Please do a video on "removing grease from the carpet"...

90% of comments: grease all over the living room carpet 10% of comments: nice tutorial

Next video he will repack wheel bearings on the fresh bed linen

Many thanks for this video. My torque wrench was about to be scrapped as I could hang off it without it clicking. Your help, twenty minutes and a little grease and it's working again 🙂.

A big thank you for sharing this video. I was about to through out my proto wrench. I watched this video and repaired my torque wrench.

Your video has possibly saved my life man

I needed to disassemble the torque wrench to see why locking mechanism doesn't turn all the way, this video helped me a lot. Thank you!

Certainly you are a Bob Ross of torque wrench. Thanks for the show.

Once you take one apart, you should check the calibration on it. It should click within 15% -/+ of what you have it set for. Always take the wrench back to zero after use to remove tension on the spring.

Your wife must love you tearing that greasy torque wrench apart on the living room carpet.

This video makes me feel a lot better about the cheapo great neck torque wrench that I just took apart and serviced, the guts on the inside are exactly the same as what Tekton uses on their torque wrenches.

You’re a real one. Thanks for taking the time to make this bud.

You rock. I was so overwhelmed by this tool. Don't understand it really, but I can fix it, so thanks.

I keep my Gearwrench torque in my garage and probably because is not heated the grease got thicker and I couldn’t here it clicking so I took my wife’s hair dryer and set it up on low high for a good 15 minutes and it worked!!!

Thanks a lot. Your video help me to fix my torque wrench. Nice clear instruction.

Thanks, this really helped with my uncooperative torque wrench.

Thank you sir. I had a newer inch torque wrench that stopped clicking. Thanks to you, I was able to fix it and not have to buy another one.

I have the shorter version of this TW and you helped me repair and calibrate it. Thanks. Note to future self "Don't bang on TW with a hammer in frustration trying to break loose a nut"

Clearly, this is what I need to do. Thanks for the video.

Thanks for the video. You saved my torque wrench! My wrench wouldn’t click. I thought it was broken. Had no idea you could service these things. Why would you disassemble this on a rug?

Outstanding video bud! Thanks for helping me fix my wrench! I had made the mistake of storing my wrench all the way down below zero and that locking pin popped out.

Thx for all the details great video and very explained

Great video, I also suggest a very small amount of blue threadlocker on the final hex set bolt threads.

Excelente descripción y video, me sirvió mucho. Gracias Thanks

Amazing video! Thank you!!!

Excellent video...Well explained!

Subscribed. Very nice and informative. Thanks!

Your wife probably loved how you were working with grease on the carpet lol thanks for a video I learned a few things 👍

Thanks! It worked for me!

Thank you! My wrench was stuck. Only took under 10 minutes to fix. Just wonder how much the specs are off at this point. Prolly still close enough.

This came in handy, thanks

Thank you. Your video helped me fixing mine. I almost had it thrown away

Great Job

Thank you so much.

Thank you 😊

Thanks for this video. Now this has me wondering if THIS BAD GREASE thing might be one of the reason that so many of these lower priced ones, coming in from China, are having major problems with the "NO CLICK" issue. It's amazing how many reviews on so many makes and models have this problem of no click happening and people breaking bolts off and damaging stuff. I bought 2 of these last week. The smaller one was 1/4", Inch Pounds. It never clicked at all. I tried to test it on my vise, but due to no click, I wasn't sure how hard I should push it. I pushed it hard to see if that would free it up and the danged thing split the vise in half! It actually broke the entire base (white metal). I just returned both of them without testing the 3/8" one. THEN I checked reviews, something I should have done first as it turns out. I was shocked to see that more than 1/2 of the reviews.... in fact, the majority, were all complaining about the exact same thing! NO CLICK and the breaking of bolts. So, now I wonder if the problem might be that these cheap factories might be using bad grease or overly sticky grease that may be causing the problem. ORRRRR after seeing how JR inserted first the "click part", making sure that it was aligned with that front part where they meet to make the click, I then wonder now if perhaps THAT is the problem (or part of multiple problems) that from factory, the click roller thingy isn't even inserted properly. Let's just be honest here. One reason so many products from China are sub standard is the sheer lack of QUALITY CONTROL! In fact, on Amazon, there is what LOOKS like a really nice kit. What I like about it is that instead of shiny chrome, it's black with yellow letters and those guide things. It's also Tekton, but again, LOTS of the EXACT SAME BAD REVIEWS of NO CLICK. I'm tempted to order one and take it apart to see if it's an easy fix with totally cleaning out that grease and repacking with a lighter type of grease. hmmmmm

Show , gostei muito do vídeo , I lovy the video , I'm from Brasil .

Excelente video Desde Nicaragua

Thanks

Thanks mate!!

Thank you so much

Very nice video I didn't find like this in you tube, detailed. Because I lost the bottom portion I wonder the size of the thread so O can replace it. If any help I'll appreciated thank you anyway.

Gran trabajo

do i need to take off the top part just to unscrew the handle? I just want to take the handle of to grease the thread of it.

Great video! With my Tekton torque wrench, I've noticed that no matter how much I tighten the locking mechanism at the bottom of the handle, the handle still has a bit of play. I shouldn't move at all I don't think. Do you think if I tightened the hex screw on the locking mechanism, that will fix the issue?

my torque head is not totally straight with the body , can i adjust that with the allen screw on the side

Much appreciated, I took mine apart because of no clicks and it was missing the ball bearings on that last piece. Any idea what size ball bearings it uses?

