Today, I show you how to use

Рет қаралды 153,737

Жыл бұрын

Пікірлер: 145

@foreignjos 10 ай бұрын

Wouldn’t it be better to drain the old oil first then put castro oil with the engine flush, drain that and fill up with the liqui moly 5w40 , seems like that would be a better clean.

@MaybeImJustAsian 10 ай бұрын

The engine flush is designed to be used exactly as I showed you in the video so that’s how I’m going to use it since the engineers that designed it knows more than I do

@NFLYoungBoy223 10 ай бұрын

Wtf that seems so expensive to drain some oil thats new😭

@Theyralltakenfu 8 ай бұрын

@@NFLYoungBoy223just use the cheapest oil you can find.

@Theyralltakenfu 8 ай бұрын

I get why you wrote that, it’s a thought I’ve had many times.

@GokuInstinct1 6 ай бұрын

@@Theyralltakenfucheapest oil is Walmart brand which costs $40 with the Walmart filter. 0W-20 full synthetic 6.8 quarts is all my car takes.

@LionsTigersBears Ай бұрын

Best cheap flush two quarts of dexron run it for 1500 miles drain and fill with your favorite oil.

@Need4Sweede 5 ай бұрын

Depending on how dirty your engine is, you should do a second flush with clean oil after draining the additive the first time. Add engine flush, drain and fill (with new filter), let car run for 10 minutes, then drain and fill again with fresh oil

@MaybeImJustAsian 5 ай бұрын

It all depends

@badsbiker 3 ай бұрын

Actually that 20w50 is too thin you should use a w60 oil in that engine

@David-yi1fp Ай бұрын

A quart of K 1 Kerosene arguably works the best for cleaning your engine internals!

@MaybeImJustAsian Ай бұрын

I mean, by all means

@Amokof 5 ай бұрын

As long as you do your oil changes on time and use synthetic oil, you wouldn’t need to use any of these additives. Modern synthetic oil has detergents to clean out the old oil. Using engine flushes like the one in the video is fine if you’ve neglected your car for a while or if you’re buying a car with an unknown service history. Just make sure to not use it on a high milage car with unknown service history. Because if they haven’t changed the oil in a long time, there is probably going to be a lot of gunk and sludge build up inside. And if you do loosen the sludge with a chemical engine flush, they’ll probably clog up something in the engine like an oil pump screen for example. The safest way to flush an engine is to dump your old oil and filter and replace them with a new cheap synthetic oil and filter. Drive for 500 miles and then dump the oil and filter. Repeat the process 2 more times. On your third and last time, use a high quality synthetic oil and filter. Yes this method might be slightly expensive than using a Liqui moly engine flush, but it depends on how much you value your car. If you care for your car and want it in the best condition, use the safe method. If you dont want to spend much on it and are willing to take the risk, use the liqui moly engine flush.

@Quis85 5 ай бұрын

You would be correct but the wrong brand this applies to. L.M. is designed to do what the others don't do. Which is liquefy the slug so you won't clog up anything. I had that same question. The other flushes don't liquefy the stuck-on or slugged-up oil. So yes you will clog something. Those other brands lose it but don't dissolve it. But L.M. turns it into liquid so you can drain it. Some people depending on how bad it is. They flush it three or more times with the cheapest oil before putting in the good stuff.

@MaybeImJustAsian 5 ай бұрын

There’s pros and cons to doing it the long way like you stated. This additive is designed to do do what it does and does it very effectively for $15 instead of spending money on multiple oil changes

@Quis85 5 ай бұрын

@MaybeImJustAsian I don't know if this is from what I said or not but if it is let me correct myself. When I said multiple changing oil with cheap stuff. Some people do that to drain out the access L.M cleaner. Maybe you thought I meant using L.M. multiple times. If that is the case then I APOLOGIZE that was not what I meant lol. Nevertheless, the creator put up a KZfaq video and he says there's no need for a follow-up flush using new oil. One flush drain and put fresh oil in and you're good. OF course, after we regular people see all the dirty oil we naturally feel like we need to drain it a couple more times before putting in the good stuff. I believe that's where the multiple changes come from. There are videos of people doing this and seeing the oil is still dirty after the second change. So they do one last cheap oil change before using there regular chosen oil.

@donwyoming1936 2 ай бұрын

I bought a used car that definitely has sludge in the pan. Ran full synthetic through the engine for 4 oil changes. Still signs of sludge in the pan on the dip stick after the last oil change. So... she's going to get a dose of Moly next oil change.

