Bought the same carb off Ebay .Now my 2002 500 Sportsman is running great.Replaced fuel lines ,fuel pump,carb ,and intake boot.Its was backfiring , rough idle ,and random stalling.All aftermarket parts .Thanks for the video.I highly recommend this carb ....$40 ..no brainer !!!
@boebradley867 Жыл бұрын
What carb? There alot of then in Amazon. Can you give the order number? I guess I'm spoiled but a sure called Rusted Nut Repair actually shows the biz the parts come in asking with part order number etc. That is awesome. I wish everyone aphid do that. That's the most important part is knowing the part to order exact thing. Heck your site could even win a sponsorship for it, it happens. Thx!
@carlhaggard3792 Жыл бұрын
I am having the same problem with a 98 Kawasaki bayou 400. I want to order carburetor off eBay just don’t know which one. Thanks.
@ebenjamintoane7 ай бұрын
What brand is that carburetor?
@ebenjamintoane7 ай бұрын
What brand is that carburetor?
@adamfrancis54072 жыл бұрын
I've owned my small engine shop for 15 years. Chinese carbs are a great solution once you learn the common quirks. I've used these on polaris a handful of times too with good results.. They also like the vacuum needle valve raised more often than not for best wide open performance. With or without ethanol blended fuels. I'll be replacing the carb on my 600 twin soon. I'll try the one in your link and see how it runs. Nice video!
@TitaniummanGarage2 жыл бұрын
I just replaced one on a 600 twin. It worked great. Just make sure the intake boot isn't ripped like mine was.
@jdiddy6901 Жыл бұрын
@@TitaniummanGarage I just put one on my 600 because the factory one started leaking like crazy from the overflow even though it runs good. New needle and seat didn't fix it. New Chinese carb is overflowing too, though not as much, and not running right (almost like it's missing at high rpm and won't idle). Any ideas?
@user-sn2jt7ph6c11 ай бұрын
can any one recommend a good after market carb for my 2203 polaris ranger 500
@smallgaragehustle2 жыл бұрын
Great video! I’ve used these with great success over the past couple years. One time I had one out of the box the top end parts were floating around the diaphragm but it took a couple mins to reassemble and it was fine. Magnum 425 came to me with a suspected faulty cam lobe, which turned out to be a bad carb. Swapped in the new aftermarket carb and flipped it for a very nice profit.
@TitaniummanGarage2 жыл бұрын
Sweet!
@shahriarfathi45692 жыл бұрын
@@TitaniummanGarage few time i ask you question but never get respond from you
@TitaniummanGarage2 жыл бұрын
@@shahriarfathi4569 I've scrolled through my messages. I Dont see one from you. I get so many messages a day. Sometimes it's hard to keep up.
@shahriarfathi45692 жыл бұрын
@@TitaniummanGarage shahriar fathi 1 day ago thank you so much for information . only thing i like to know i have Honda and need 36 mm Carb so what you recommend
@chrisschmitz1926 Жыл бұрын
@@shahriarfathi4569 sell it and buy a Polaris lol
@ctroy64 Жыл бұрын
Thanks for this video, I was looking at spending $180 for a new carb but your link saved me. Just ordered one for $38!
@markallen938624 күн бұрын
2004 330 trail boss. New China carb (on it when I bought it...not running...rings frozen in piston...new rings) After installing new rings it fired right up, idles good, everything is good until you get to half throtle and then it boggs down. Haven't decided if I should try to fix this carb, rebuild an oem or buy another $40 China
@daxmorlock78462 жыл бұрын
I've put some of the cheap carbs on different bikes and always bought a jd jet kit to go with it. The Chinese carbs always seem to run lean. Working on a 06 scrambler 500 now that has a Chinese carb and like always it's lean.
@jackbowden33952 жыл бұрын
I bought one it works great, I haven’t had a problem with so far .
@boebradley867 Жыл бұрын
Where did you get it? What brand and company?
@jackbowden3395 Жыл бұрын
On Amazon
@boebradley867 Жыл бұрын
What's the name .. there's hundreds in Amazon..
