Tools needed to install vinyl siding

Рет қаралды 3,032

Күн бұрын

These are all the hand tools that I use on a daily bases to install vinyl siding. Also I’m including a somewhat in depth review of how to use them and the benefits and drawbacks of each one. (90-33.75=56.25 not 66.25.... oops lol) And if my voice sounds funny it’s because I’m getting over a cold.
Amazon affiliate links to the hand tools I use:
Fat max tape measure amzn.to/3ZF9ROI
(Expensive but nice) Stiletto hammer amzn.to/3waImyV
or
(More affordable) Estwing hammer 16oz
amzn.to/3QCKKrX
Carpenter pencils amzn.to/3QEO4T8
Sharpie markers amzn.to/3IKxG1H
Empire speed square amzn.to/3kmDxQo
Irwin chalk line amzn.to/3iyfRbD
Andy 3” siding snips amzn.to/3QD05Zv
Malco siding removal zip tool amzn.to/3COkLrw
Malco snap lock punch amzn.to/3Ws0f7r
Malco trim nail punch amzn.to/3XxU6ra
Malco nail slot punch amzn.to/3ZzKxtr
Malco hand seamers amzn.to/3COWhhT
(A little pricey) Occidental tool belt I use amzn.to/3QD0lYs
or
(More affordable) AWP Tool belt amzn.to/3XtstiS
Empire 10” Torpedo Level amzn.to/3GK9nhx
Lenox Gold utility knife amzn.to/3CO4L94
Buck Brothers chisel set amzn.to/3IM6Bez
Equipment:
Tapco Pro 19 - 12’6” x 19” brake amzn.to/3kdYI7o
Tapco Snap Stand amzn.to/3CPDzqA
Tapco side winder amzn.to/3XcKRge
Tapco pro cut off wheel amzn.to/3XfW2EU
Tapco brake buddy amzn.to/3kdZfGq
Tapco ProTrax siding saw amzn.to/3Xep7Av
Makita dual battery framing saw amzn.to/3H6xI2M
Irwin vinyl siding saw blade amzn.to/3kgDdmy
--------------------Contents of Video----------------------
00:00 - Introduction
00:50 - Occidental Finish Carpenter nail bags
03:22 - 16 oz hammer
03:54 - Lenox Gold utility knife
05:50 - Siding removal tool
07:07 - Chisel
07:34 - Chalk line
08:04 - Markers
08:37 - Malco Slot Punch tool
09:33 - Malco Hand Seamers
09:56 - Malco 3" "Andy" siding shears
12:43 - Malco Snap Lock Punch
15:34 - Irwin 10" torpedo level
16:40 - Stanley Fat Max tape measure
17:39 - Empire speed square
18:56 - Kobalt trim nail punch
20:09 - Makita saw & Irwin vinyl siding blade
21:12 - Paslode siding staplers... The End

Пікірлер: 15

@sidingschool Жыл бұрын

Amazon affiliate links to the tools I use: Fat max tape measure amzn.to/3ZF9ROI (Expensive but nice) Stiletto hammer amzn.to/3waImyV -or- (More affordable) Estwing hammer 16oz amzn.to/3QCKKrX Carpenter pencils amzn.to/3QEO4T8 Sharpie markers amzn.to/3IKxG1H Empire speed square amzn.to/3kmDxQo Irwin chalk line amzn.to/3iyfRbD Andy 3” siding snips amzn.to/3QD05Zv Malco siding removal zip tool amzn.to/3COkLrw Malco snap lock punch amzn.to/3Ws0f7r Malco trim nail punch amzn.to/3XxU6ra Malco nail slot punch amzn.to/3ZzKxtr Malco hand seamers amzn.to/3COWhhT (A little pricey) Occidental tool belt I use amzn.to/3QD0lYs -or- (More affordable) AWP Tool belt amzn.to/3XtstiS Empire 10” Torpedo Level amzn.to/3GK9nhx Lenox Gold utility knife amzn.to/3CO4L94 Buck Brothers chisel set amzn.to/3IM6Bez Equipment: Tapco Pro 19 - 12’6” x 19” brake amzn.to/3kdYI7o Tapco Snap Stand amzn.to/3CPDzqA Tapco side winder amzn.to/3XcKRge Tapco pro cut off wheel amzn.to/3XfW2EU Tapco brake buddy amzn.to/3kdZfGq Tapco ProTrax siding saw amzn.to/3Xep7Av Makita dual battery framing saw amzn.to/3H6xI2M Irwin vinyl siding saw blade amzn.to/3kgDdmy

