on, kill switch off. For instructions on how to remove spark plug see video-- • How to install a spark... You can use tool kit provided with tao tao, use screwdriver inserted through end of socket to remove spark plug. Do not overtighted upon reinstall (use anti-seize).
3:23 Checking for Intake Leaks and Dirty Carb. Use Carb Clean not brakleen. Brakleen won't actually run scooter and may make it die, carb clean should act as a fuel where spraying it directly into the rear of the carb should allow the scooter to run. I don't care about people saying this is bad for the scooter or the carb, sorry but these are cheap chinese scooters-- get a life.
4:21 Where to Spray Carb Clean to check for intake leaks / dirty carb
4:36 Most Important Spot to Check for intake leak. Replacement part
www.ebay.com/itm/50CC-GY6-SCOO...
5:48 Final Thoughts & Outro
Supplemental Videos:
Here is how to adjust your valves--
• Highly Detailed GY6 Va...
Good thing to do when starting scooter cold, pump the throttle before trying to start (if you have accelerator pump to push more fuel in the carb)--
• How to start your scoo...
adjusting and setting the idle--
• How to adjust the idle...
how to unseal stock carb (must do before attempting to clean)-- good idea to order a new unsealed one and mess around and unseal old one. That way you have a replacement if anything ever goes wrong.
• TaoTao ATM50-A1 Chines...
If you have no spark and want more diagnosis steps for the ignition system--
• KidNme GY6 Troubleshoot &
• The Ultimate GY6 Start...
To clean the carb (if a kid can do it so can you) Many other videos on this and all the same principles apply--
• KidNme GY6 Air filter ...
If you have no fuel while applying vacuum at the fuel regulator either buy a new one (after making sure vacuum is adequate) or replace with manual petcock.
to replace fuel regulator with manual petcock and fix potential flooding of intake manifold with gasoline due to failed regulator check out this video--
• TaoTao ATM50-A1 Chines...
More about fuel regulator / how it works--
• Taotao ATM150-A Evo sc...
Also what can go wrong with fuel regulator where it lets gas back in through the vacuum line-- flooding the engine and causing it to die at idle-- • My chinese scooter won...
The carb I bought--
smile.amazon.com/Carburetor-St...
Spark plug NGK C7HSA
Inline fuel filter i used--
smile.amazon.com/Wix-33001-Com...

Пікірлер: 156

@JayCras 7 жыл бұрын

I want to add that two of us spent a day + trying last year to get this "thing from hell" going and I frankly just gave up. Everything you pointed out was "wrong" The downhill hose wasn't, The carb needed to be blasted with cleaner and that input hose was so loose I thought I was turning a stripped screw to tighten it. I just did this stuff one thing after the other and it was ready and working in short order. You really made my day so thanks for doing what you do.

@grazz7865 3 жыл бұрын

Good video. One thing to note-empty a whole can of carb cleaner if you have to. Keep the factory carburetor if you can. The aftermarket carburetors are actually worse. I went through 3 of them. Eventually rebuilt the stock carburetor and put it back on. Runs great now.

@radconserv68 5 жыл бұрын

That's a good tip about having an air leak after the carb, going into the engine. I had never thought of that before. Thanks for the vid!!!!

@plainclothesprofit6255 4 жыл бұрын

Dude YOU ARE THE MAN! Tighten up those intake hose clamps. Fixed my scooter in 10 seconds. Thank you thank you thank you

@JayCras 7 жыл бұрын

Loose intake and dirty carb. Hosed it with carb cleaner and tightened the input and all I can add is YOUR THE MAN!

7 жыл бұрын

Thanks these comments make it worth it to make these videos. :)

@JayCras 7 жыл бұрын

Just an update. Its all still working great! The neighbor with the other ride from hell is going to try following your advice. He really had some wild problems. He got it running for a day then the next time out gas pouring out all over the place. *He was tempted to throw a match on it what with the trouble he has had.

7 жыл бұрын

yeah sometimes these scooters can be a huge pain the a**

@jessieyaz5430 5 жыл бұрын

I watched 100 videos and yours is the best THANK YOU!!!

@howardcurtis4150 9 жыл бұрын

Thank you you jogged my memory and fixed my 3 week long problem of a no start,,, do not overlook the intake leak from the head to the carb.

9 жыл бұрын

Howard Curtis thanks one of my first videos. Hoping to get better and less long winded. Thanks for the like !