@boebradley867 Жыл бұрын
I wish someone had the Box so we'd know what product is so good from them. I need to buy one myself so please help if possible..😀
@jackbowden3395 Жыл бұрын
@@boebradley867 I’ll try to locate the box I have it in my shed
@daviddecaro4558 ай бұрын
I just put a Quad-Logic carb on my 2001 Sportsman 500ho last night. At first i thought it was junk, but then we found the cracked carb-to-intake boot. Ordered the boot, and I'll let you know how it is when we're done. Btw, thanks for the great videos. They've been extremely helpful on my project. Just did a transmission install this week thanks to your channel. We'd like to see a video on the removal of the transmission gear sensors please.
@TitaniummanGarage7 ай бұрын
Quad logic I've had good luck with. That sensor only has 4 screws on top and comes out after unplugged.
@daviddecaro4557 ай бұрын
@TitaniummanGarage ok great! I'm having trouble with the one sensor. It shows still in neutral when in high unless you wiggle the wires on the sensor. Thank you again for replying and the excellent videos.
@timkevwitch862 Жыл бұрын
Just replaced one out of 325 trailboss from ebay Michigan company $38 works great much easier than trying to rebuild. I've always had trouble with the float on rebuilt like you said to many ports that contain garbage.
@warrenvalentino5763 Жыл бұрын
Great video. i put an aftermarket carb on my 1995 polaris 425 magnum 2x4 and it is working Great. i am only the 2nd owner of my wheeler. :)
@johnshepard11572 жыл бұрын
The fuel pump on my 2000 Polaris 500 6x6 puts out 3-5psi. I wonder if this carburetor can handle that psi or if it will just force the needle down and overfill it?
@OutLaw-xs8nbАй бұрын
Where does the bottom carb fule line goes???
@cm58382 жыл бұрын
I have a small engine/atv shop and some times the old carburetor is a goner. I have had mixed results with the Chinese carbs, every single one I bought last year aside from one the jetting was way off and I couldn’t find alternative jets to fit them. This year I have bought one and it will not win awards but it works. However I am about to order two for a Polaris magnum 500 and a sportsman 500 due to the carbs I got with them are absolutely destroyed. I’m switching though to a “brand” that is trying to build a reputation, that seems to sell pretty good piston and cylinder kits, niche. They claim to sell jetting kits for them
@TitaniummanGarage2 жыл бұрын
Just dont use their head gaskets. They are junk. I have a love hate relationship with that company.
@daddybusy7496 Жыл бұрын
Let me know the outcome...
@cm5838 Жыл бұрын
@@daddybusy7496 outcome is they worked, they actually worked pretty good. They even held an idle far better than other Chinese carburetors I’ve used.
@danielfoster65882 жыл бұрын
Zoom zoom makes a decent carb for cheap money
@JamesParus2 жыл бұрын
I had that overflow fuel . Its the needle valve base o ring. Changed that and leak stopped. I also ultracleaned the whole thing but I think there is still some blockage somewhere as it has little hesitation at wot. Idle and all the other stuff works ok.
@boebradley867 Жыл бұрын
You talking about the needle valve for the float? Or under the float? In not a carb pro, but that info would help. Thx!
@JamesParus Жыл бұрын
@@boebradley867 yes, the needle valve for the float. it has brass base that has o ring under it to seal it. it's common to leak. the needle could be fine but if that base leaks against the carb frame it's not going to hold.
@GearHardoffRoad2 жыл бұрын
The jet on the bottom was froze in mine when i rebuilt it and i couldnt get it out! Runs better now but never got to change that
@stuby20148 ай бұрын
There is good and bad aftermarket products in every field, but if you count on warranties these days it's potluck.Either companies make you jump through hoops or they close down and open up the next day under a different name.
@RogerBurford-cu8hf2 ай бұрын
I have searched for hours on ebay for any Chinese carb with a 10 year warranty, can you give us a hint? Thanks, great video.
@dannyc41934 ай бұрын
Got a after market carb with no luck and I can't find a carb for 03 polaris trailblazer 400
@MirandaDetailing Жыл бұрын
I have fuel leaking out of my 2005 scrambler 500 HO and i think the float is bad or something. so i got a carb like this ebay and hope to replace it. I saw a few of your vids on removing the carb but do you hvae a vid or two on removing everything to get to the carb? Thanks
@richardsoule2782 ай бұрын
great job, hey the polaris 500 ho carb fuel inlet opposite side or the right side? opposite of the others which is the left feed.
@jeffmaeder12302 жыл бұрын
Can you link the carb with the 10 year warranty in the description?
