We LIFTED the $400 Project Blazer! S10 Blazer Build Starts NOW!

No video

We LIFTED the $400 Project Blazer! S10 Blazer Build Starts NOW!

Рет қаралды 31,039

Күн бұрын

Today we started to tackle the 1989 S10 T10 Blazer build!
Merchandise: teespring.com/...
Follow me on Instagram @TopLineRacer
Email me: TopLineRacer@gmail.com

Пікірлер: 50

@TopLineRacer 4 жыл бұрын

Give me ideas for the build down below! What would you like to see?

@nomorecontent5404 4 жыл бұрын

No put super swamper tires on it

@TopLineRacer 4 жыл бұрын

Haha I would but I plan to drive this regularly. If I turn it into a full offraoder then I may give that route.

@Mmike9231 4 жыл бұрын

Great video man. My brother and I have been restoring an S10 94 Blazer since may. Definitely going to lift it. One thing you might want to consider is converting the dash into the digital one. I just did ours and it looks great. We live in PA too!

@risitiaina2965 4 жыл бұрын

You guys should do a Gambler in it :)

@JA-rn5qv 4 жыл бұрын

Maybe before you do any more suspension mods you take care of all that rust. Plenty of good instructional vids on YT on how to do it. *Tip - whenever you're gonna be working on suspension or any bolts that tend to seize, plan a bit ahead and spray penetrating lubricant on all the nuts/bolts the day before you are going to be doing the work. Each time you apply the lubricant tap all around the nut/bolt area (a tack hammer works best) to help break the chemical bond that's created during the rust process. Keep the treated area warm after applying the penetrating lubricant, at least 75 degrees for the 24 hour treatment. You can always use an electric heating pad or heat lamps. The prolonged heat treatment will help the lubricant penetrate deeper in to the metal. The next day after you've done the initial 24 hr soak, once again tap all around the area that you treated, then apply one last good soaking of the lubricant, wait 1 hour, then you are good to start the nut/bolt removal process. When it comes to inexpensive brands, Liquid Wrench is your best bet for a penetrating lubricants. Those few easy steps will save you hours of frustration and lots of skinned knuckles not to mention having to replace parts. I like your garage/shop set-up. Where l live in the U.S. you gotta be rich to have a 2 car garage like that. The Blazer looks much better with that lift, as if that's how it should have come from the factory in the first place!

@Mike_The_Hog_A_Nator Жыл бұрын

My buddy rolled his & got $15 from GM then died but I love that year model. I have an 02' Blazer ZR2 & love it. Especially for $3k that I paid for it 6yrs ago & it was garage kept, know one ever sat in the passenger & rear seats. Super clean.

@hudsonhawk0016 4 жыл бұрын

Ya got the gas tank nice and hot, yikes!

@emanuelnamseth1469 4 жыл бұрын

Those old s10 blazers are looking sharp. And the new blazer is NOT a blazer.

@er1115 2 жыл бұрын

100%

@Thatlow_Slow5.3 3 ай бұрын

Ummm what’s wrong with the 99 the 05 body style i love the 2 door personally only

@redwolfmaddox3986 3 ай бұрын

RC makes a 6 inch kit if your interested

@clarissacastro6552 Жыл бұрын

I miss my 89 blazer s10

@thedivineeagle377 3 жыл бұрын

Me watching the gas tank heat up 👁️👄👁️

@michaelwhite8493 3 жыл бұрын

That trans leak might be the output shaft seal on the trans. It leaks into the transfer case and fills it up till it overflows out of the vent. Mine did that.

@TopLineRacer 3 жыл бұрын

I appreciate the info. Honestly, I just stopped topping it off and it has run perfect now for about a year.

@larryalexander4833 4 жыл бұрын

The reason it has to turn over a second to start is. Gm set it up to build oil pressure before it will start .

@captainjerk 4 жыл бұрын

9:17 I think we gotta go second hole.

@hudsonhawk0016 4 жыл бұрын

🤣🤣🤣

@tylerdavis4459 4 жыл бұрын

31s with fit on a stock s10

@Taggemz 3 жыл бұрын

True but they will rub in the front when turning

@theaidenflow2035 3 жыл бұрын

Very helpful 💪

@chrisgossman4522 4 жыл бұрын

Just my opinion, powder coat the steel wheels black with the original center caps.

@towtruckdriver1000 3 жыл бұрын

I went 3 lift shackle same style as yours my truck went skyward

@electricguysvcs 4 жыл бұрын

I changed my bushings last year while putting on those same shackles on my ZR2. Needless to say, the rear was on a lift for a few days. PB blaster and a lot of hammering. Like the pully removal idea.

@TopLineRacer 4 жыл бұрын

They are a son of a gun to get out! The puller worked decent but still was a pretty tough project. Thanks for watching!

@DylanYouSonOfABidgeNelson 4 жыл бұрын

I bought a 1991 2 door 4 wheel drive for $300, and I must say, that beep before you start it is AGGRAVATING.

@TopLineRacer 4 жыл бұрын

Haha, its not great.

@frenchtickler915 2 жыл бұрын

Hey bud I just bought a 92 2door 4wd for $400. I'm new to the s10 blazer scene been learning all I can but I got some questions If you ever actually read this. Since you've had yours a lot longer you might could give me some pointers.

@joeywetzel5616 2 жыл бұрын

@@TopLineRacer i took beep away

@towtruckdriver1000 3 жыл бұрын

Do a three inch body lift

@000MACK000 Жыл бұрын

So did you go with the 235 75 R15 if so did it rub? cuz that's the size I went with and it rubs like crazy but I haven't done my lift yet and by the way mine starts the same way as yours it takes a few seconds.