OEM Quality superior service thanks Red!

After the clear coat fully cures remember to wax the headlights a couple times a year. Stops the yellowing and fading all over again

Good job! This is the correct way to do this! If anyone is curious, you can get 2k clear from your automotive paint supply. They are happy to sell it in a rattle can! Best wishes!

I'm glad you didn't skip re clearing. Thank you

The only person ive seen that can actually paint making one of these videos

Finally, a 'life hack' that isn't bogus, this is legit how most car body shops restore headlights, not a click bait, this is genuine, one bit of advise I can give, is make sure the Clear Coat you use on the headlights when you spray them has UV protection in it, this will help against this ever happening again, as its the sun's UV that causes the 'Yellowing' and 'Hazing'that causes the damage in the first place, just helps to avoid this from happening again, if not, once the paint has had time to dry and cure, and has had several hours to dry hard, give them a gentle final polish with a very fine finishing wax that has uv protection, not anything which has cutting compound or you'll undo all this hard work 👍

It looks really good! Big difference for a little bit of elbow grease.

Nice blaster sidekick you got there! 🤫

Ive done this without taping, wrapping and plastic with only 1000 grit on a farm vehicle, the lights were good as new without all the unnecessary steps

Nice,now I’ll just have to do it inside the lamp too

Quick and straight to the point, thank you so much! Also use some UV headlight protection polish as this helps against future yellowing :)

this is a very good way to do it but honestly i dont see any reason to not just use the sylannia kit at my autozone. pretty much the exact same process and end results but without having to mask off the whole front end because you dont use a spray can.

Wow I was always hesitant about sanding my headlights but now I will definitely do this. Is this 2k clear coat?

That’s a lot of work but that’s what happens when you see that finished product!!!🔥🔥

My man thats clearer than my future

Depends on the car model, but it's probably easier to just take off the headlights

"Kobe"s commentator failed to mention you need 2k Clear coat spray. Other than that very detailed informative video. Thanks. I'll use a buffer.

Finally, someone who does it right! Fantastic job

Looks great! There are no “permanent” fixes for headlights though. Once that initial OEM UV coating is ‘dead’, you’ll need to do headlight restore every1-5years depending on the method you use. That’s why I offer lifetime guarantee on all my restorations. 🔥end result you have in the video though!

I do this professionally with wet sanding and UV compound, then add a hard UV clear. Last a long time

Permanent is a strong word. Regardless, this is the best restoration method. The only thing possibly better is new OEM lights.

Did same for my Honda Jazz. It holds already about 7 years. Main thing is - use 2k varnish.

I do the same thing but with a paint gun just lays down better. Nice job tho

Thank you G thanks to u I learned something new today

Give headlights a good once-over with a red Scotch-Brite pad. Then wet sand with 1000 grit paper. Use the cheapest rattle can clear you can find. Been doing it this way for 20 years headlights look like new.

This beat is 😊😊😊👍👍👍 whats the name of it? Did you make it?

Where I live- I get bugs stuck on the clear before it dries :D

I bought the Sylvania restorer kit and got incredible results on my old Subaru. Follow the instructions and walk away with a huge smile.

Hell yeah! That’s how it’s done! Showing my kids so they can do it this weekend! 🙌🏼👏🏼😳

For better results that last longer, use a polisher & coat it with a ceramic coating for longevity

Before doing it on the real thing, take a broken headlight glass from wherever you could find or a junkyard and then apply same step on a trial piece first then with your headlight

Thanks bro my headlights really needed this

Nice work sir👍👍

Brilliantly done

U got new subscriber 🤝

literally looks like they just came out of the boxs brand new looks amazing tho I need to do this

Legend has it AI kept on going past 1000grit...

Awesome! What temperatures are best for applying the clear coat? Also how long to wait to apply a ceramic coat after the clear coat has cured?

Now that’s how you do it 👍

Good work good work

My dad showed me this himself. Only he kept going up the grits then buffed and polished. Hasn't yellowed again without touching them in over a decade

looks great !t

cant believe luxury brand cant offer glass headlight literally never turn yellowish. i have a mitsubishi with glass headlight and it never turn yellow and is still crystal clear after 20 years

Well I have to say, that’s new to me and came out better than I thought it would. Good work!

