Thanks for the update. Waiting for mine to arrive... nice to get good info so as to avoid the beast being out of action for months due to lack of spares

I sheared off 3 of those diff screws already, all in the front diff. It seems to be the only weakness on mine. My wltoys 12428-B came with all metal gears stock, except spur. Great car! Nice vids!

Oops broke it! Lol to much power for that lil guy! Great video brotha!

Waiting for the next video with the bigger wheels. :)

I always say - anything on this car held together with that dreaded M2*8 screw needs to be changed, or have a spare ready - and anything linked to it!. Its a rubbish screw used all over that drive train, impossible to remove without breaking. Good luck

Nice video!! Where are you getting the spares/upgrades from? My lad has one and needs the rear centre drive shaft and new front diff casing. Tia.

Skate park doing what it does best! :P

I had this same issue. I ended up drilling all the way through and used larger screws and locking nuts. Never broke another since.

Hello, quick question,i am also using a BL MOTOR 3650 4 poles 3900KV a 60A esc, and for the receiver a Flysky A3. I am using the original battery that came with this, but i had to change the controller.i Also bought a 2200 2 Cell lipo. i swapped now 3 controllers as i have a serious problem.Sometimes when i accelerate it does not stop.Just goes . Can you tell me what battery are you using and Controller please?

That bent shaft will cause vibration for sure. Change it at some point I would.

Love this car, it's perfect if I'm not feeling in a 'Bison' mood. haven't done any mods on mine apart from sorting out the wild amount of toe-out. Some great tips in here Tomley. Subscribed. 👍🏼 Oh, recommendations for a spare battery?

Hi thanks for this update .. and i have a question can you tell me what else i need to change if i buy this brushless motor with this esc ??

how did you get out the broken off screw?

hey man was wondering how much run time you were getting?

Good video! The driveshaft on mine is loose and it slips. It only has torque on the front wheels

I have the 12423 and after going to 2s lipo on the stock drive line it grenaded the rear diff. Replaced that then the next run the front diff grenaded so I ripped it the from drive shaft and pinion gear so its 2wd now.. and honestly it's more fun.. faster and does way cooler things on dirt

Even with stock electronics, i also got bent drive shaft.. I straightened them up but still comes bent after few runs.

Hey man I know you are super busy with all the mad stuff you do but I have one of these and I'm trying to make it mentally fast, could you put a 5500+kv motor in? I'm currently on a 3500kv motor(waiting on my 4500kv motor to arrive) just want to see a speed test on it with high kv motor

Hey bud, where did you buy the parts from? I need a Spur for my car. Thanks

Where is the drive shaft from?

😲she exploded! Looks like you gave it a bit to much in the bashing department! Fix her up!

Loctite 603/609 green "retaining compound" "Application: Slip Fitted Parts " Its made for baring shafts to hold bearings in place it wont come un-done! Green Loctite will fix your metal diff gear.

Sir, is it possible to upgrade to brushless system even if i use the same stock radio controller and receiver? Please reply. Thank u

i think you should lock your rear diff. You`re not racing you`re just bashing, it will be more aggressive and more power to the rear end. this thing does have a slipper clutch right?

Glad you traced the problem. Could you post a link to the metal diff and gearbox parts that you used?

Of all the components that heavy nose-dive might have trashed, I´d never have guessed it´d be the motor... I´ve just come from my local RC shop - he has these very cars on display, marked up at 118 quid!

Does URS stall when the battery is on low?

Hi there, is wltoys 12428 better than a jjrc q46?

Ya must throw that off a ruff or something cause I couldn’t brake mine even when I tried

I don't know. Out of the box the whole drive-train wobbles. On 2S these CVDs bend like butter, already. On 3S one of mine broke. Seems to be this "pressed" powder metal? They should make them more expensive and beefier. Kinda frustrating to bend them back after almost every outing. Let's see what breaks next! For a child only running this on 2S this is the best car imo. But for a brushless system some parts need a revision. The quality of the budget 1/10th HSP cars is far better, drive-train - wise. But this "chewing gum" - plastic of Wltoys, Xinlehong and so on is almost a miracle. I showed the Wltoys to a neighbor, threw it in a very bad angle down on the concrete and he was sure something broke! Nothing broke, LOL.

the truck isnt designed for taking jumps like that...due to the geometry and lack of a bumper. Plus a 3650 motor is on the over power side on 1/12 ....Lack of a sliper clutch dosnt help. There's only a 2845 3000 KV in my Fy03. it has plenty of power. It'll do back flip from a stand still ( on pavement) if I gun it on 3s. It'll pop wheelies on 2 s on grass. it's still fast on 2 or 3s. The Fy03 front cvd actuate in and out..to prevent bending and binding...The fy03 also has a sliper clutch...it slip a little so it wont strip on braking or hard torquing. I even mounted KT-12 wheels and tires...they're slight taller ..and 1 3/4 wide. The tires also acts like a cushion or shock absorber....( it helps) Even so,....I still wont launch it off a big ramp..it's just asking for trouble or parts to break. I like my fy03..it's still in one piece...drives great.. It's not desiign to do that,,...There;s lights on the roof rack...lmao People launching off of bmx or skatboard ramps are doing it on truggie or BUGGY PAN style designed...it's not as high...Plus the PAN SLAPPs the ground to absorb the impac ..preventing over bending of the A -arms...Plus a bumper will also help.....but it'll suck for CRAWLING. The wheels stick out further than the bumper. The 12428 or Fy03 can rock crawl and semi jumps,...short course type driving. The dogbone will bend or jam the cups into the diff....which will cuase those screw to come loose on hard landing or cart wheels ..it happens on my other 1/10 truggie R/C ( dogbone bending)... it is what it is....sometimes it'll simply just rips the dogbone from the cup... nothing breaks...you just pop it back in.... other times ..it'll shove it into the di'ff cups....i get some sort of binding noise from the diff.lol

El motor Brushless necesita cambiar todo por piezas de metal coronas cardan piñones diferencial de lo contrario al primer esfuerzo se romperan las piezas

Why not buy an aluminum gear?