Nice restart Rush, also the drop thru shows the consistency of the weld 👍

The master at work.. Great job Rush.

Thanks for showing both sides of the weld

Going to have to try a flex head. Never used one yet. Looks helpful

OMG that is art! Da Vinci welding! This planet needs you kid!

Chill blocks are your best friend when welding thing Aluminum.

Supah Cleannnnnn

Love that file man, works great! Exquisite job as always rush! Love how you give shout outs to people in the community that all contribute towards a better and more enjoyable tig welding and fabricating experience. Speaking of, I will probably hate you up about making that ring after the holidays, Then upgrading a few things around the shop and of course taking care of Christmas and what not lol Peace brother, Keep Blazin!😎🤘

Beautiful weld.

Beautiful weld. i love the fact that you make your dabs look like "teardrops" rather than "halfmoon" like. super sexy stuff.

Never leave home without my TIG finger😁😁😁

Should do a semi clean one and compare them I do alot of boat props any recommendations or tips ?

What settings were used? so as what Tungsteng filler did you used? awesome work !

The only Person who knows how to deliver with a Gas lense! How much flowrate for a Nr. 5 with a lense? I am a standard 5 collet body guy for years

When I try to do the same thickness aluminum plate, my very first firing melts the aluminum. And I've tried reducing the amperage so low that it doesn't weld at all then. I have yet to weld 0.065" aluminum. 0.125" I can usually start getting welds to work, but it too doesn't look very good.

Awesome work.how or what are you on time % an back ground settings for thks thin.i am trying to get welds like that on 3003 .064 thickness .could you please share your your advice

3:35 No apologies needed. This view is actually preferred half of the times. There is nothing much to learn from a super close up at x4 the speed that you see on 95% of the videos out there.

RAW.

I highly recommend a flexible body file and holder you will love it there abit sharper than your average file but you get used to it and you can get all different tpi files and just swap them out great for any sheet metal plus you can curve the file in both directions or use flat

Beautiful work as always! :) Are you using 4043, or 5356 filler?

really nice weld mate , very hard to make better it's perfection but i woul'd normally make it with stainless steal on the inside

What frequency settings do you use??

I’d like to see you do some 063 and 080 aluminum, I work with that lots and sometimes struggle.

Hello my friend. I just started tig welding and triying to weld thin aluminium pipe. I have to clean and everuthing but just by tacing it i burn through. I believe i have the amperage and freaquensy wrong. Can u tell me wich is the best? Thanks

help, i cant weld two small cylindrical tubes together, what should i do

Hi Rush, your welding skills are amazing. I'm very much a beginner. Would you mind suggesting settings for a basic machine for butt welding 1.2mm 1050 aluminium please? Like cfh, electrode size, ceramic cup size, stick out, amps. I can't change frequency or do pulse on my machine and I'm really struggling! Either seem to melt back edges or not enough penetration. Plus no foot control 🤔I can't really use a chill block as I'm welding up hammer formed body parts on my car (perhaps the metal is thinner as a result of the forming?) Best wishes, Christian, England.

é necessário limpar ou cortar a ponta de vareta de adição como fazemos com aço inox na parada de mudança de posição da tocha? excelente soldadura.

Who has polished alum. material? No oxide removal? If one should file or remove oxide do you still think you NEED acetone wipe down??

Settings?

I am a future aspiring welder and your work is phenomenal. But since this is a video on eliminating impurities from the work piece as much as possible, this is my two cents worth from the aerospace industry.... Once you've wiped down the work piece, because your hands have impurities and oils on them that you're transferring right back onto the work piece, it's highly recommended, unless you're allergic to them, to wear nitrile rubber gloves. Also, acetone will leave an invisible film if it is allowed to evaporate dry. And acetone evaporates fairly quickly. So, in addition to wiping the piece down with a clean wet wiper, it should be immediately wiped down with a clean dry wiper before the acetone dries and repeating this process until both wipers remain absolutely clean from any residue. Lastly, acetone is some nasty stuff where the use of proper personal protective equipment should not be an afterthought nor overlooked. Hint: Nitrile rubber gloves are not enough protection when using acetone and it will destroy the gloves. Instead, there are special acetone gloves designed for this purpose. Be safe and happy building!

Fun fact is that while in the U.S.A. 2 mm are considered "thin", in europe thin material is

For us its thick 😅 Thin is less than 2mm or less than 1mm 😅😅😅

Leave your text up longer on your videos.

Thanks for showing the backside..

Don't let OSHA see this..no gloves, no file handle, no labeling of the acetone bottle..siserich macht frei!🤣

i need to stop being so lazy and prep material better!!