Nice to see it was backed off after last use !!!

Suggestion to Call Team Torque for TW Parts and for torque wrench calibration

Thank you and Well done.............followed instruction but stll no click (torque setting).............so will strip it down and try again...............bye the way........do you know what the two pins in the threaded section, which screws into the handle twist grip do................mine are missing............Appreciated........Ron

Anyone know how to fix the black adjuster on the bottom mine is frozen? Autozone claims it has no warranty. I cant use it on low torque settings because the adjuster is too loose it only tightens and hols the torque I want on higher settings.

I have two Tekton torque wrenches that have this issue. I tried regreasing the larger one but still no dice. I submitted a warranty claim and they sent me two new wrenches, no questions asked.

How do you know if the preload to the spring is correct?

My torque wrench just does the opposite. It clicks easily at whatever torque I set (ex. I set it at 140lb to torque the tire of my truck just to test it and it would click without using much force.. I'm not that strong:)). Does it mean my torque wrench is broken, or there's still a way to fix it.. ? Appreciate it if I could have an answer.

So was it not working before and now you cleaned the clicking mechanism now it does work ?

Ok so where do the batteries go? Mine came with batteries and a tube of grease.. tekton 24335 right? Mine looks different though and says it has 3 vibration settings but i cant find the 1/2 inch adaptor that fits the head.. ya know, i wonder if my wife switched our gifts.. godamnit now im going to have to clean it before it starts to get crusty.. keeping this grease though, wonder where youd buy scented grease at? Never heard of Forher brand..

You know there is a point where you say to heck and just go buy a new one. That for me happened about the time you said one of these tools for the c-clip. Nicely done though.

Nice idea doing fiddly job over carpet, it'l stop small parts bouncing away like the do on my wife's lace tablecloth.

Gotta love the big WARNING sticker out disassembly and improper calibration around 9:44. Nice job, but how do you know it is calibrated?

Very informative video. I have a torque wrench where the locking nut is no longer loose and is extremely difficult to turn. Is it the hex screw that needs to be loosened? If so, does the wrench need to be re-calibrated? Thanks!

Just a little tip, though pliers are made to pull the other way.

Great Video - but now you have to calibrate it using that threaded collar at the end.

Someone please send him a parts mat. Great video though. Thanks.

Will the torque wrench need to be recalibrated afterwords since you are taking everything apart?

please show how to do calibration.

You must have StainMaster carpet...

My old torque wrench handle would turn while I tightened the bolt. How do I fix that. The new one does the same thing but not as bad. Example: I am set for 20 lbs as I tightened the bolt I noticed the handle was now on 40 lbs. This only happens on the low lb settings

Store it in minimum setting will destroy it. Already have 2 destroyed, that is stop clicking at lower settings. What happens at minimum setting is the adjustment nut in the handle locks up and clicking disappeared at low settings. Should store it with spring slightly compressed, YMMV. This applies for the Craftsman and Kobalt, not idea about Tektron, a different design. Had click styles and digital failed. I think beam and analog dial are more reliable. Maybe will tryout a split beam next, I hear its more reliable with 2% accuracy.

How about calibration

Will you need to recalibrate it afterwards?

When you put the Torque wrench away after using it and back the pressure off, the little lock knob at the bottom, should that be locked on or off?

I'm telling mom you got grease on the carpet!

Greasy tools on the carpet ..... its killin me !

Put a carboard or newspaper down to cover the nice clean rug next time, man. Also helps find parts easier if you dropped them.

Nice video, thanks! I bet your wife loved you doing greasy work on her carpet!!!

After that show next video calibration

I lost the pin 🤬 I messed around with my wrench for 2 hours, finally found this video and lost the pin. Curses!!!

Do you think a guy could avoid rebuilding these things if he were to pour a li'l air tool oil in the ratchet end once-in-a-while? Over his living room carpet, of course! ;)

Good video but I hope that's a carpet scrap or ur wife's going to cry or holler at you.

U sure u want tool Grease in your carpet?

Accuracy = Gone.

Floop

You didnt consider to take the measurement of the thread before disassembling the whole thing

Why did you do this on your carpet?

The laugh

You have schmutz in the plastic cover for the can of grease, the cover that it designed to keep schmutz out of the can of grease. Put the cover on the can, and schmutz can get into the grease. Not good! Clean the cover before you put it on the can! I bet you forgot to do that last time. Great explanation by the way, of disassembling and assembling a springy-dingy clicky-type of torquerizer. But use clean grease! How does one CALIBRATE this torquerizer thing, by the way? After you disassemble it and lube it up nice, you probably need to recalibraate it. And that threaded nipple at the handle end, that threads into something, and that the end cap thread over - how far in does one thread the nipple, before putting the end cap on? Or perhaps maybe it does not make a lot of difference, as long as it is threaded in far enough to have a good grip and not tear the threads and pull out when you thread the cap on?

That stupid autofocus is driving me mad

Sorry dude. couldn't get past the Channellock's and pipe wrench to service a torque wrench. You probably shouldn't be taking it apart.

Your video has possibly saved my life man