Your instructions here enabled a 14 year old carer to do this job for her disabled mum. Many thanks from two families.
@AC-mh1qf29 күн бұрын
Thank you boss, i was having existential crisis before fixing it using this video
@deschumber659Ай бұрын
Lots and lots of videos but this one explains the best.Thank you
@ts.nathan7786 Жыл бұрын
I have seen many videos about the ball valve. But you are the only one who explained about the notch in the valve. Congrats.
@nicklancaster3348 Жыл бұрын
Lifesaver! After a frustrating half hour trying to reassemble the valve, I found your video! Job done in minutes! Thank you!
@steveturner65288 жыл бұрын
Thanks, very useful. Followed closely and even realised I had one with the metal pin. Would have not realised that without your kind video.What I didn't spot is the little rubber plug had dropped out of the new arm. Assembled everything but water did not stop. When I saw the plug lying on the table I realised where it went - needed to block hole in the valve. Reassembled it and everything worked well. Here's looking to another 21 years of reliable operation!
@leejamieson27957 жыл бұрын
Water inlet wouldn't fully stop even when float was fully raised. Changed the diaphragm but no change. Read your post and checked the tiny black rubber plug/seal and found it to be worn, so took it out, reversed it and put it back in the hole. Put it all back together, turned the water back on and it's working just fine! 😊
@Smiler7 Жыл бұрын
Excellent! Thank you! I had a slow filling tank with this fitting. I noticed when the tank was slowly filling (5 minutes) water was squirting out where the arm meets the valve. I stripped it down, as per your guidance. It all looked pretty clean, but I cleaned it anyway. I put it back together, making sure the notches were aligned. It all worked great, but then I decided to adjust the float. In doing so I must have moved it out of the notches, although it was hand tight. So I unscrewed it and refitted it to the notches and, touch wood, it is fine again.
@brsince7810 жыл бұрын
Thankyou. Panic stations here until I watched this, diverted my wife's journey home via B&Q to buy a new diaphragm. 10 minutes after she got home - job done!
@StevenBrandist8 жыл бұрын
Many thanks. Helped greatly with a fault on ours. Thought it was the diaphragm, but ended up being a clogged filter in the inlet tube, it reduced the pressure so the valve never shut off.
@nusssain2 жыл бұрын
Thank you very much mate, you are a life saver. Excellent video excellent explanation 👍🏼
@joehodgkinson94379 жыл бұрын
Many thanks! Been shouting at the cistern for a couple of hours before finding your video. Fixed in five mins.
@sylviadonohue60029 жыл бұрын
I cant thankyou enough my husband and myself have been struggling to fix this valve after watching your video presto its done in no time ( top Man)
@gwill46102 жыл бұрын
Thank you so much for this extremely detailed and helpful video. This is exactly what I was looking for has having issues with the diaphragm in a new toilet excellent instruction.
@jayvee040410 жыл бұрын
Thanks for posting this. Big, Big help when I had to take off the float arm from new valve (just fitted) to check what was causing a constant drip from the blue nut at the top. Probably hadn't put it together correctly at the start. All seems OK now. Cheers MrCrass :-).... Hope Lisa managed OK!
@clickandprayphotography6 жыл бұрын
I've been struggling to get a plumber to replace my fill valve but after seeing this I realise I may be able to fix it myself ... thanks!!
@robchristie52317 жыл бұрын
Well explained, thanks. It takes a few seconds when the float has got to the top to build up pressure to turn the flow off, that stumped me for a while as I was doing it by hand and being too impatient
@MrDuncl7 жыл бұрын
Thank You. I fitted the top half of a new valve onto the stem of an old one. Without your explanation about removing the little plastic pin I would have been stuck. p.s, I ended up using the old float and filling tube as the new ones were bigger and fouled the syphon and tank side.
@beermeupscottie10 жыл бұрын
Hey thanks. Your video for Lisa helped me clean and reassemble my Torbeck valve and stop a slow continuous overfill :)
@janeangus10110 жыл бұрын
Thank you great help. Having forgetting which way it went in , and not realising it had to click into place eventually found your video and 5 min job. I could kiss ya !!
@alm5966 Жыл бұрын
I'm not a plumber but I managed to fit a Torbeck valve in a small cistern. What I can say is buy a new diaphragm as the one supplied was useless. It started dripping after a few days and it's because the diaphragm is not for purpose. They're a couple of quid and will save you a serious headache.
@lauramurray34768 жыл бұрын
Thank you! This helped me replace the washer and fix the problem in 5 minutes!
@Shhtteeve6 жыл бұрын
great guide, going to have a tinker tomorrow before work.