@hectorguillen3511 6 ай бұрын

I suggest only using it once in a great while more specifically when sludge or very thick oil is present that with valve cleaner and injector cleaner from Molly

@KingDrewPhilip 4 ай бұрын

I’m tempted to do this with my 2008 Lexus is250 as I heard some good stuff about engine flushes. I really am on the fence with it. The reason why I want to do it is because in the past couple of months I did quite a few really short trips. I know engine oil gets quite dirty if you do those short trips. So maybe it doesn’t hurt to do the engine flush? I haven’t really made up my mind on it.

@MaybeImJustAsian 4 ай бұрын

It’s worth it to do the engine flush in my opinion. I’ve seen how dirty everything gets

@justaregularguy3827 8 ай бұрын

Use fresh oil with any flush to see whats comes out also some dont have viscosity there just detergent and cant fuck up a motor with used moil as it lowers the viscosity and onnused oul its already used and worn for atleast 3k at my dealer

@cosmos2382 Ай бұрын

You were supposed to pour it into a operating temp engine and also your engine needs real fully synthetic which i dont think Liqui moly has, you used half synthetic i think

@ja.935g67 7 ай бұрын

I've seen multiple videos of how you have to do an extra oil change after the flush to flush out the rest of the fluid with fresh oil. Please look it up. They even compared the oil after each drain

@MaybeImJustAsian 7 ай бұрын

Well, I use it based on how it was designed to be used and haven’t had any issues in any of my cars so I’ll keep using it like this. But you are welcome to do an extra oil change as well if it helps you have better peace of mind

@anassnouri6129 Ай бұрын

Why you use 20w50 engine oil ?

@persianhawk682 7 ай бұрын

Hello mate I’ve got a question, it might sound quite funny😁I just used this product in my car and I knew it should be at idle, but as soon as I poured it into the car a minute later of idling the garage asked me if I could reverse back up on the ramp I just reversed probably about a couple of meters if that, Do you think that could cause any slight wear and tear, just a couple of meters probably. less than 6 meter

@MaybeImJustAsian 7 ай бұрын

You should be fine. Just a slow driving will be fine. As long as you didn’t drive it on the street and beat on it, it should be fine

@morfdq Ай бұрын

You don’t need to do this if you change your oil as scheduled. Plus this is a sponsored video

@MaybeImJustAsian Ай бұрын

I personally use all these products in all my cars. And you do you though. I’m not saying you gotta use the stuff ☺️

@PumaM90 Ай бұрын

Maybe he's a big fan of the product

@mr.brightsouls7861 Жыл бұрын

Could you show what comes out? Like with that stuff and without it.

@MaybeImJustAsian Жыл бұрын

It drains and looks just like oil. It basically just goes in the creases and crevices of your engine to grab everything the oil didn’t so that when you put new oil in, it is as clean as it can get

@Theyralltakenfu 8 ай бұрын

@@MaybeImJustAsianIf it doesn’t show when drained, then I’d worry about where it packed itself in my engine.

@Altonivel93 16 күн бұрын

@@Theyralltakenfuit liquifies any gunk so if your old oil is dark you wont notice a difference

@BigDipper79 6 ай бұрын

This is a total waste of money. Engine oil already has cleaners in it. If you change your oil regularly

@MaybeImJustAsian 6 ай бұрын

It’s designed to get rid of more than what oils typically get rid of. It’s not made for everybody in every scenario. What about the people who got cars that weren’t taken care of, rebuilt, or just use it for peace of mind

@sam9776 27 күн бұрын

Sounds just like he just wants to sell products

@MaybeImJustAsian 27 күн бұрын

Funny thing. I don’t get commissions from doing these videos. How is that “just wanting to sell products”? 😂

@Justinas189 4 ай бұрын

But anyway some old oil with flush left inside,its doesn’t effect engine after time?

@MaybeImJustAsian 4 ай бұрын

It will be fine. As long as you have very little amounts in there, it will not be an issue

@balrajvirdi8255 4 ай бұрын

Engine oil started leaking from oil coller and got mixed with radiator fluid, how can i clean colling system. Is liqui molly radior flush good for that. How long can i leave it in the radiator?

