Derek shows us in part 2 how to bend offset bends in 15mm copper tube using a pipe bender.
Пікірлер: 32
@phasedout67694 жыл бұрын
Honestly the most helpful video on bending I've seen. Hats off. Time to mark my bender 👍
@mikebarron49293 жыл бұрын
I've been plumbing 37 years and I've not long found your channel and can say honestly if all tutors were as straight to the point and clear in there instructions as yourself then the training industry would be much improved your vids are spot on with little faff and lots of good knowledge
@tomkatgastraining3 жыл бұрын
Thanks for your comment and watching cheers
@saleh89443 жыл бұрын
To the thumbs down folk who obviously didn't understand or fully appreciate the best pipe bending videos out there: I would suggest you pay someone to do it for you as Derek is far and away the best instructor on this subject :)
@hdhanji80064 жыл бұрын
Great tips thrown in Derek... measured properly with no unnecessary pipe wastage 👍
@mohammednadeem72743 жыл бұрын
Another well presented video with very valuable tips to help with the pipe bending, I love the drawing with the angles, the solder was a well cool tip to get the bends and angles correct. An excellent video once again derek.
@mj0n4id363 жыл бұрын
Truly amazing. Great tips given by a great teacher. The making use of a template and solder is genius. Marking out the centre of the pipe was a great tip too. I’m going to create a template, laminate it and keep it with my pipe bender. Thanks Derek 👍🏻 Asian Jon. Training.
@Agopper4 жыл бұрын
Great learning video as usual and thanks for for sharing your knowledge to newcomers, all your video are very educational for new entries in the trade cheers derek
@johnswilley67642 жыл бұрын
Thank you Sir! I'm going through your videos, just got to #2, getting ready to make a Cu pipe dryer/receiver setup for my compressor. You have produced an excellent stock of info. From Orlando, Florida, U.S.A. thanks again, and best wishes!
@MarcusT863 жыл бұрын
Thanks for taking the time to make these. Great stuff mate!
@AJ-cw9rb3 жыл бұрын
As always Derek, great Video, keep it up mate 👍
@davyogi97963 жыл бұрын
Thanks Derek, at least you have shown that sometime we can over bend the pipe, marking the bender and another great tip, a bit different to when I was tault with 2 metal folding rules.
@rivkiroyde43624 жыл бұрын
Thanks Derek great video 👍👍👍
@willlomas27252 жыл бұрын
Very informative Derek .....Thanks.
@joebaikaikamara75099 ай бұрын
Great tutorial lesson
@monikanader94543 жыл бұрын
Another great video👍
@fredjennings92684 жыл бұрын
Informative... thanks for giving you time👍
@ashkanrajabzadeh96324 жыл бұрын
That’s perfect boss
@rotarurazvan87923 жыл бұрын
You are great, clever...
@TheRumpusView2 жыл бұрын
Thanks very much for this. It is just what I need, except I need to do a 60mm offset on 22mm pipe. I need to work out what the minimum offset is, I hope that a 30 degree bend is possible. Good camera work here. Well done.
@TheDickPuller4 жыл бұрын
Very informative as always Del. Know what I was impressed by most - that fucking Silverline bending machine, it looks the Dog’s Bollox!! I guess for the course cowboys & career change chancers you can only buy cheap tools. Of course for speed on-site, you don’t have time to draw lines. For a parallel line stick the pipe against the Skirting & measure/mark from that. Another wee tip; use a bit of core solder to get the complete offset size, centre to centre, then use that on yer Bender.
@allanfuller72932 жыл бұрын
Please tell me what pipe thickness you use. I bought a Rothenberger Multi-Bender and when I bend pipe it cracks. I want to start practicing pipe bending. Thank you
@1Monaghan4 жыл бұрын
Oh no the dreaded saddle bend next
@creditlink3 жыл бұрын
Hi is this really a 30degree angle because it looks more like 150degree?
@jamiel64823 жыл бұрын
yes lads
@markroberts68643 жыл бұрын
Cheers
@Dreancaidi2 жыл бұрын
How do you bend 1 inch copper pipe?
@koliakolian8102 жыл бұрын
Good
@patricklynch2731 Жыл бұрын
Does anyone show how to bend 22mm pipe. What measurement do you come back to pull a 90deg
@davidjingga83562 жыл бұрын
Hi, does anyone know how to bend flat copper pipes? I understand I'd have to stuff the flat copper pipes with, like, fine sand so that kinks won't form when bending. But is there a specific tool to bend flat copper pipes with?