THE ultimate VESPA PLUG & PLAY pnp TUNING tutorial

THE ultimate VESPA PLUG & PLAY pnp TUNING tutorial | FMP-Solid PASSion |

Рет қаралды 93,919

FREAKMOPED Vespa Tuning | FMP - SolidPaSSion |

7 жыл бұрын

guide for 177 & 210 pnp tuning. all u need2 know about: carb - cylinder - piston - ignition - clutch & si fuel supply - fuel tap - fuel hose. simply follow the guide and there is nothing to worry about :) ------- BIIIG enbarassing MISTAKE at 2:37, so SORRY guys! idle mixture screw of course: IN=LEANER and OUT=RICHER! ... ------
will add another short vid to correct it!
carb settings pnp tuning with 5&8mm bores in the airfilter:
177: 160/BE3/122, 160/55(2,9)=screw 3 turns out
210: 160/BE3/125, 160/55 (2,9)=screw 3 turns out
these are the correct settings for si carb based on many many engines. theay are all the same! IF this doesnt work with another engine, there is a problem and the engine not healthy.
ie: IF the idle Jet needs to be leaner = bigger than 2,9 the engine is sick, it could have an oilsucker for instance and/or a crank that doesnt fit the rotaryvalve pad (bigger than 0,05mm tolerance) NOT A SINGLE healthy rv si engine needs an idle Jet leaner than 2,9 as it is for the original 200ccm setup and we do what? Tuning! so it HAS2BE richer of course!
--------------------------------------------------------------------------
like what u see? u can support FMP via patreon:
/ freakmoped
--------------------------------------------------------------------------
like what u see? u can support FMP via patreon:
/ freakmoped
_____________________________________________
DISCLAIMER: the information shown in this video, is about THIS specific hardware. it is my personal observation documented with this video. It DOESNT automatically mean, that all such parts by this producer or seller do have or will have same issues.
_____________________________________________ --------------------------------------------------------------------------
FOLLOW me on
insta: @FreakMoPed
fb: / freakmoped
--------------------------------------------------------------------

Пікірлер: 50

@StoneCut 7 жыл бұрын

Screwing the idle jet mixture screw IN makes the mix LEANER and not richer.

@FreakMoPed8 7 жыл бұрын

omg, did i really mix it up?!? HOLY SHIT! uuu thats really BAD and embarrassing, LOL thx stonecut for that tip. f*** so its also wrong in the short video, shit happens... will add a comment. thx again!

@FreakMoPed8 7 жыл бұрын

replaced the extra video and included a infocard in the pnp tuning guide. thx mate for the info!

@bertiedoonerwind8061 4 жыл бұрын

@@FreakMoPed8 wondered why my T5 just Chernobyld!

@xterrared1 7 жыл бұрын

The fuel filter cap rubbing against the carburetor case is a great tip! Thanks for making these videos!

@FreakMoPed8 7 жыл бұрын

:) u are welcome! its the biggest mistake piaggio produced, annoying so much People around the world and nearlly no one even pro workshops is Aware of it. watch here the extra Video: kzfaq.info/get/bejne/bdRyfdNmts3ScoU.html

@owengune 3 ай бұрын

Great video, helped a lot.

@inspetorgambiarra 7 жыл бұрын

Hello, I live in Brazil, I have a 200cc wasp that only has one admission window, is it possible to rework this cylinder with two more windows? Do you know of any tutorial on youtube that can open more windows in the cylinder? I anticipate my thanks.

@FreakMoPed8 7 жыл бұрын

kzfaq.info/get/bejne/grmEadygzKnedac.html

@inspetorgambiarra 7 жыл бұрын

thank you mista.

@robertofernandez5310 7 жыл бұрын

exelente explicasion

@bertiedoonerwind8061 4 жыл бұрын

Great video!!!! 2:43 Is that the 2.5mm drill bit widening the main jet hole? 7:01 is the arm/lever on remaining oil pump cut down? 11:03 image of top of modified piston. It appears to have some minor abrasions/figures on the top? Is that all? 14:04 you say but no OGM? what is the OGM? The smoothing of the ports in the cylinder and piston,( what do you use as your guide for specific enlargements?) is that similar to the work that the worb 5 guys would have done to the Malossi 172 cylinder and piston to make it perform to a higher level? It would be great to see your interpretation on a Malossi 172 kit.? I could send you one to do? ;)

@FreakMoPed8 4 жыл бұрын

yes / no / duno, need to check / OMG = "bgm" and is also sold by sip. / the t5 172 malossi does need some love yes.

@bertiedoonerwind8061 4 жыл бұрын

@@FreakMoPed8 thanks mista, would the porting and smoothing of the pistion on the 172 malossi be the same also.

@FreakMoPed8 4 жыл бұрын

11:03 image of top of modified piston: thats my FMP signature ;)

@papanicc88 Жыл бұрын

any tuning recomendations for 177DR kit with polini box? thanks in advance and greetings from greece!!!

@FreakMoPed8 Жыл бұрын

exchanging against vmc 177 superG

@esencia78 2 жыл бұрын

If I have matched 24 mm carburator and casing and I would like to reinstall a 20 mm carb, what could It occur then?

