You have never seen a laser like this- SRWOR 10 watt

Рет қаралды 7,281

Жыл бұрын

My latest machine for testing, this machine has a 400 X Infinity workspace, assuming you have enough cables. The SRWOR self propelled 10 watt machine.
Ali Express link to machine: s.click.aliexpress.com/e/_ol8...
Amazon PROMO code for 6% off: www.amazon.com/promocode/A1TD...
For templates that I have made, check out my Etsy shop. I build files for projects and tools for laser engravers.
www.etsy.com/shop/TheClackShack
For Clack Shack shirts, check out my store:
the-clack-shack.creator-sprin...
The links below are affiliate links that will direct you to the product in this video. If you use this link for a purchase, I will receive a commission from the purchase. I remain unbiased and honest in my assessment as always.
The Clack Shack on Amazon= www.amazon.com/shop/theclacks...
My XTool affiliate link:
www.xtool.com/?ref=TheClackSh...
Comgrow: comgrow.com/?sca_ref=2392321....
Monport 40 watt CO2-
monportlaser.com/collections/...
Discount code: Clack6 (6% off machines)

Пікірлер: 42

@knitsewfancy Жыл бұрын

Can't wait to see what you do with this laser! What a cool laser!

@TheClackShack Жыл бұрын

I have some ideas... we will see

@MarklTucson Жыл бұрын

Interesting design. Very clever approach and the autofocus is a neat feature. Seems like it does have limitations, the dust you pointed out on your table is pretty common to the working environment this is going to encounter. Overall quite interesting. Will be interested to see what you do with this in the future.

@TheClackShack Жыл бұрын

You know I have plans.... lol

@stevedonalson5675 Жыл бұрын

The Laserpecker 2 has a travel mode as well. It can slip like this one, but has brass wheels and is more prone. Nice introduction.

@TheClackShack Жыл бұрын

Thanks, it is a cool design

@josephbaechler1840 Жыл бұрын

Very interesting. It should have a fixed skid plate or alignment rollers on one side and follower rollers on the other to help self centre on those 10’ runs to keep the alignment

@TheClackShack Жыл бұрын

It has dual rollers that are about 3 inches wide. It also has a linkage connecting the two sets of rollers. I do think I may build a riser/ guide for it though

@minnesotamaker1846 Жыл бұрын

I can see a "Guinness World Record" for longest continual engrave in your future. 😉

@TheClackShack Жыл бұрын

Might have to try

@stephenbagshaw4301 Жыл бұрын

I’ve been watching quite a few videos regarding the use of XTool laser machines and I’m quite interested, so I’ve purchased the XTool 20W. I’ve been watching quite a few of your videos and I was wondering wether you have a video regarding your laser positioning jigs which includes dimensions and machine settings, this would be a great help to get me started. Regards steve

@TheClackShack Жыл бұрын

Custom engraved ink pens- the easy way kzfaq.info/get/bejne/r6xnrdGgydfaoJc.html I have lots of videos on how to use them

@DaBalloonGuy67 Жыл бұрын

Looks good but for the price, it might be worth it. The length is comparable to the GlowForge. The width is comparable to the xTool. It would be nice for making big signs to glue onto another piece. How does this work with Lightburn or is it compatible?

@TheClackShack Жыл бұрын

It works with lightburn and is capable of crawling as far as you want. I only restricted it to 800mm. I could engrave an 8 foot long board with long enough cables.

@JackInTheShop Жыл бұрын

That is crazy.

@TheClackShack Жыл бұрын

Yea, the real crazy part is that it actually works pretty well.

@jontucker370 Жыл бұрын

Could you set it and burn a long straight line and then use the line as a reference to set your long material

@TheClackShack Жыл бұрын

I suspect just framing would be sufficient, I plan to find out.

@attainableaudio4533 7 ай бұрын

Did you end up keeping this or...? I can get a pretty good deal on one but not sure about the longevity, any more info would be appreciated. Thanks

@TheClackShack 7 ай бұрын

I have it, just not many uses in my shop.

@johnmeyer5402 Жыл бұрын

Is there any possibility of using air assist or do you think it’s even necessary?

@TheClackShack Жыл бұрын

It seems to be using the vacuum as a reverse air assist. It pulls air up through the hole from the bottom. Odd but seems to be working

@johnmeyer5402 Жыл бұрын

@@TheClackShack that’s different. Thank you.

@anitaseiber6335 Жыл бұрын

Are you using Lightburn with this machine?

@TheClackShack Жыл бұрын

Yes

@abedlalkhawaldeh580 Жыл бұрын

what machine you suggest for me as abiggner laser machine

@TheClackShack Жыл бұрын

Get limit switches and lightburn compatibility if possible. Budget dictates the brand. At least a 10 watt

@jakerazmataz852 Жыл бұрын

Cutting a cylinder, or something tall, looks to be a problem.

@TheClackShack Жыл бұрын

It does have it limitations. But also has its advantages.

@larrycolson7451 Жыл бұрын

Great video again introducing this machine Dave, but not impressed with the consistency. I can see this for a bar top or long signs, stencils or coffee tables as in other videos, but not something very versatile for craft or home use. Just my opinion.

@TheClackShack Жыл бұрын

I agree, that’s why I said it is a task specific machine. I see where it would be good to have for some jobs but not my pick for all around use.

@deenawillis1597 Жыл бұрын

Hey, I went to a laser presentation class tonight. The instructor said that I needed to have a laser license on any Class 4 laser. If I didn’t have this license I could be fined up to $170k. Have you heard anything about this?

@JackInTheShop Жыл бұрын

I guess I am going to be in big trouble. LOL

@TheClackShack Жыл бұрын

What kind of presentation? Never heard of that. Maybe if you are using it for medical use.. You always need to ask what law they are referring to. If you plan on doing an outdoor laser show, the FAA has guidelines. I am sure he was talking about something other than a laser engraver.

@DaBalloonGuy67 Жыл бұрын

Most of these are class 3 lasers I think. But I could be wrong.

@TheClackShack Жыл бұрын

OSHA has some laws but not finding anything about diode engravers. I look good in Orange any way. LOL...

@deenawillis1597 Жыл бұрын

@@TheClackShack me too!! Thanks. I just thought it was odd. I know for a fact that if you are using a medical grade laser for laser hair removal you do need a certification of completion for the laser course and laser safety certification. Thanks.