@angelmalloy5451 8 жыл бұрын

I have a 2014 taota0 which I brought last summer. It stop running towards the end of the summer. I have been trying to get it back running since December, changed everything to keep it from bogging out and nothing until I came across your video and low and behold I AM UP AND RUNNING AGAIN- IT WAS THAT LOOSE AREA YOU SSPOKE ABOUT THANKS A MILLION!

8 жыл бұрын

+Angel Malloy glad my video could help :) thanks for the support

@eastendsteve 7 жыл бұрын

Max's Garage any ideas about a front wheel shimmy? More like a knot in the tire kinda feel. Like I'm going over bumps in the front fork

@mikemartinusa 9 жыл бұрын

Great video! Will have to try these steps. Was having a no start problem which turned out to be a carburetor. Now the problem I have is that the scooter will run fine when it is first started and I can get up to 32 mph but as soon as I let the throttle back any it bogs down and can get 12 mph max. Let it cool down 30 mins and will work fine again for 2 minutes.

@michaelangelo9871 5 жыл бұрын

Thank you very much you're awesome brother One Love I just bought a Verano and it's bogging out I'll use what you taught me tomorrow in the morning I don't work tweaker hours One Love

@crpth1 7 жыл бұрын

Hi Nice video. Good approach to some of the most common issues. Just one note on a small detail it's a "vacuum operated fuel petcock" or valve in short, has On/Off position no pressure regulator capabilities. Thanks for sharing.

@edwardjames6070 Жыл бұрын

gotta admit, you're a pretty good mechanic. you DID leave some things out that I don't think you should have.

@thedrumsndthebeat 6 жыл бұрын

worked for me. this engine looks identical to my Manco hornet. thanks!

@wincar311 9 жыл бұрын

Dude, awesome video...thanks, been wrenching on my two Tao Tao 150's for hours, watched your vid and started both in 10 min. Intake leaks, who knew...

9 жыл бұрын

wincar311 thanks man glad to hear! I definitely spent many hours trying to figure this out, and my experienced friend was just as confused.

@kerryloftus3619 5 жыл бұрын

You fixed my issue, stupid air leak!! Thank you!!!! Your awesome :)

@FrenchieFries 5 жыл бұрын

Ok I got mine to work got a new carb. My problem is I can get it to idle but when I add throttle it starts to die on me. So I can’t drive it. I don’t know exactly what it is but everything seems sealed. I was having a little trouble getting some gas pressure at first now I got it... hmmm this is like a puzzle tbh

@DINOHarlemrdthave 4 жыл бұрын

Good job Max. Thank you for the info.

6 жыл бұрын

Thanks to everyone who left me feedback! It takes a lot of energy to make these videos, but reading comments where it helped someone get their problem fixed makes it all worth it. Have a good day!

@NikkoG 6 жыл бұрын

Keep It Up!

@Unknown-hl7sb 5 жыл бұрын

Max's Garage I have the same moped, 2012 taotao 50cc atm-50a1 I believe is the model, my issue is in having no response at all from my electric start, it has no ignition on it, removed the key and lock and bypassed it. The issue in having is that since if had it I've rode it twice, moth times we've had to jump the starter. My question is, could it possibly be a bad solenoid? That's keeping the starter from getting signal? At one time I could unplug both wires to my electric start, touch them and then I could hear the starter solenoid clicking, no response from starter tho, only seems to work when we jump the starter. The scooter is something I got from a friend for cheap and I'm guessing it was just to big of a mess for him... As it is being for me... I'm having a real hard time finding an exact fit for a wiring harness as I'd like to completely and properly replace all the wiring, there's been to many snips and reconnects for me to feel like wiring is not the problem. I've got an ignition and key and that will go on, but until I can find a new harness... Any kind of help you can suggest? Pleaaaaase help if you can!!! Lol thank you

@radconserv68 5 жыл бұрын

@@Unknown-hl7sb It could also be a faulty brake switch. My electric start would do nothing when I squeezed the front brake lever. I finally tried the rear lever and it worked!

@Unknown-hl7sb 5 жыл бұрын

@@radconserv68 ended uo being a bad selonoid

@radconserv68 5 жыл бұрын

@@Unknown-hl7sb Good to know. Thanks.

@Dragnmastralex 9 жыл бұрын

"not gonna cover no spark because there are plenty of videos on youtube about it" searches youtube for no spark... this video is the only one that comes up... way to go!

@TheOVERMUCH 9 жыл бұрын

***** What if my fuel flows without starting?

9 жыл бұрын

TheOVERMUCH you have spark?

