Tiger Tool 10102 Heavy Duty Universal Joint Puller - Best Way To Disassemble Drivelines!

Рет қаралды 181,451

11 жыл бұрын

tigertool.com/products/commer...
The World's greatest and "original" U-Joint Puller! Engineered for use with up to a one-inch impact wrench, this tool provides the ultimate "brute strength" for disassembling drivelines.
Fits Spicer drivelines 1610, 1710, 1760, 1810, 1880, Meritor (Rockwell) 16N, 17N, 18N, 1710, Spicer SPL 140, 170, 250 "Life Series", and Meritor RPL 20, 25 "Permalube" Series. (Designed to work with U-Joint bearing cups from 1.5" to 2.2" and will fit virtually all Class 7 and 8 Trucks and Machinery)
• Eliminates dangerous jacking, hammering, and torching.
• Removes sealed u-joint cups in minutes.
• Does not damage the driveshaft, yokes, joints, or bearing cups.
• Tested and recommended by Dana Spicer Corp.
• One piece unit! No bolts, no cables, and no adapters.
Made in Canada - Tested and recommended by the Driveshaft Division of Dana Corp
#tigertool #Trucktools #truckmechanic #Trucktechnician #heavyequipment #heavydutymechanic #dieselmechanic #cooltools #handtools #Dana #Spicer

Пікірлер: 36

@TigerTool Жыл бұрын

Visit our website for more information: tigertool.com/products/commercial-u-joint-puller

@terrellscaife2411 3 жыл бұрын

This could be the greatest KZfaq video ever made

@taylorculley2461 7 жыл бұрын

ive only had to use this tool once but when you need it,its worth every penny

@lazarollanes5228 2 жыл бұрын

Thank you so much, this is video really helped me

@dormindont1 10 жыл бұрын

Отличная приспособа!

@SignatureStampsFan 8 жыл бұрын

I love this tool.

@jessetoptechallen1461 7 жыл бұрын

good tool

@cliffordshaw3032 4 жыл бұрын

I love this tool , how much it cost

@geoffclark9820 7 жыл бұрын

On full mechanical u-joints it's a must! In Canada the salt in the winter will seize it solid. He keeps the impact going like a moron, I run it up tight and smack the ear. That way you don't wreck the yoke or ear on the drive shaft. I have to say though, the tiger tool kingpin press tool is a bag of shit. I paid $1600 for mine at Gregg Distributors. Works fine if the kingpin is sicky but if it's seized into the axle it doesn't work at all which makes it absolutely useless. For $1600, it should work on everything!

@shortthrow50 6 жыл бұрын

Geoff Clark nobody else that I know has such problems with their u joint and kingpin removal. In the United States we own grease guns

@mschelleman925 6 жыл бұрын

Hey cockwad we have grease guns up here too. We also have licensed mechanics. something you guys should look into

@ScottDLR 3 жыл бұрын

I dont know about the tool itself but your video is sure better than "OEM's" poor attempt.

@TaintedMojo 3 жыл бұрын

Is it actually designed to be used with an impact gun?

@TigerTool 3 жыл бұрын

Yes

@ryansmithberger3140 10 жыл бұрын

is there a smaller version for the auto industry

@thebad300 7 жыл бұрын

yes but does not look the same look up ball joint/ujoint press www.amazon.com/OTC-7249-U-Joint-Anchor-Service/dp/B0002SRGXY

@mirocabraja5128 7 жыл бұрын

Wddddddfdd

@conrad3932 Жыл бұрын

💕

@mandoky1647 Ай бұрын

Until the threads strip out on the tool.

@TrentBigW 9 ай бұрын

I drive a wrecker. We have to pull and hang the driveshafts, and we dont actually pull the u joint. We just seperate it from the yoke. Do do i just need to pull the two? Or do i still need to pull all four caps?

@TigerTool 9 ай бұрын

You can just remove the 2 caps on the one side.

@TrentBigW 9 ай бұрын

Thanks so much

@andrewwilson8317 7 жыл бұрын

No grease points on that UJ?

@kurtdogg32 6 жыл бұрын

Andrew Wilson I seen one, not two. It's got some caked grease on the bearings too.

@surendarasinghsardar9764 2 жыл бұрын

I have to take this how much is it

@TigerTool 2 жыл бұрын

tigertool.com/products/ujoint-puller?variant=33571416965258

@Mr1968gtx 10 жыл бұрын

Tiger Tool part # 10105 or 10104

@shawclifford5332 4 жыл бұрын

Where can i get that tool to buy

@BACONNWRAPPED 4 жыл бұрын

amazon

@TheTERIO14 9 жыл бұрын

You shouldn't be using an impact on a puller, it's very dangerous. If the joint is stuck, you accumulate energy in it qnd when it unstucks, the puller or joint could break and cause serious injury

@thebad300 8 жыл бұрын

+Gabriel Thériault as long as you are not a dumbass and use the correct lube on the screw its not an issue

@docofswank88 6 жыл бұрын

When it unstucks....when it breaks free. Real fine work ya pus

@familytraditiontransportat7951 Жыл бұрын

Pretty sure the maker of the tool knows how best to use it... But hey if you want to use a ratchet by all means go ahead Popeye.

@TheTERIO14 Жыл бұрын

@@familytraditiontransportat7951 damn i was dumb 7 years ago

@envisionCamusa Жыл бұрын

@@TheTERIO14 I respect people that learn and admit to things.