Will this carb u just linked work for the sportsman 600s?
@hashdfw3 ай бұрын
Bought a chinese carb and it worked for a year before it kept flooding out the engine. If you shut the engine off it was really hard to get started again. Bought another one and it did it immediately and even started dripping gas. My fuel pressure is 3 psi. Needle and seat are junk on these.
@poochie4912 күн бұрын
Sometimes the needle valve gets dislodged during shipping and handling so it leaks right from the get go. So always check that before installing a non OEM (Chinese) carb.
@Jp-iy6ix Жыл бұрын
They wont take any carb back if its had fuel in Iit and yes the float sticks in them
@boebradley867 Жыл бұрын
What carb? What's the part number? Or any other info needed to buy the same one?
@BANGDANGOW452 жыл бұрын
I'm about to grab one off eBay rather than take mine apart. Hope I fix it. Ect. For 40$ why not. 04 predator falling on it's face when given full throttle. Tried the cdi box. To no change. Next step far as I'm aware is carb
@justincoffey7429 Жыл бұрын
I'm on my 4th Amazon carb for my 04 Sportsman 600 Twin. I'm at an absolute loss. No matter what I do, I just cant get it to run properly. I've adjusted the needle seat depth, mixture screw, idle, everything. It runs super rough at idle like its on one cylinder even though I've tried adjusting the mixture screw while warm and nothing, then giving it gas up until 3/4 throttle it bogs and chokes down like its crazy lean, and then runs like a top and scalded dog at 100% throttle (157 main jet) About to say screw it and order a QuadLogic carb, or just eat it and take my stock Mikuni to Polaris and have them fully go through it because obviously what I'm doing isn't working after reading tons and tons of literature online.
@TitaniummanGarage Жыл бұрын
I'm having the same issue on a 700. It all depends on who makes the carbs. I buy alot on ebay. Some are junk and some are spot on. I've tried a couple different companies. I've heard moose racing makes a good carb for 160.00. I haven't tried it yet. Have you considered buying a sonic cleaner for your original carb? Once fuel residue is in the carb its really hard to get out unless you soak it. You said it sounds like its running on one cylinder. Have you checked to see if your getting spark at both plugs? If you still have the old ducatti ignition system in it (they are horrible, Polaris stopped using it) you might have a bad coil, cdi, or stator.
@anthonyrich8552 жыл бұрын
I clicked on the link and it took me to a page on ebay for a different style that the throttle is on the right side not left side
@kawasakikfx700guy82 жыл бұрын
I got one for my polaris 600 , just got a rebuild kit to match my jets works Awsome, don't leek anywhere
@watermelon8565 Жыл бұрын
How did you know it matched the carb you bought?
@davekeeping28148 ай бұрын
ut in the spring and cable into it. can you show how to put in the choke cable. I got new one like you but the hole where the choke cable goes in has a brass fitting in there so it wont seat in there
@AmericanDefender Жыл бұрын
What about ditching the cv carb and going with a regular slide carb?
i purchased an after market carburetor,, it was doomed after they packaged it for shipping ,FED EX did a terrible job of shipping,,the box was crushed so bad , the inside of the box had dent impressions of the carburetor, popping the bubble rap , and when it arrived the driver threw it out of the on the ground in front of my house , it never worked at all ..
@TitaniummanGarage8 ай бұрын
I would tale the parts out and rebuild your OEM carb.
@kenwimmer39368 ай бұрын
@@TitaniummanGarage thanx for the reply!! I did a good Micro Cleaning on the OEM ( Pput a new pulse pump on it ,, the new carb wouldn't even work with new pulse pump)it runs and starts better than NEW , I did this in September, I cut a fair amount of firewood, and drag alot of trees out of the woods to be cut up.. (03 600 sportsman,, 2300 miles on it ) I found your channel after the carb problem,, I'm a subscriber Now .. your Videos are great , to the point, no extra B.S. ,,, keep the Videos coming 👍👍
@kenwimmer39368 ай бұрын
@@TitaniummanGarage and here is another funny story,, when I bought the new pulse pump at MIES OUTLAND in MN. it was an after market pulse pump,, it leaked gas , new out of the box ,, for a few dollars more I bought the OEM , and it worked Great ..