@MaybeImJustAsian 4 ай бұрын

So I would say it is good for cleaning up debris and grime from over the years but I’ve never had a personal experience with oil in the radiator. The flush couldn’t hurt as it is designed to get stuff out. But isn’t designed for removing oil out of it specifically

@yasser9350 10 ай бұрын

I never 20w50 existed 😂 what type of would run on it from what i understand 15w and above are for semi trucks and heavy duty

@MaybeImJustAsian 10 ай бұрын

It all depends on your engine build. And yep! Thick oil like that exist (:

@user-fk2mp5xh4s 6 ай бұрын

It was a M.F. to turn over in winter on my V.W.

@bbehzadi413 5 ай бұрын

I’ve seen a few videos where the engine flush requires two oil changes.

@MaybeImJustAsian 5 ай бұрын

Some people do 2 oil changes. But the recommended use is just 1 oil change. As long as you drain it out completely and not a “quick” oil change like most people do

@JGBecknell 10 ай бұрын

Do I need to do two oil changes right after this to get all the residual engine flush chemicals out?

@MaybeImJustAsian 10 ай бұрын

No but I do recommend letting everything drain out as long as possible so there isn’t much in there

@svetlinspirov5869 5 ай бұрын

@@MaybeImJustAsian, yep, I left my car with open drain plug for around 30 minutes, when it no longer drips even a drop, you're good to go.

@Sle3p520 4 ай бұрын

Liqui Moly is life

@MaybeImJustAsian 4 ай бұрын

Yes!!!

@Anthonymvpr 7 ай бұрын

Yooo, 20W50? Wtf, max you should def go is 10W60. Even with built setups.

@MaybeImJustAsian 7 ай бұрын

That’s what the engine builder recommends and has been running so that’s what I’ve always used.

@alvag6 4 ай бұрын

What if i drive it for 5 minutes after i poured it instead of idling?

@MaybeImJustAsian 4 ай бұрын

You should not do that as it puts load on the engine. It isn’t recommended but I couldn’t tell you what could happen if you did that. Just follow the instructions and let it idle and you’ll be fine

@Imadethistocomment13 4 ай бұрын

I am a little bit confused, did you add the flush to the old oil or did you drain the old oil I just let the car run with the flush by itself

@MaybeImJustAsian 4 ай бұрын

You add the flush into the old oil before draining

@Imadethistocomment13 4 ай бұрын

@@MaybeImJustAsian okay thank you, so I added to the old oil and then I drain it after the flush

@sashmilch2305 9 ай бұрын

How is your car doing in winter with that thick oil? I have Toyota celica and it’s burning oil like hell, been driving it on 5w-30 So my plan is to flush the system and put 20w-50 as well

@MaybeImJustAsian 9 ай бұрын

I don’t really drive this car much during winter but as long as you warm it up properly, it’s fine

@initit7070 9 ай бұрын

If your car manufacturer says 5W-30 then do not use any other category of oil, it will completely destroy your engine.

@sashmilch2305 9 ай бұрын

@@initit7070 Ty I checked it and it’s ok for Toyota celica t230

@yourtypicalbot1926 6 ай бұрын

So i dont have to change the oil twice as other people say it??

@MaybeImJustAsian 6 ай бұрын

The exact directions are how I show it in the video. So no. It is not needed as long as you follow it exactly

@islamperce6705 Ай бұрын

How many bottles I need to add on 8cylinder engine?

@MaybeImJustAsian Ай бұрын

Just 1 is fine

@AlexandruNic Ай бұрын

I d suggest 2. It’s one bottle per 5 litres

@samueleyasu3531 Ай бұрын

20w50 the worst oil why not 10w40 5w40?

@MaybeImJustAsian Ай бұрын

My motor and bearing clearances and swapped from a 20w50 And I change my oil every 1000 miles so not a huge deal with what I have going on but k agree, the Molygen and others in the other weights are great!

@ZingChronicles 10 ай бұрын

hey just checking, you just pour it all in or do you take out a quart of oil first, or does it not matter, what did you do ?

@MaybeImJustAsian 10 ай бұрын

You pour it in towards the end of an oil interval so no need to drain anything

@kentaylor5571 9 ай бұрын

just curious but dealerships dont suggest using any flush before an oil change. is there a reason? thanks

@MaybeImJustAsian 9 ай бұрын

You’d have to ask the dealerships that. This gets rid of gunk and grime from your engine. And everybody has preference on additives and stuff like this. I personally use it all and had great luck

@kentaylor5571 9 ай бұрын

@@MaybeImJustAsian thanks sir.

