No video
How to Program the Feniex 4200 Datalink Controller
Рет қаралды 20,225
Күн бұрын
@KannonRomano 5 жыл бұрын
I wish the fusion interior light bars could be connected through data and have the option to dim
@nameless4917 2 жыл бұрын
Could you show how to create a button to change the flash patterns of the lights?
@UltraBrightLightz 2 жыл бұрын
I will have that video added to the list!
@brandonrennix1163 4 жыл бұрын
Can you upload an audio file for the siren?
@UltraBrightLightz 4 жыл бұрын
Sorry you are unable to do that
@08_crown_vic Ай бұрын
Is there a way to set the lights on the controller to be only red, not green?
@UltraBrightLightz Ай бұрын
I asked our Feniex Representative and he said that you should send an email to:techsupport@feniex.com and they will be able to assist you
@08_crown_vic Ай бұрын
@@UltraBrightLightz apparently they said it's not possible
@oldschoolscannerbuff 10 ай бұрын
Can the slide switch be used to turn the head unit on?
@MikeBizzaro 10 ай бұрын
Yes, this is possible
@austinblackburn7260 3 жыл бұрын
My newer model Feniex 4200 traffic advisors lights on the controller is not working how do I get them to work? They were working but now they are not
@UltraBrightLightz 3 жыл бұрын
It sounds like there is an issue with the controller but Feniex Tech Support will be more then happy to assist you.1-800-615-8350
@YZracer110 5 жыл бұрын
How do you program this for non-feniex traffic advisors? Mine is 8 head negative switched. Help would be appreciated
@jjones6725 4 жыл бұрын
I had the same question. Apparently this data link unit does not offer the negative outputs for the traffic adviser. It will only work with Feniex traffic adviser through a RJ45 cable. The older process units which have a clear cover, has the negative outputs for the traffic adviser built on the side of the process unit. You can see this in older pictures and videos of the 4200 setup. So in short no the data link does not offer negative outputs for off brand traffic advisers.
@LeskiStation 6 жыл бұрын
Was looking for info on how to program the traffic adviser with this software, all i can seem to find is left and right arrow, no mention of center out and cluster warn features. Also my bar was built with work lights, and i do not see an option to enable that in the software.
@UltraBrightLightz 6 жыл бұрын
Activating both the left and right arrow will preform center-out. Rear work lights should be activated by flood or one of the modes
@someguy9873 Жыл бұрын
The ignition wire has to be programmed to a button? Or it will turn on automatically with the vehicle?
@UltraBrightLightz Жыл бұрын
It will turn on when the vehicle is turned on
@oldschoolscannerbuff 6 ай бұрын
@@UltraBrightLightz is it possible to use one of the buttons to turn the unit on? if so how can this be done?
@MikeBizzaro 6 ай бұрын
@@oldschoolscannerbuff If you have the controller connected to constant power or even to key on, if you press one of the buttons, the light connected to that button will activate
@timmc6836 5 жыл бұрын
Can you explain the time feature? Is it possible to have it do a traffic arrow for 3 seconds then switch to warning mode for 3 seconds ECT?
@UltraBrightLightz 5 жыл бұрын
Hi Tim, The timer function allows any button to continue functioning for a set period of time after it's been disabled. Timer can be set for any duration between 1 second to 1 hour. This applies for all inputs A-H and all buttons. The slide switch cannot be programmed for timer or momentary functions. The momentary function only applies to buttons and allows a button to activate only when the user holds the button down. It will not remain active once pressure is released.
@adaeljflores3047 2 жыл бұрын
GREAT BUTNTHE MOST IMPORTANT QUESTION IS DO I NEED TOHAVE THE 4200DL ON OR OFF WHEN TRRYING TO PROGRAM BECAUSE MINE IS OFF CLEARLY AS I CANT HAVE BOTH WIRES LUGGED IN AS THERE IS NO ROOM SO THIS DID NOT HELP ME AT ALL IF YOU DONT EXPLAIN IF THE UNIT NEEDS TO BE ON OR OFF.
@UltraBrightLightz 2 жыл бұрын
Feniex does not say in the instructions if the unit has to be on or off but it does say that the ignition wire does have to be hooked up in order to controller the attached equipment
@yoyoyolo-kf3qi 2 жыл бұрын
So is there anything in there to control quad lights, like a bottom activates red or another will turn them to amber?
@UltraBrightLightz 2 жыл бұрын
It depends on the quad product. Most quad products require the converter to change color on the quad. Unless you have the Feniex One in which case it would all be done through the software
@yoyoyolo-kf3qi 2 жыл бұрын
@@UltraBrightLightz Alright thanks
@UltraBrightLightz 2 жыл бұрын
@@yoyoyolo-kf3qi You're welcome!
@KnightRider1983 5 жыл бұрын
Skipped a part I was looking for. Where do you plug in your USB at??? I dont see a port on the unit
@UltraBrightLightz 5 жыл бұрын
It is on the side of the unit.The USB cable that comes with the 4200 controller has a regular USB port that goes into your computer and on the other side is a specific size port that plugs into the 4200 controller
Ultra Bright Lightz
Рет қаралды 4,3 М.
Swatara Warning Lights
Рет қаралды 7 М.