Where i live in Australia, he who tolerates the flies is usually the winner lol.

Good score man...!!!,I buy used motors for the same reason,and on the raining days I build what I call Frankenstein motors out different parts,a d I got some motors that are not legal to race but they are fast an it fits my budget,......✌

Dope video rajaa. Learn lot from this video thanks Brotha

Great break down bro awesome video

That’s how it’s done ✅ great info brotha thanks 🙏 i think I was looking at this same engine good to see it went to a you bro 😎👍🏾👍🏾💯

Now i want to get an engine to tear down and rebuild thanks for the inspiration!

Bro Always good info here like Always, awesome job brother

Another great info vid..thanks brother

Rajaa thanks for another great video but typically most bearings are damaged during the removal process because they are removed by pulling on the center race of the bearing which puts incredible lateral forces on the entire bearing this is why all bearing manufacturers or OEM's will always tell you to discard a pulled bearing.

Great video! Keep it up!

Steel wool on my dremel 120 grit and all that rust be gone🤟🏼 and while it’s rotating it helps the ball bearings rotate as well either sideways or back-and-forth spraying either fuel or alcohol or even marvel mystery.

Rajaa you know you the man baby great video bro 👍😤

Your Videos are so Good🔥🔥i Can watch it all day Long 😁

Sup fam pest control looking good on the track 💪🏿👑

Motor looks good! I don’t have any experience with these FX motors but they do look promising and from your videos that I’ve seen it looks like they boogie also! I’m not sure if you were able to ever try a old Werks motor B5 is one of my favorite go to motors that I buy whenever I see used ones out there that still have somewhat of good compression and or not beat up but I’ll buy those relatively cheap and use them till there’s nothing left😁

Appreciate the video. Basically going thru all your vids. Getting real close to pulling the trigger on a nitro buggy Question or your opinion. Is there a engine easier to work on or service than others? Or basically all the same? Thanks again.

Your videos er so helpfull. Keep them comming. 🤘👍😎

i rebuilt a reds r5r, i was bummed out when i did everything by the book and it barely idles....then i found out my fuel got bad. so i guess check the fuel too.

Great vid on the used engine this is why i buy knew unless i know the person an they take care of there stuff.well for a buck you have sum knew parts at least caise im sure a buck you wouldn't of got a whole engine an its what you like fx great vid

You coming down too ga this weekend for the Phil Hurd race at loganville rc complex

Lmao at the intro bro 😂 great video and info tho.. looks like you got a good deal on that motor 👍🏼👌🏼

Big bro you had me rollin 🤣 good vibes and knowledge always much respect always KING RcFam4Life TRUFAM4LIFE BROTHERS4LIFE 🤜🏽🤛🏽🤝🏾🤴🏾✊🏾💪🏾💯🏎

Good shit, you brought her back to life. 😁 That's awesome you got a great deal on the engine. I didnt know there was a race coming up. Are you getting notifications from RC Signup, or just checking out where they are? Let me know? Thanks bro!!! 🤛

Great vid as usual. How do you know if a front bearing is bad? My nova 28-8 is having rich conditions even when it’s warms up meaning I’ll getting A ton of smoke and it sounds gurgley. It will run fine for a few then start to stutter. Sad thing is it’s a fairly new engine, just broken in.

How do you get the bearings out. My hpi 15ss is the same way.

👍

At 14:04 you can see, that there is a little spot on the crankpin. There is no dlc coating on this spot. At my fx engine, it is the same. Is that normal wear?

Avid bearing company has good prices,you can get a bearing kit for your car&motor

💩 bees 🐝😂😂😂 very informative man I hate buying used nitro engines I only buy them if they’re no longer made nice vid 😎👍🏾👊🏾

Ok my guy, you gotta go to the dirt bike store or auto store, and pick up the k&n airfilter oil cleaner. It's in a black spray bottle, that is the best stuff iv ever used for carbon and to clean the inside of my engines, I promise you, that carbon will fall off, no scrubbing required. Give it a shot.

Great 👍🏻 info on engines bro. Keep the content rollin.. “F**King bees 🐝 and shit” lol 😂 ima also pick up an FX soon lmk where is best place to purchase a new one.... thanks.

Damn bees and sh!t 🤣🤣... I feel your pain brother

👍🏾

I'll run it just send it my way. Lol looks like you got a great deal on that!

man I am allergic to bees I look like a bitch swating and dancing around lmao love the vids man thank you for all the good knowledge

What you use to pull your bearings?

Nice track where is this

How did you take out the bearings? Is there a proper procedure??

Bruh how did you remove them bearings

Lol. Whoever built the track next to the pond lol. That water is a fly magnet

Got damn bees #BANGBANG

Damn bro I'm gonna send you my motor

Maybe he was running pespi max rather than nitro.

Remind me to NEVER use a stand near the water. H.F.!!!

I know where you got that motor from bro lol

That thing seemed kinda slow...

80USD for that engine used.....bargaaiiiiiiiiin!!

Hahahahaha fucking bug...Lol