That man did that 🎉

You aren't even going to tell me what the coating is that all I needed to know and you want a like a subscription

What's that spray called?, I tried it with polishing wax it worked but not to that perfect extent

Polish and put on some quality PPF (paint protection film) and last way longer and protect the headlight from gravel.

After I sand I normally use a rubbing compound the. Clear

Amazing work!💪

That’s not permanent but definitely the most effective.

I could never bring myself to use clear coat on headlights. I just polished mine until they were flawless. The big trick is just to take the headlight out and polish them while you watch tv or a movie. Well done though bro! Yours turned out great 👍

Please make sure there are no other vehicles anywhere near before you start spraying because you will cause overspray to attach to the paint and windshields it travels outside also.

What's the difference of scratching horizontally and vertically ?

very nice!

Bro you are a magician ! That's so so perfect ! Hats off to your skills and knowledge in the field. One question - what would be some practical precautions to avoid this yellowing kind of thing of headlight ?

Hehe i thought hes gonna use the usual "toothpaste"Trick😆

Don't forget to change the blinker fluid after the final spray

That looks like it came out really good. What did you use for a clear coat???

Jepp, that is the only right way to restore your headlight ! I have used 300, 800, 1500 grit and then 3 layers of 2k clearcoat 😁 great video 🤙😎

Can you wet sand the clear coat after it’s cured to get a better finish?

You need an UV protective coat after the heavy coat.

Not just 'clear coat', you should use an UV resistant clear paint.

Permanent is a big word

This is some which craft right here man 😯 looks brand new!!

Your process is awesome just everybody has their own preference in my experience with modern hand older cars buffing and wet sanding has always been good if I could change anything I wish they went back to glass steel beams we wouldn't have to be buffing every clearing anything

Just remove the whole light, then remove the upper cover and clean it, then install it back simple.

Any reliable clear coat brand recommendation? I need professional grade

Perfect job brother...😉👍🏻👍🏻👍🏻🇲🇾

Incredible results well done, when do you feel it’s right to stop sanding and move on to the next step ?

much better than using a heat gun because the heat gun will dry out the plastic and youll get the same issue even faster.

Car manufacturers should consider using replaceable lenses, to be green & to be nice.

Unbelievable

Which spray ???? Normal cleaning spay

In Germany we say: jegliche Änderung an der lichttechnischen Einrichtung an einem Kraftfahrzeug führt zum Erlöschen der Betriebserlaubnis. Scheinwerfer sind Bauartgenehmigte Teile. 😅

Great job!

Spray a thin then heavy coat of what¿?

How long does it take for headlights to fade like that? Had a 9 year old vehicle and the headlights were still as crystal clear as the new car that replaced it..I just assumed that was a "Thing of the past" with like vintage antique cars or something...no?

Gotta watch this vid when it's time to do my headlights

"Pop the hood? Yeah pop the hood!"

Thats really unbelievable..!!! Can it really be done like how you've done...??!

Which spray this guy used?

What’s the spray can make and brand?

Ez Pz😂

My dad did these for my wrx and im truly grateful

While tacking, are you doing a wiping motion or patting motion?

Thank you and good job - sure it’s tedious, but great results!

Make sure you warm the can Best way is to warm it in the microwave

Instead doing all these, we can change the doom

Jokes on you, my Datsun has glass headlights btw, great service you done there. I'll clean my dad's cars like this

can and should you do this for taillights?

Do you need any better results polishing the plastic itself to clear finish or is the 2K clear enough which obviously I see it clear but just wondering if polishing the plastic perfectly is a necessary step that I take

Bro fixed my major problem. I was about to buy new headlights. Thanks 😎💯

Overspray is gonna ruin your paint and any other car around it though

Is it a new headlamp lmaoo

Still easier than reaching to another planet to do the same.

Can confirm this is the best way!

But spray with what??

My BMW needs this service done!

Which product do you use for the coat?