@guillorios9327 Жыл бұрын
Greetings, how many turns does the jet pilot screw have? I moved it without realizing it in the turns that she had and now she doesn't even want to start. It's a polaris scrambler 500
@BassFace17764 ай бұрын
The link for ebay doesn't work. Can you post the new link to the brand/ebay store? Im afraid to buy Chinese carbs but if there was a brand that was reputable I'd be interested.
@TitaniummanGarage4 ай бұрын
They went out of business. I buy china carbs and if they dont work I use the parts to rebuild the oem carb.
@jessecoffey3069 Жыл бұрын
Mine won't idle and spitting gas out of overflow
@johnmccoy22162 жыл бұрын
Would the carb in link work on a sportsman 500? Throttle lever is opposite side than stock carb positioning. I bought an aftermarket one that all it will do is idle that’s it won’t rev up just dies. Adjusted float, needle and new pump still won’t do anything but idle.
@juiced712 жыл бұрын
I never messed with the quad carb What size are they 36 / 38 ? If so I would try a 44 it will make more power! At least with the minibikes it made some pretty good power …. Also I heard soaking the carb body in pine sole comes out pretty nice never done it myself ….
@robbran81882 жыл бұрын
Ok, I just ordered a carb for my 2003 sportsman 500 ho from James-club. It should be here Tuesday July 12th. Is there anything I need to know, I'm hoping I just put this thing in and maybe have to adjust air fuel. Are my hopes too high. If so you got to make a video between know and then of totally tuning and setting up a carb from scratch. Thanks in advance!
@chandlerhuerta62863 ай бұрын
What intake boot do u need to make the aftermarket carb to work
@TitaniummanGarage3 ай бұрын
Depends if is an H.o. or non H.O. carb.
@allenramsey1825 Жыл бұрын
I bought the cheap carb off ebay for my Polaris Sportsman 500. Worked great for 1 year and now it leaks fuel from the overflow tube as you mentioned. Now wondering which way to go as you are.
@TitaniummanGarage Жыл бұрын
Order a needle and seat from All Balls racing. It has a rubber tip on the needle. I think why they leak is they use a metal needle without the rubber tip and after it wears it leaks.
@sombradesigns1734 Жыл бұрын
How's it holding up a year later?
@philrs6662 жыл бұрын
Awesome find. The listing mentions that it fits scramblers, would it work for a sportsman also?
@TitaniummanGarage2 жыл бұрын
Just make sure if its a H.O. carb or non H.O.
@biz4twobiz4633 ай бұрын
nice video. yes, 10yr warranty, but that is if the company is still around in those 10yrs.
@renemacao93494 ай бұрын
The link you put up doesnt work. I need one
@TitaniummanGarage4 ай бұрын
Went out of business
@renemacao93494 ай бұрын
@@TitaniummanGarage aww man :( you know any other one?
@deanmeier54287 ай бұрын
Good show titanium. What kind of China carb is it? What kind do you recommend for a scrambler 400
@TitaniummanGarage7 ай бұрын
I just bought a carb with a 60 day warranty with 1PZ on ebay. They seem to have good parts.
@garypitzer8729 Жыл бұрын
Dorn it I clicked on your link, and they are out of stock.
@geronimomadmartin349911 ай бұрын
Have you ever tried the aftermarket chinese diaphragms for the Mikuni CV carbs? I was wondering about them because the oem one for the Polaris Ranger 500 is about $150.
@TitaniummanGarage11 ай бұрын
I've actually stripped a china carb and used the parts in a oem carb. They work good.
@geronimomadmartin349911 ай бұрын
@@TitaniummanGarage I am in the process of getting the new chinese carb dialed in but whenever I take it on a downhill slope it runs rich and sputters, when it's uphill it runs fine. What would cause that? And other than downhill it runs better that it ever has before. It's making my brain hurt lol.
@happy_dad42112 жыл бұрын
I’ve got a 1996 Sportsman 500 non-HO. Would this carb work on it as well? Love your videos.
@TitaniummanGarage2 жыл бұрын
Yes. When you order it. Just make sure it's for a non H.O. the H.O. carb is bigger
@HomesteadOnThePreserve Жыл бұрын
Carb in my 2005 Polaris 330 is leaking fuel real bad. Instead of the typical FleaBay carb for $40 I just spent $160 for one sold by "MOOSE Utility Division." It's also made in China but i'm hoping its quality due to the price and name backing. Hopefully I didn't get ripped off. We will see, i'm doing the install today.
