Tire Insert Tech TUNE THE OFFSET

Рет қаралды 4,846

9 ай бұрын

Hopefully this will help use what can be considered an issue and make it into a tunable feature.
e6000 Glue Amazon amzn.to/3Zxrn83
YZZR yzzrinserts.com/ www.etsy.com/shop/YzzrInserts
3BRC Antifoams www.3brothersrc.com/
SL3D Squid N Certs sl3drc.com/
Flub RC Stufferz flubrc.com/
BAMF Inserts www.bamftireinserts.com/
Exocaged RC exocagedrc.com/
Flysky GT5
Amazon amzn.to/3z5VAOV
Radiolink RC8x
Amazon amzn.to/3OvEbqe
Amain Hobbies bit.ly/2RsdBVl
Horizon Hobby
Tower Hobbies bit.ly/3o7twsR
Escape CamperVan bit.ly/3Jck8dl
BeardBrand (BeardStuff) bit.ly/3xD6af8
If you would like support Exocaged RC Directly, consider being a channel member. Cheap monthly membership fees, they are $1.99, $4.99, $9.99 and for the big guys $24.99. Take a look! / @exocagedrc
Get Upside to save on your gas! I let it build up till christmas and cash out a few hundred $$$ each time. Click this link to get a $5 bonus the first time you make a purchase. upside.app.link/9H6W8
#insert #crawler #rctruck

Пікірлер: 36

@FRANKO-iu3dx 9 ай бұрын

I like your security guard there nappin'

@josephcruz671 9 ай бұрын

Exo, nice tips and tricks. By the way, thanks for joining the live from Guam last night. It's nice to have people like you.

@needlejuse1113 9 ай бұрын

✌😊😜😀😁👍

@CRAZYBUILD349 9 ай бұрын

NICE, great looking inserts, sweet looking tires!! thanks

@needlejuse1113 9 ай бұрын

😁😀😜😊👍✌

@CM-ig2pf 9 ай бұрын

Awesome FYI thanks!👍👍😀😎✌️

@old-rcplane-phart 9 ай бұрын

👍😁

@MRT_H 9 ай бұрын

I suppose if you printed your own inserts, you could add a shallow groove in the inside of the insert so you can align the inner ring where it spins true, once you figure out the offset you want. Or add a small shoulder inside the insert to stop the inner ring from sliding. But I am purely just suggesting here. Great video, as usual!

@RuisRcAdventures 9 ай бұрын

I use 1.9 and 2.2 squid inserts but i dont have any side shift. Good to know this little hack though. Nice Joe 👍

@mr4x4s 9 ай бұрын

SL3D RC makes Squid’nserts for Negative G Inverse wheels, Proline wheels, Spec RC wheels that lock into the lock rings of those for zero side to side shifting!

@Clayton_B 9 ай бұрын

Thanks!

@ExocagedRC 7 ай бұрын

Thank you so much!

@madmaxx010 8 ай бұрын

I've been using two sided tape around the OD of the ring... Works pretty good

@tristianmason4730 9 ай бұрын

I absolutely love those cheap rims I got them on my trx4 blazer and my k10 high trail im going to get those inserts for my blazer 🤘🏻🤘🏻

@jerryvolpini7987 9 ай бұрын

Apply a little glue around the inside edge of the ring (the side being inserted into the tire), and as you install it, the glue is spred over the entire ring - no mess! Assemble the wheel/tire and lay the inside of the wheel on a flat surface. Push against the ring and ensure it is sitting flush. Let dry over night and Bob's your Uncle 😊

@old-rcplane-phart 9 ай бұрын

ExocagedRC master class!😂

@needlejuse1113 9 ай бұрын

🎉🎉🎉❤

@covecityboys 9 ай бұрын

The one exception to this is some carbon fiber Chinazon wheels I use that I found on Amazon that have inner clamp rings that perfectly fit the Proline dual stage inner rings. I’ll link it later if you’re interested. They go great on Capra wheels too.

@JPWirt 9 ай бұрын

I just use double sided Scotch tape on the OD of the ring, the real thin stuff in the yellow dispenser.

@madmaxx010 8 ай бұрын

Same here

@MitchellBolognaniRC 9 ай бұрын

Great information 👍

@needlejuse1113 9 ай бұрын

Awesome❤

@Hardlines_FullsendRc 9 ай бұрын

Squid inserts for the comp cut Specrc wheels allow for zero shifting. But it’s a very expensive setup,especially the wheels😁

@misguided5421 9 ай бұрын

You can also glue the ring, build the beadlock wheel and set a few 5# dumbells on the outside bradlock and push down on a flat table. Leave the dumbell for 24hrs and done.

@jerryvolpini7987 9 ай бұрын

Just rest the wheel on it's inside edge and ensure the ring is sitting flush, then let dry. I wouldn't use weight, it can deform the insert and cause inconsistent results.

@misguided5421 9 ай бұрын

@jerryvolpini7987 thanks for the advice but I haven't had an issue doing this yet. Using SL3D squid inserts....but I can see that possibly happening.

@rc-daily 9 ай бұрын

What I do is put a ring of double sided tape on the inner bead lock ring

@rc-daily 9 ай бұрын

And 3brc antifoams have the least amount of shift that I've found so far

@Gmcworrior1 9 ай бұрын

Hi kitty!!

@toolbaggers 9 ай бұрын

The hole in the side wall (a fatal flaw in full-scale) means sand/dirt/water goes in, but won't come out. A maintenance nightmare as having unbalanced wheels/tires means poor performance and increased wear and tear. At least a hole in the tread means that centrifugal forces will not only actively keep sand/dirt/water out, but it will also tend to eject sand/dirt/water if it does enter the tire.

@jerryvolpini7987 9 ай бұрын

The 3d printed inserts don't flex and breathe like normal inserts and a hole in the sidewall tends to work better. Besides, a hole in the tread NEVER evacuates all the water and very little dirt/dust. Not to mention, Joe is using beadlocks that can be disassembled and the water and dirt removed 👍

@ello4792 9 ай бұрын

question for you!!! is that one hole you have drilled on the sidewall all thats needed to vent a set of tires?

@guywithashovelproductions 9 ай бұрын

That side shift drives me nuts....dual stage foams are the worst. I'll usually put a few dabs of super glue to keep them together 🤷

@austinelmgreen9338 9 ай бұрын

Is this stuff easy to get off when you want to switch wheels or something?

@cheagle464 9 ай бұрын

Question, anyone. Painting a body, painters tape trimmed away at points. Forgot to run a fingernail over trimmed edges. DOH!! Ya, leakage. Can i use thinner on a swab to clean the leakage? Or will it damage the plastic? Not huge leaks, just like not crisp

@toolbaggers 9 ай бұрын

Those rims are way too skinny for the tire width. It's not even close to what would be acceptable in full-scale.