@bean4848 8 ай бұрын

@kentaylor5571 They give that recommendation as a general rule. Some Additives use a formula that's not as seal friendly as others and some might not be strong enough to hold all the deposits in suspension therefore risking it loosening some larger pieces but just move them instead of removing them. LM has built a business heading for 1B in sales & its a good way to measure success. If their products destroyed engines (like some forums would suggest these flushes do) then F1, Moto 2 Moto 3, DTM & other sports events wouldn't want LM near their events.

@MaybeImJustAsian 8 ай бұрын

Well put!

@saltguzzardi 7 ай бұрын

Just wondering do you dump the whole bottle or how much

@MaybeImJustAsian 7 ай бұрын

Yes! The whole bottle is used

@GokuInstinct1 6 ай бұрын

Use a whole bottle per 5 quarts of oil. If your car uses 10 quarts then use two bottles.

@GokuInstinct1 6 ай бұрын

I don’t need to drain any oil first? Won’t the engine flush overfill the engine?

@MaybeImJustAsian 6 ай бұрын

You’re more than likely not going to have the full amount of oil you put in from the start of the oil change. So having a little bit of extra fluid wouldn’t hurt in this case. And it’s not putting load on the engine at all (idle) so it’s not too big of a deal

@GokuInstinct1 6 ай бұрын

@@MaybeImJustAsian very true. I’m going to add this!

@hectorguillen3511 6 ай бұрын

Almost Any engine can be overfilled by half a quart and no more without smoking out the exhaust but from my observation, every vehicle I dealt with from BMW Toyota, and Ford all seem to burn at least one full quart before needing another oil change every 3 to 4.5k miles easily taking that whole Molly cleaner bottle and I suggest only using the cleaner every 5th oil change or rather if sludge oil is present

@E85_STI 10 ай бұрын

I’ve never used anything in my oil but motul but I do change the oil every 2,000 miles so that might be why I don’t need the cleaner but if you car is making power how often are you changing your oil?

@MaybeImJustAsian 10 ай бұрын

I’m doing about every 2000-2500 miles as well. I’m e85 so it’s a good practice to do oil changes more often anyways

@E85_STI 10 ай бұрын

@@MaybeImJustAsian yeah for real that ethanol breaks down the fuel much faster so you already know. Sometimes people say why so early you can go 7000 miles and I tell them it doesn’t work like that with this type of build. Now I do have a 2008 Acura tl type s that’s a daily driver so I might try this additive to see what’s up. I used to have a 2008 EVO VIII it was a fun car

@MaybeImJustAsian 10 ай бұрын

@@E85_STI the engine flush works with everything and does help clean out the extra gunk that has built up over the years regardless of how regularly you maintain your cars

@E85_STI 10 ай бұрын

@@MaybeImJustAsian nice well great video and I’m curious about it and I will throw some in my Acura for sure.

@MaybeImJustAsian 10 ай бұрын

@@E85_STI thank you! You’ll love it

@philipjohn1338 7 ай бұрын

Does it work for GDI engines?

@MaybeImJustAsian 7 ай бұрын

Yes it does!

@raccdaddyy368 9 ай бұрын

what if its to the point my engine won't start? how would i go about flushing it then?

@MaybeImJustAsian 9 ай бұрын

Wouldn’t be possible with this. Depends on what the reason is that your engine won’t start. This isn’t a fix all remedy for stuff. It’s to properly maintain engines so they don’t get that far

@raccdaddyy368 9 ай бұрын

@@MaybeImJustAsian was pretty late on my last oil change and the guy said i needed a flush but didn't have the money at the time, so its from a build up of sludge :/

@MaybeImJustAsian 9 ай бұрын

Now that’s unfortunate :( That’s why this product exists. To not allow that to happen

@T_733 9 ай бұрын

So you add it before u change the oil

@gazzy555joker6 2 ай бұрын

How many ml do I add to certain ml engines crap instructions tbh

@MaybeImJustAsian 2 ай бұрын

The whole bottle?

@pedronobre4896 6 ай бұрын

Do you put the flush every oil change ?

@MaybeImJustAsian 6 ай бұрын

I don’t use it every change but I know some shops that do flush with every change

@pedronobre4896 6 ай бұрын

@@MaybeImJustAsian that's a new for me , i will try it on my daily as she,s going to 879k km original block and head

@GokuInstinct1 6 ай бұрын

Liqui Moly recommends every 25k miles. I would personally only do it once if the oil changes weren't done on time or if you got the car used and don't know the history. I'm doing it on a used car I got at 52k miles. It's coming up on 61k miles and I figured why not clean the engine since I have no idea what the previous owner did. Once it's clean just religiously change the oil every 5k miles/6 months. You can go for longer if you're only driving highway miles though.