@anncampbell4300 Жыл бұрын
Are you happy with your $160 vs $40 decision?
@HomesteadOnThePreserve Жыл бұрын
@@anncampbell4300 Yes, 100% satisfied! Sorry, I forgot to do a follow up. I kept the jets that were already installed and just needed to tune it. On the 3rd try I had it running perfect, from smooth idle to wide open throttle. I won't know if a cheap carb would be the same but I wouldn't take that chance.
@cardadbods20077 ай бұрын
Hey could you update the link to where you Is bought this carb with 10 year warranty...?
@TitaniummanGarage7 ай бұрын
Its an old video. Its no longer available.
@soonerjoose Жыл бұрын
Hi, I bought this carb off of eBay for my 2002 Polaris Ranger 500 4x4. I installed it, and it started right up and it was running great. I drove it around out in the pasture, then took it back in the barn and there was this overwelming smell of fuel. I looked beneath and it was leaking fuel. The fuel is coming out of the drain tube on the bottom of the bowl. It does this everytime when I drive it more than 5-10 minutes. I'm not a professional mechanic by anymeans, I'm more of a Google/KZfaq mechanic. Do I need to adjust the screw on the drain tube or is this something way above my head? Any help would be greatly appreciated. Thanks!
@TitaniummanGarage Жыл бұрын
Unfortunately, some of the aftermarket carbs leak. I stopped using them for a while because of that. It's your needle and seat leaking. Try to get your money back or buy a needle and seat from All balls racing and replace it. I believe I have a video on that.
@user-sn2jt7ph6c11 ай бұрын
Could you please tell me what brand after-market carb you recommend for my 2003 polaris ranger 500?
@TitaniummanGarage11 ай бұрын
I cant recommend one. It's been hit and miss with the aftermarket. Most times if it get a leaking china carb I use the parts and rebuild the oem carb.
@marcinhak2554 Жыл бұрын
Hi I have 2003 polaris sportsman 500ho 4x4 I need a carb for it I can't find from that seller you mentioned in your video. Perhaps you have link to it somewhere. Thanks in advance
@TitaniummanGarage Жыл бұрын
I think he stopped doing it. I can't find it either. Moose racing came out with a carb I've heard is good.
@ebenjamintoane7 ай бұрын
I liked your video: down to earth unpretentious advice. But I could not find an after market carburetor with a 10 year warrantee on the ebay link you provided. Can you give me the brand name and order number with what you've had success with?
@TitaniummanGarage7 ай бұрын
They discontinued that.
@ebenjamintoane7 ай бұрын
Thanks. It was too good to be true, anyway. Can you recommend a few companies who make a decent carburetor?
@TitaniummanGarage7 ай бұрын
@@ebenjamintoane Its touch and go with these companies. I recently bought a carb from 1PZ. It has a 2 year warranty. So far so good.
@deanmeier54287 ай бұрын
Thanks titanium your aw
@shahriarfathi45692 жыл бұрын
thank you so much for information . only thing i like to know i have Honda and need 36 mm Carb so what you recommend ?
@TitaniummanGarage2 жыл бұрын
Oh..I see. You asked about a Honda. I dont work on them so I cant be certain. They do make aftermarket for hondas. Maybe check ebay.
@shahriarfathi45692 жыл бұрын
@@TitaniummanGarage OK i see you work on ODES i have 1 Honda and 2 Odes 400 for my kids so is same thing only interesting was you said 10 years warranty and that is why i like to buy 2 or 3 of them for spare Honda and odes is 36 mm all 3 atv i have is japan Carb on it
@TitaniummanGarage2 жыл бұрын
It's been 5 years since I had those odes and Honda. Once I found out how difficult they are to work on I switched to polaris. Polaris has the Transmission and engine separate. So it makes it easier to work on.
@shahriarfathi45692 жыл бұрын
@@TitaniummanGarage yes is only problem with Honda but i was lucky with electric shift i had problem on one of my kids Odes and after i spend big money i do with foot manually is ok but when i find my kids stok
@jim49az Жыл бұрын
where did you buy it? mfg?
@steveyawn619210 ай бұрын
I can’t find it on eBay, can you give me a part number or eBay seller name? Thanks!