@SteveRobReviews Жыл бұрын

Hi Brandon Very informative channel . I'm looking at learning how to install siding and your channel is so helpful. Look at seeing more . Thanks 👍

@sidingschool Жыл бұрын

You’re welcome!

@stevepicchi8986 Жыл бұрын

I really appreciate the time you spent going over your tool choices. At some point could you do a video on job cost and material estimating. Thank you!

@sidingschool Жыл бұрын

Hi Steve, I do plan to make a video on material estimating. Job cost is a little harder because it depends where people live and what kind of lifestyle they have, but I’ll probably go over that at some point as well. More videos to come!

@stevepicchi8986 Жыл бұрын

@@sidingschool awesome bro! I can’t wait

@JohnVargas-ie6dc Жыл бұрын

I like your Makita Skil saw vinyl blade. You should try a diamond blade. It won’t chip your siding and it’s easier on the ears.

@sidingschool Жыл бұрын

I tried a diamond blade once and didn’t have very good luck with it (it seemed to cut slow and was loud). Maybe I tried the wrong kind… what kind do you use? If the material doesn’t bind this vinyl blade does not tend to chip siding even at lower temps, (but you can’t force the blade through you have to let it do the work).

@mr.jj575 Жыл бұрын

Interesting set up.. I invested in a 5 gallon organizer to put like the nails, chalk line, any other tools that I don't really need till I get to a specific part..ain't trying to carry all that weight all day..

@sidingschool Жыл бұрын

I hear you there. Despite my bags being comfortable I still have bruises. And it’s definitely worth putting chalk lines away when it’s raining, otherwise they are garbage after one day. I’m still going for speed so I prefer to keep a lot of tools on me unfortunately. Maybe some day I’ll try out the bucket idea. :)

@audleyboyd1 9 ай бұрын

Having a hard time finding a solution for fastening would love to use a stapler( hard to find) do you just use 18 ga narrow crown staples for soffit? Would you use a cordless 18 ga for soffit? Model # for paslode ? Any help would greatly be appreciated. I'm on my third house nailing by hand its getting old and slow. Any help 🙏 thanks in advance. Love the way you join j channel I now use your technique. Thank you. I text you recently about finishing siding at the top of a wall where the nail flange was deep in the j channel I ended up trimming 1 inch off the bottom and silicone the pieces in place to finish the look so the nail flange wasn't exposed at the top of the wall

@sidingschool 9 ай бұрын

Hi Chris, I would use an 18 gauge staple on soffit (just note that it might not meet specifications). I only know of 1 place to get the Paslode SCS200 with a vinyl siding tip and they won’t ship. I can get one and send it out to you for $425 plus shipping (it might take a couple weeks, fyi).

@audleyboyd1 9 ай бұрын

@sidingschool thanks for the info after next job may take you up on the stapler. One more question if you don't mind. I noticed that you put something in your snap stand as a material holder what did you use anything specific or just whatever you can jam in there?

@sidingschool 9 ай бұрын

@audleyboyd1 For the material holder I just found a random piece of 1/2” rebar about 2’6” and threaded it through… I could only find one rebar so the other side I ripped a piece of strapping down to about 3/4”x3/4”.

@audleyboyd1 9 ай бұрын

Thanks appreciate your videos. Watched several so far