@TheOVERMUCH 9 жыл бұрын

TheOVERMUCH The line from the gasfilter to the carb flows without starting or doing anything.

9 жыл бұрын

TheOVERMUCH go through the steps in the video. I don't really understand what problem you are having. 3 elements you need for starting: fuel, spark, and air. Get a bottle of carb clean and spray it through the back of the carb if you have spark

@TheOVERMUCH 9 жыл бұрын

My problem is, I'm getting gas in my floaterchamber but it won't go via my sparkplug to my cylinder. I think it has something to do with my fuelpomp/vacuum thing. Not a TAO btw.

@jguild45 9 жыл бұрын

Intake was the problem. Thanks.

9 жыл бұрын

jguild45 thanks glad it helped :)

@twilli8118 7 жыл бұрын

Thank You man your the king of bikes

7 жыл бұрын

just hope it helped :)

@stevenmullins3496 4 жыл бұрын

Great video!

@joea4501 Жыл бұрын

Great, thanks for posting 👍

@bstchaves6602 3 жыл бұрын

Great video boss very helpful

@thedaydreamer7972 2 жыл бұрын

Good video, 3 things to get a engine to pop, spark, fuel and compression,,,I have bikes that good spark and fuel, but tested very low compression, rebuild top end or fix compression issue and you are good,,,test the spark first and foremost, its the eaisiest,,,,,,if you are supecting fuel, remove airbox and hit it with carb cleaner into the intake,,,,,, bike does not start, keep it simple and test those 3 things first,,,99% of the time if you address all of those the bike will at least start,,,,,,

@1deucenasty 8 жыл бұрын

thanks for the video

@someguystudios23 8 ай бұрын

For me, the spark plug was loose. Put some never-seez on it cranked it hard, and it runs beautifully.

@MyBuford 8 жыл бұрын

I have a 2015 tao tao. Ran good until today. I ran the battery down trying to get it started, so while it was on the charger, I sat and thought about what could be wrong. Small engine, first thing to check is the plug. (learned this when I was a kid mowing yards) Pulled the plug out, it was black and gas soaked. Cleaned it up, used an emery board on the electrode, put it back in, fired right up. Gotta get a good plug for this thing next time I go to town.

8 жыл бұрын

+drone pilot always good to have spare plugs , glad you got it fixed

@lordxavious 8 жыл бұрын

awesome informative video. very helpful man

@rdgturbo2507 8 жыл бұрын

my kids quad bike was bogging down on acceleration I just found a bad connection on the safety cutout switch it was sparking nothing like working in the dark to shed a bit of light on the problem lol anyway rewired the kill switch and sorted it now thanks for your video ;-)

@NikkoG 6 жыл бұрын

haha! What a coincidence! I bet for once you were happy to be "disadvantaged" in the dark !

@33pastas 5 жыл бұрын

amazing car on the back.

@giovannireices678 7 жыл бұрын

Have a 2014 tao. Have to to hit the gas and give stay giving it gas or it will shut off also before that happened the scotter kept going fo rears even when I let the gas go. But I'm going to try everything tomorrow, I appreciate it the video was very helpfull.

@giovannireices678 7 жыл бұрын

I meant forward not rears. :)

7 жыл бұрын

also be sure to check updated version of same video, and read in comments for more links to helpful videos. kzfaq.info/get/bejne/qdSCrbKQ3K24ZJs.html is updated version. Start with checking intake leaks, then if not intake leaks, clean carburetor, check spark plug, and go from there. best of luck

@sammcgee813 7 жыл бұрын

Qué Onda Productions

@firehoney4445 4 жыл бұрын

Going out to do this right now

@brianlowks8301 5 жыл бұрын

I decided to open up my speedometer case up to see how the miles tracker and speed cable make the orange needles turn but after reinstalling it on my scooter the needle for the speed no longer moves it is literally stuck and wont move unless I push it with little force and I'm thinking that it may just need some lube since I woke the thing apart or something, any thoughts on a fix ?

@missael773 5 жыл бұрын

Hi my Tao Tao racer 50 took a fall 2 days ago due to heavy wind, while parked out on the street. It starts up fine but once I come to a complete stop it shuts down. Any ideas of what I need to look into ? I'm using premium gasoline on a mid 2018 Tao racer 50.

@victordavila3005 8 жыл бұрын

hey man, i have a 09 kymco 50cc agility. it starts up, and runs for about a min. and cuts right out. can you help me with this problem. thanks man.