@davidrod84125 жыл бұрын
brilliant clear calm and kool instructions thanks
@MrCrass3611 жыл бұрын
Hi, the nozzle on top which directs the water down into cistern has most likely become brittle with age. This causes cracks around the moulded edges of nozzle. you will have to get a new float valve. If the valve itself is operating correctly then just change the top nozzle over and save the rest of the valve for a later date. To get the nozzle off undo the blue nut slightly and pull off the nozzle. The nozzle has a small lip on it which holds it in place when you re-tighten the nut
@johnliverpool36056 жыл бұрын
Thank you very much this really helped me, even the detail of the pin
@liammack36353 жыл бұрын
This helped me , thank you.
@Greenjuiceman9 жыл бұрын
you are the mostest kindest
@RC-cs3me3 жыл бұрын
Thank you so much 👍👍👍👍
@pauladamson67008 жыл бұрын
Many thanks for this video. I thought I was going to have to call a plumber - even I can do this job :-)
@kimmib653811 жыл бұрын
I have one of these valves in my toilet and the water has started spraying from the top (square holes next to the arm thing @ 0:06) of the valve when I flush the toilet which then leaks out of the cistern soaking my bathroom floor. Can you give me an idea what's wrong?
@Ragran6 ай бұрын
I'm not Lisa but thank you for this
@1948trevor10 жыл бұрын
Actually a complete unit will cost you about the same as a diaphragm+pp and it is a good idea to replace the whole thing, apart from the basic connection. As Mr Crass says, the stuff gets brittle.
@jimwebb33463 жыл бұрын
Just got a new diaphragm from Toolstation for £2.93
@clivepownceby3 жыл бұрын
Can I ask whether a worn diaphragm would cause the toilet to fill constantly until the flow eventually stops? Sometimes it can take 5 minutes! This is my current problem.
@1948trevor10 жыл бұрын
If your unit has a steel pin but the diaphragm is the type that does not have a grommet, remove the pin and place the new diaphragm with the little plastic peg at 6 o'clock. Opella stopped fitting the steel pins about 5 years ago. Check your unit before you go shopping because if you get the older type it won't work on the newer design,
@philhurst11829 ай бұрын
My valve was a simple one but had an odd characteric. It doesn't work like a normal ball cock. You can't waggle it and turn the water feed on and off. It will only shut off when the cistern fills to the very top. Don't ask me why. I spent a couple of hours taking the damn thing apart and reassembling it, thinking it was defective.
@Funguspunt6 жыл бұрын
Great video, I have an older one with pin so have taken the plug out of the new washer. However, when reassembled I just cant get teh water to run. Driving me mad, must be a simple answer.
@timmoore4372 Жыл бұрын
Did you sort this, I have the same problem.
@blackrainb0w6 жыл бұрын
+1 You helped me save £70. thx very much.
@martnal6 жыл бұрын
My problem was that the white square plug divided into 4, just behind the top blue screw nut had come out. I'm going to try and dry everything and glue it in with superglue.
@adamspark42893 жыл бұрын
Can you replace this washer without having to take it out of the cistern?
@David-lb4te4 жыл бұрын
2:25. but then you proceed to fit the diaphragm without the plastic pin, into a housing that requires one!? You explained that the small plastic pin is using in housing without a metal pin, and the diaphragm with a plastic pin is for housing without a blue plastic insert and metal pin? Confused.
@jimwebb33463 жыл бұрын
Confused me too
@MrKurdishpride1007 жыл бұрын
Thanks for this video mate
@robertkacala7 жыл бұрын
iv got with the plastic filter and new washer but the water doesn't wanna run
@garrynutter86011 жыл бұрын
You took out the little pin, But didn't put it back. Does the little pin go in the little hole. Will it work without it. Maybe you could do another video with the pin. Garry
@anthonybenning21546 жыл бұрын
Great
@jeremyjenkins38626 жыл бұрын
Yes, a valid point which foxed me too. You do need the plastic pin in as he says (but does not do) or it doesn't work. Also, don't make the mistake I did and try to poke the small pin into the small hole; it needs to be the other way around.
@thintruman81846 жыл бұрын
I bought one of these valve assemblies recently and being curious, I decided to take a peek inside. To reiterate, yes the diagram does have the hole insert with the little retained pin, so for this type, it should be in there! I’m here because I hadn’t noted the position of the pin when I took it apart - doh!! (Twelve o’clock position) 👍Thank you MrCrass36 for posting this video.
@rhiannonjames52635 жыл бұрын
GREAT
@cn818212 жыл бұрын
👍👍👍🙏🙏🙏❤️❤️❤️
@sebanwo39 жыл бұрын
mine dsnt stop water. i checked all from video any ideas?
@sebanwo39 жыл бұрын
for all who is having this problem... pls do clean blue part from inside (scale) has to be very clean -thread
@alexmacdiver4 ай бұрын
*.*.*.* 2024 .*.*.* Torbeck Inlets Rabbit hole today. Water wouldn't completely shut off after filling. Original float was sealed unit, and had water inside. New kit from Screwfix had open ended float/cup. (Couldn't wait for postage of parts £12) Also changed rubber diaphragm while open. Sharp pin-type mount. Seating the white cup before sliding blue slip flange over ensures lug is in.