@pedronobre4896 6 ай бұрын

@@GokuInstinct1 exacly what i already do on my 2 cars , 1 focus petrol 80% city km i do change 7,500km oil n filters My work daily is almost on 900 k km and probably 75% higway km , i do change it before 10 .000km if i can i do it at 8 . Always since new liqui moly with mann filters , never flush it or ceratec , just fresh oil and heavy wheight labor tools on it , dosnt need to add oil between changes , i think she's good legs and heart 🤣

@BoharieBob-iu9wc 9 ай бұрын

Using liquimoly flush , is it every time we want to change engine oil?..

@MaybeImJustAsian 9 ай бұрын

Some people do every oil change some people do it once a year It really depends on how many miles and how much sludge is in your engine

@Amokof 5 ай бұрын

As long as you do your oil changes on time and use synthetic oil, you wouldn’t need to use any of these additives. Modern synthetic oil has detergents to clean out the old oil. Using engine flushes like the one in the video is fine if you’ve neglected your car for a while or if you’re buying a car with an unknown service history. Just make sure to not use it on a high milage car with unknown service history. Because if they haven’t changed the oil in a long time, there is probably going to be a lot of gunk and sludge build up inside. And if you do loosen the sludge with a chemical engine flush, they’ll probably clog up something in the engine like an oil pump screen for example. The safest way to flush an engine is to dump your old oil and filter and replace them with a new cheap synthetic oil and filter. Drive for 500 miles and then dump the oil and filter. Repeat the process 2 more times. On your third and last time, use a high quality synthetic oil and filter. Yes this method might be slightly expensive than using a Liqui moly engine flush, but it depends on how much you value your car. If you care for your car and want it in the best condition, use the safe method. If you got a beater car and dont want to spend much on it, use the liqui moly engine flush.

@Garlander 4 ай бұрын

Their website says to do it every 25k miles.

@JR.2024 7 ай бұрын

Is this the same seafoam does?

@MaybeImJustAsian 7 ай бұрын

No. They are two completely different formulations with different uses

@danemaloney719 6 ай бұрын

You sound like an ad.

@MaybeImJustAsian 6 ай бұрын

😂😂 I mean. It kinda is?

@lucpaquin6025 10 ай бұрын

That stuff will be in your bearings and everywhere you don’t want, bad idea.

@MaybeImJustAsian 10 ай бұрын

My guy, that’s why you drain it 😂 And yeah, a whole company and tons of people I know personally use it and their businesses are built on this stuff. You don’t have to understand but there’s a reason why Liqui Moly is used in so many cars and by so many race teams in the world.

@officialamanvirk1912 5 ай бұрын

Product of link plz

@MaybeImJustAsian 5 ай бұрын

You can find these bottles in most auto parts stores like advance auto/autozone/oreilys etc And online at FCP Euro and ECSTuning

@enriqueparedespinel1694 7 ай бұрын

Is it bad to run the engine for 1 hole day with that liquid?

@MaybeImJustAsian 7 ай бұрын

We do not recommend doing that as you don’t need to put load on the engine with that fluid in it

@Amokof 4 ай бұрын

Yes, it should just let it idle in the engine for 10 mins and then dump it out. Dont rev the engine, just let it idle.

@IndiansAuto 7 ай бұрын

Tbh. This is useless. If you have a race car you should be changing oil quite often. No need to flush.

@MaybeImJustAsian 7 ай бұрын

Changing oil often doesn’t mean it’s always clean. And this is more designed for cars that see the road and don’t have an oil change every race.

@IndiansAuto 7 ай бұрын

@@MaybeImJustAsian what are you trying to flush out? You should have a catch can. You’re not really getting any trash in the motor

@Michal_S0L 10 ай бұрын

do it with the engine up to temp

@MaybeImJustAsian 10 ай бұрын

The engine will also get up to temps in the 10-15 minutes but thank you! I did have mine up to temps before doing it

@buttsexandbananapeels 7 ай бұрын

Second this. The evaporation point of the carrier fluid (probably kerosene) is around 140. When it vaporizes, it helps work into the piston rings to help remove any coking.