@audratreat7831 2 жыл бұрын

I have a 2020 49cc Vespa and know what my prob is now but forgot where all the hoses went , Diagrams dont help me much, can you show me?

@nando4755 3 жыл бұрын

So what was the peoblem with yours !! I have spar ! I have fuel !! Runs for a bit and bougs out !! Yours had an intake leak ??

@tomfrederick2444 9 жыл бұрын

Where can I get one of those - I know a mechanic! Nice job Max - great quality.

@bepilc 6 жыл бұрын

Need to compress left brake level to start on my 49cc ToaToa.

@sandradeeowens399 10 ай бұрын

One of my 50cc Tao Tao scooters will not go at top ordered speed. Won’t go above 30mph. Help?

@filippocunsolo9647 4 жыл бұрын

I have 02 Yamaha Zuma and everything comes on but it will not start up i need help

@ProfessionalDad 5 жыл бұрын

ADJUST THE VALVES. I replaced carb and CDI due to bogging out with no results. I finally checked the valves. The exhaust valve was too tight.

@thomasflynn642 8 жыл бұрын

I put a cone air cleaner on 50cc scooter,what do you do with the 2 lines that went into the stock air box?

@radconserv68 5 жыл бұрын

They may just be air pollution hoses, which are worthless and don't affect anything. Not sure, but I think so.

@kissimmee244 9 жыл бұрын

Having trouble dude crank but wont turnover what do you think the issue is it started for a second and it shut off seconds later. So i was wondering since you seem like such a cool guy could we set up a private tutorial phone call? Or you send me some pointers.

9 жыл бұрын

sears woods Definitely a fuel flow issue or a carb issue. Follow the steps for checking for gas at the carb, and then spray carb cleaner directly into the carb. If it starts with the carb cleaner being sprayed in then you know intake leak, or dirty carb. Luckily carbs are cheap and carb cleaner is cheap. Go throug the steps in the video. Also, make sure it is clean fuel and gas is full.

@warn1ng854 4 жыл бұрын

I just bought a new 2020 tao tao 50cc and it keeps bogging out when i give it gas. i will have to try these steps. Fingers crossed.

4 жыл бұрын

as long as gas hasn't sat forever and isn't bad and it really is brand new, I would skip to checking for vacuum leaks and then making sure spark plug gap is good and spark is strong

@fashionstreet1 5 жыл бұрын

Hey Max great tutorial video I have been having a bit of a problem with my gy6 150cc Chinese scooter Eagle I replaced the motor which is now brand new i recently been having a problem with bogging down while riding at high rpms and it would bog down and completely shut off while I'm riding it and giving it gas full speed but It starts right back up it just boggs down??? Any suggestions would help?

5 жыл бұрын

Baqash Ahmath sounds like could be a fuel pump problem. Otherwise you sure there are no vacuum leaks?

@fashionstreet1 5 жыл бұрын

@ I doubt if it's the fuel pump because this is a brand new motor I installed two weeks ago and I don't know if it could be a vacuum leak I haven't checked it I guess that's a good place to start I will check that as well and I will keep you updated! Thx a whole lot!

@fashionstreet1 5 жыл бұрын

I also replaced the new stator with my old stator because the new one that came with the new motor is not working my headlights and taillights but when I installed the old stater all the lights are working so both stators differ slightly in center width but the same the new stator is not the original from the scooter!

@timothyjohnson5833 2 жыл бұрын

I have a tao tao 50cc gas electric scooter it will started up but won't stay running its got a new carburetor fuel line and filter

@apelectric4137 6 жыл бұрын

Hi Have 125 Cc taotao can't get it to start Has spark Carb is clean and clear What else can I check? Please Thanks

@rhyslanouette5086 6 жыл бұрын

A Peker is the fuel getting into the carb

@TobiBallLikeKobe 6 жыл бұрын

I put the carb cleaner for the first time and it worked the first time when I turned it off and tried starting it back up it didn't start

@rhyslanouette5086 6 жыл бұрын

Romulo Gomez happened to me I just got a new carb stator and now runs brand new

@DeadLetterOpener 9 жыл бұрын

First thing you wanna do is spill a shite load of fuel everywhere...second thing you wanna do is make a shite load of healthy blue sparks around the general area you just spilt fuel. :D Just kidding, had to laugh...great video mate. Maybe just put a warning up for really really slow people, that they should wait a few minutes for the fuel to evaporate before doing the spark test...or just do the spark test first to be on the safe side.