@FreakMoPed8 2 жыл бұрын

no problem

@seansimpson2586 5 жыл бұрын

can you shave fins off malossi 166 to keep auto start?

@FreakMoPed8 5 жыл бұрын

Yes u can

@rclavier 7 жыл бұрын

hello.. what did you suggest for polini 177, as clutch cog and primary cog? thx

@FreakMoPed8 7 жыл бұрын

hy romuald. pnp runs fine with 68/23 and further tuning (timings of cyl and inlet Timings of crank 75°) the 65/23 is a musthave! everything else is too short and throttles the engine really bad.

@rclavier 7 жыл бұрын

hello!! thanks for your answer.. my cases are untouched, just polini 177 21/65 si24 and bigbox sport.. i just want to imagine if 21/65 is the only good thing? you make great job!!

@FreakMoPed8 7 жыл бұрын

so weired, i only see ur 2nd comment on Google as an alert but not on KZfaq... and the button answer doesnt work... grrr so its a plug and play polini 177, then u take 22 or 23 cogwheel for the original 68 Primary. only 21 is too short, u loose Performance with that. the bbS is the totally wrong exhaust for your setup sorry to tell u that. bbS need proper inlet- and cylindertimings (75° crank and even 10° overlapping, and 120/176 cyl) to work well, otherwise it performs worse than a siproad, bbt or polinibox, These 3 are the right exhausts for your setup as u only have 45° inlet timing with the original crank, no adjusted side ports in the case, and Timings below 170° with the original 177 kit. get a polinibox! :) "romuald clavierhello!! thanks for your answer.. my cases are untouched, just polini 177 21/65 si24 and bigbox sport.. i just want to imagine if 21/65 is the only good thing? you make great job!!"

@rclavier 7 жыл бұрын

ok thanks, what do you mean by "polinibox"!!

@rclavier 7 жыл бұрын

which kind of dremel do you use?

@adwinoraeshad7091 7 жыл бұрын

what is the purpose of removing the walls on the air filter?

@FreakMoPed8 7 жыл бұрын

more air flow. the less an engine can breath the less power he will generate.

@FreakMoPed8 7 жыл бұрын

+adwino raeshad more air for the engine.

@nikolastonic96 7 жыл бұрын

Where can i contact you to get some tips for my engine ? :)

@nikolastonic96 7 жыл бұрын

Yep now i know one of my problems the rotary pad is f***** mesaured it at 0.1 probably its even worse.

@FreakMoPed8 7 жыл бұрын

go2my Facebook page ie: de-de.facebook.com/freakmoped

@FreakMoPed8 7 жыл бұрын

try the rv trick while Assembling it. 0.1 should be okis, but with si carb u already see and feel the effects

@LW91 3 жыл бұрын

Remember, if you remove anything matching cylinder and case, is not p&p anymore.

@FreakMoPed8 3 жыл бұрын

definitions are dynamic, for me pnp is NOT opening the engine, just exchanging parts from the outside, some small adjustments dont change the basic just external work. call it "pnp advanved" or "pnp FMP style" 🙃 i can not mount ie a 24mm carb onto a 20mm casing hole, thats just wrong. It would be doing things without love (and thinking) thats why i of course adjust these things on hand which are easy solvable

@LW91 3 жыл бұрын

@@FreakMoPed8 as you say in the words "plug and play" , it will consider something that you take and mount on the engine. And most important of all, if you want to come back to the original form you can do. Try to do the same thing with modified case, I don't think it will work. Anyway I'm just saying this only because the word p&p is wrongly used. The work you did it's very good, keep going.

@FreakMoPed8 3 жыл бұрын

thx! maybe wrong in your definition, not in mine. it still fits cause the engine stays closed no need to have the same opinion here. "pnp advanved" ;) no worries, original 200cc cylinder ALWAYS works, why? simply cause it only has 1 real port, the other 2 are closed fake ports = they dont care if the case is not adjusted cause they are closed anyways AND simply think the other way round: when pnp without case modifying is possible, why should replugging the original cylinder not work? its also just simply pnp tuning same with 177, even when the case is adjusted an original cylinder will always works its a tractor engine.

@LW91 3 жыл бұрын

So is worth If I want to put a 177 polini without matching the cylinder with the case ? I know that the power it's a lot less. 60% for the p&p without porting

@FreakMoPed8 3 жыл бұрын

always port, even when its just pnp ;) ;) no polini 177 is in general not worth the money. loveless update as with the 210 with the still same old weaknesses for decades. pnp not much more power thatn a cheap DR 177. i would take a vmc 177 for pnp

@adesunarya5557 4 жыл бұрын

Please translate in indonesian

@FreakMoPed8 4 жыл бұрын

quite difficult as i dont speak indonesian ;) guess english is international and fine.

@adesunarya5557 4 жыл бұрын

@@FreakMoPed8 I can not speak english

@bertiedoonerwind8061 4 жыл бұрын

@@adesunarya5557 www.google.com/search?q=google+translate+indonesia+english&rlz=1C1GCEA_enNZ861NZ865&oq=google+translate+indon&aqs=chrome.0.0j69i57j0l6.8779j0j8&sourceid=chrome&ie=UTF-8