✨✨✨ Check out our other video HERE: kzfaq.info/get/bejne/m8x8ZqRlxJ65eoE.html

Tack welds on a butt joint = zero penetration. And then ground off completely flat. Lol the only thing holding that together is the black paint! 👍

Clever way of cutting metal to make bends, but if you want any strength in your welds, you need to grind a valley channel into the weld points. Then, with the welder, fill the valleys with weld, making sure the welder is set to proper amperage and voltage for gauge of metal you’re working with. What you’re doing is making superficial surface tack welds, then grinding them down, leaving behind next to nothing. These would be fine for cheap IKEA desks, but I wouldn’t use these for anything heavy! Still liking the video simply for showing the cutting techniques.

Love the way he always moves the ruler to measure 1.5cm instead of just putting a mark at 1.5 and 3 and 4.5cm lol

"a grinder and paint...makes me the welder i ain't"

Entertaining. It should come with a disclaimer that those spot welds on the tubes are not suitable for metalwork requiring strength due to low penetration.

To all the naysayers, use the geometric patterns and make the proper welds. I believe that’s the point of the video anyway…not how structurally sound the end product is. Personally I think the patterns used for the fabrication is awesome.

When you wanted welding lessons, but your parents got you a laptop and editing software.

I watch these videos to learn from both the video itself and also the many many comments. Always appreciate the useful stuff and also learn from the mistakes. Thanks to everyone both the video maker and the people who commented.

For the love of God JUST RUN A BEAD!! These spot welders will drive ya nuts!

What I do like is how accurate the cutting is with the grinder. No fluctuation of the marked line.

I've been in factory work for almost 30 years now and knew tons of welders, sheet metal, and machinists journeymen over the years while I was setting tools and dies. I should have taken welding up. I had plenty of guys that would have trained me and I love it.

Wonderful cutting, grinding and painting tutorial ✌️

The grinder covers up bad welds and the paint covers grinding marks

Wonderful grinding and painting tutorial!

So let's see: grind away the strength of my poor quality weld and throw some paint on it. Got it 👍

Great ideas for coat hangers, 👌 Thank you.

That's very smart. Thanks for the tips.

Very precise with that grinder.

I will still be doing it the boring way thanks!

Truly you are the best I have ever seen..I wish to learn

SHOW DE BOLA. PARABÉNS

I love when people square cut and surface weld, then grind off all of the reinforcement so it looks machine finished. Then act like that was all acceptable.

Some epic video editing and camera work here. This video must have taken many hours to make.

Not one pipe was hurt during the making of this video. Still nice to watch.

Maestro gracias por compartir saludos

I liked it, appreciate your skill, good work. thanks for your efforts.

When you want something that looks pretty in a short amount of time but don’t care if it breaks…

Fascinating art

Structural integrity has left the chat

thanks, you made my day sir

If you're going to grind down the welds at least weld it right. The way you are showing has no structural value. I fabricate rescue baskets and other load bearing devices and your welding would not pass weight testing and would be dangerous in certain applications.

This guy is much better at cutting metal than he is at welding it.

That welding is holding together nothing

Good luck getting those joints to pass any kind of certification!

looks good

I weld pipe all day long..everyday and my breaks off the trigger are shorter than this guy's welding runs.

Love the quality of your videos 😊

This is the basic bro equivalent of makeup/home deco videos.

I'm impressed not weding but grinding

Dude you’re NICE 👍🏽

My first job in sales took me to Hobart in London Ontario and when we were done business the guy offered to give me a try at arc welding in their classroom. There I am in my three piece business suit, put down my briefcase, don the visor and pick up a torch to lay a bead. It was wire fed. Later in life I would have liked my own oxy-acetylene setup because for what I wanted to fabricate it is more suitable.

I don't know the 1st thing about welding yet I enjoyed watching this..

Bravissimo!

Some serious grinding skills!

Очень красивая работа 👁👏

Looks visually impressive but I am not sure about the integrity of the welds

You can actually see the joint after grinding all those tack welds off it’s cool and all but kinda bad info for anyone watching this new to welding or looking to learn

Those welds aren't very strong

Interesting aesthetics.

Some cool project ideas here!

Guys, its the Editing. Im 95% Sure for that wall thickness the welds hold up like they should

Pleasant to watch esthetically speaking but from a mechanical point of view, there is no way this type of welding allows deep and strong fusion.

You are a god

If you're going to make those light tack welds, at least run a nice hot bead down the inside corner

"Grinder and paint makes me the welder ain't!" -A very wise man

Very impressive~!

Great job due!

Nicely done

Nicely work

I’m not a welder but is magic going to hold that tack welding together? Or is it video editing that will? I don’t think welding is boring. I don’t even find soldering wires boring. Even aluminum brazing is enjoyable.

What a great way to not weld.

How do you know what radius to cut?

Nice video editing! Could we see it without the dropped frames though?

After commenting and reading the comments which were critical on the strength of the weld after grinding off, I revisited the video and I found that there were sufficient gap in the joints for the tack welds to penetrate to give stronger joints than I thought; even if the joint is ground to the surface. Like me I invite others to relook at the video.

I am also interested in the kind of welding machine you use. It is very cool

Exelente video

Awsome..

Top demais 👏🏿🙏🏿👨🏿‍🏭🇧🇷

Nice work

Waiting for the pipe welds..

Nu!!!! Q talento!

Love this channel

Hey man this was a cool video with some great looking end results

Belo trabalho!

What kind (type, model) of welding machine is this?

Vidonun başında öğrendiklerimden sonra,örnek uzay gemisi bekliyordum.Sadece askı ve raf!.

That’s cute, apply the weld in spot welding method then grind it all off. Spot style mig has little penetration but it looks better on videos, also most arm chair experts struggle to do a continuous mig run. Just sayin!!!

Very accurate cuts and templates.

I don't know why I'm watching this 😂 but it's pretty impressive

dude, you make it seem so easy! thanks for the video!

very very good

Let this man build the roll cage for your Honda Civic!

Very nice 😊

What kind of welding is this mig or tig ?

Really nice work.What type of welding instrument is this?

Very nice work and videos

The fact that in the first minute they, instead of, I don't know, using a rule properly. They instead decided that the best way to measure out the distances correctly was to move the rule to the new marking instead of just marking the it using what's already on the rule baffles me...

He is the real IRON MAN!!!

Very talented person, I'd like you to teach me how to weld like you do.

I will do whatever I want and nothing and no one can stop me. Not even some clickbait title.

If the application is furniture of something like that, what's the problem with the welds? Appreciate the creativity this can stimulate in someone ambitious to try.

What paint you use?

Cool

Класс! Перед тем, как сваривать, края металла профильной трубы лучше забить молотком немного внутрь -при зачистке не будет сниматься большая часть сварного шва, так как он будет почти весь внутри. А так всё класс.

Zabardast

Entertaining

Thank you. That was so satisfying to look at your work. I appreciate for the ideas and inspiration.

Mom I wanted welding lessons…. We got welding lessons at home.

BERNER !!!! 💪💪💪💪💪