@NikkoG 6 жыл бұрын

haahha Right on! I agree, I can see a lot of "need it quick" kind of people hurting themselves

9 жыл бұрын

kzfaq.info/get/bejne/qdSCrbKQ3K24ZJs.html updated version, more condensed, but mostly same information. Including link to new video about vacuum fuel pump on gy6 150cc

@braiannahuel6648 8 жыл бұрын

I recently purchase the very same Scooter 50cc 2014 taotao black the same one from the video I had a situation that wen I was driving at 40 miles per hour the Scooter lost all the speed I was literally driving 5 miles per hour on the intersection hahaha what happen was that my Neibhor told me that it had a brand new carbonator. but he haven't use it in over 4 months and it only has 800 miles I seen some videos but I'm not sured what could be

@buckmajor 8 жыл бұрын

+Qué Onda Productions Hey mate, I have the same problem unable to start the bike. The battery is fully charged so it has to be something else. Could I use starter fluid instead? If so, where do I put it? Newbie here.

8 жыл бұрын

Optimus Prime yes you can definitely use starter fluid. use same steps as video, check for spark, check for fuel, then spray fluid looking for intake leaks. If scooters starts while spraying starter fluid into carburetor then you know a) you have spark b) the engine still works c) carb is either dirty, you have a vacuum leak, or some other issue related to fuel air mixture

8 жыл бұрын

use common sense as starter fluid is very flammable. have a fire extinguisher handy and don't get your face near anything that could ignite (like the fluid after spraying it into the carb)

@buckmajor 8 жыл бұрын

Qué Onda Productions Thanks Que, I will try it in the morning and see how I go. Will post back hopefully with good news. If carb is dirty what do I do? Still trying to learn how to use the tools and stuff.

@anthonydicicco6714 4 жыл бұрын

ok, so first of all thank you for this video, definitely helps narrow down the issues. Now, i checked the fuel lines and im getting fuel to the carb, i checked the spark plug and im getting spark, i checked the connections for the intake at the manifold and at the airbox and made sure they were tight, still no start. i removed the intake boot and sprayed carb clean directly into the carb, still no start. im out of ideas. any suggestions? thanks in advance.

@anthonydicicco6714 4 жыл бұрын

also, i replaced the fuel filter, fuel regulator and all of the fuel and vacuum lines and still nothing.

@carnynja9966 4 жыл бұрын

Basically. If you’re spraying carb clean directly into engine and it has compression and spark it WILL fire. No ifs ands or buts. So go do that again and make sure it is carb clean not brake clean although that prob will work. Then I would start with easiest- replace plug. Sometimes you can’t see a bad plug. Gap new plug. Use ngk or denso. Then double check spark again. Then make sure scooter has compression (I would think you have checked that). You can have air fuel spark with low compression and you’ll spend your whole life trying to get it start. Cheers hope that helps. Carb clean direct into carb removes all fuel components. You’re left with a problem with spark, compression, or timing. 👍👍👍 also, never think just because you checked something you checked it right or it’s not actually just a weak spark etc. keep at it

4 жыл бұрын

CarNynja yes^

@anthonydicicco6714 4 жыл бұрын

Ok so I double checked all of that stuff again and still nothing, I took the carb apart and cleaned out the jets and got it all nice and pretty but still nothing. And funny story, I don’t actually know how to check for compression 😅 how would I go about that?

@anthonydicicco6714 4 жыл бұрын

another update, i dont have to tools to check compression but from all the other videos ive watched that seems to be a pretty common problem as well so i went ahead and gapped the valves to 0.003 intake and 0.005 exhaust, thikning this is definitely the problem because when i opened the valve cover, the rocker bars were stuck so tight there was no gap whatsoever. so like i said i gapped them, put it back together and still no start. i have to be missing something or doing something wrong because now im fresh out of ideas...

@kevinthorn9672 4 жыл бұрын

Ay so i just replaced my carb and it wont start up if it does it wont stay running shuts off?

4 жыл бұрын

literally go through the steps in this video

@kellihankins5707 8 жыл бұрын

when I go to start my moped it makes a buzzing noise and will not start. Help

8 жыл бұрын

+Kelli Hankins No idea:)

@gabeathouserules7910 4 жыл бұрын

Are you pressing the starter button or the horn?

@tinsterfish5906 5 жыл бұрын

I got a loose hose and can’t find where it connects to

@tinsterfish5906 5 жыл бұрын

There’s 3 hose that connects to a black cylinder that’s just there not attached to anything

@shadowboxing1729 4 жыл бұрын

Im taking it out but it looks like the manufacturers glue it in?

@maxfrederick1244 4 жыл бұрын

what?

@chambliziOfficialChannel 8 жыл бұрын

chinese gy6 vs genuine honda who owns both let me know

@kevinbeck9459 6 жыл бұрын

Chamblizi The All Mighty! I have both a taotao an a Honda met taotao is still going the Honda is not running only has 200 to 400 miles on it

@dixieboy5689 3 жыл бұрын

>>> 2:35

@wincho11 7 жыл бұрын

My scooter tao tao wont start with the electric choke, only by the kickstarter. Can anyone help me?

7 жыл бұрын

Need more information

@olddirtyburt7522 7 жыл бұрын

try bypassing the starter solenoid, typically located on the right side. Follow the wire from the starter back towards the battery, you'll run into it. You can also see if the starter will turn over by applying 12Volts directly to the lug on top of the starter.

@tugspeedman4729 8 жыл бұрын

I bet you get good weed lol

@NikkoG 6 жыл бұрын

hahahahaa

@NikkoG 6 жыл бұрын

I still subscribed though. I accept it. Good knowledge too.

@toddkirkland6542 4 жыл бұрын

@@NikkoG all right

@chonkers3180 8 жыл бұрын

hi, my scooter starts, then runs for about 5 seconds tops then dies, this is only with no accelerator. after about 5 start, idle, die it will not start again. so i pull the accelerator 5 times or so, then i try start is again and it starts second time and runs for about 5 seconds any advise?

@chonkers3180 8 жыл бұрын

+Charlie de la Cour it was running fine earlier that morning

8 жыл бұрын

+Charlie de la Cour low gas, bad electronic start, vacuum leak

8 жыл бұрын

+Qué Onda Productions choke*

@Miquinn Жыл бұрын

Bro my shit just won’t start at all bro and I don’t know what’s wrong with it

@deathincarnatesplace 7 жыл бұрын

imagine a tao tao motor put on a bike frame???

@simoneubanks6976 6 жыл бұрын

my speed wont go past 30 mph. any idea why?

@rhyslanouette5086 6 жыл бұрын

Simon Eubanks what cc is it?

@simoneubanks6976 6 жыл бұрын

49cc. if thats the regular speed then screw it.

@rhyslanouette5086 6 жыл бұрын

Simon Eubanks that's the max speed on it

@deathincarnatesplace 7 жыл бұрын

do you know how to get 50 mph from a 50cc motor put it on a bicycle frame and run the transmission to the front front. then use a gear shifter and the rumor is you get 80 mph.

@deathincarnatesplace 7 жыл бұрын

i heard if you switch gears without even reving the motor only turn up the carb so it will roll at a little higher than idle it will make you 200 miles per gallon. but hey someone prove it.!!!

7 жыл бұрын

sounds really boring to ride

@donnamcconnell7498 8 жыл бұрын

what if your seat won't lift out! I removed all the bolts and it would not come out, all the screws and bolts mentioned were removed

8 жыл бұрын

You have to remove the screw in the frontonhinge

8 жыл бұрын

I really don't know what could be holding it but just really try to yank up on it and then feel where it's catching and look for a bowl or some kind of screw something and just take that out and then see if that helps or not

@shannonprice5705 5 жыл бұрын

Where's ur helmet mister? ;)

@happygilmr 8 жыл бұрын

yeah let's spray Carb or brake cleaner in the Carb and burn the valves

8 жыл бұрын

+happygilmr yeah lets be a troll

@MyBuford 8 жыл бұрын

+Qué Onda Productions Do you by any chance have the plug models for alternate plugs? Champion or NGK, really doesn't matter, just something other than stock.

8 жыл бұрын

+drone pilot no but i just search ebay and alternates will come up

@MyBuford 8 жыл бұрын

Did that, it should be here middle of next week.

@kongenisinghetto2327 8 жыл бұрын

not a great idea checking for spark right after you spilled gas all over the engine LOL ive done that mistake on my lawnmower it got on fire funny asf

8 жыл бұрын

+ESCvideos2015 yeah you are right, hopefully people can figure that out for themselves. I didnt even think about the proper sequence as I figured it´s common sense. Plus gas evaporates real fast, you wouldn´t be watching youtube videos if you worked that fast.