Episode 1 of the FTE swap in my Toyota Landcruiser HDJ80 1991 model. In this episode we give the new fte a bit of a birthday and begin to start the swap over. Stay tuned and make sure you subscribe for more.
Пікірлер: 37
@mountainconstructions6 жыл бұрын
You are one smart kid for a young fella You've taken on a big job and done/explained every step brilliantly. Wish i had the knowledge and confidence to do that level of mechanical work.
@brendonv1016 жыл бұрын
Hugh Jazz thanks mate. Means a lot. :)
@alians19786 жыл бұрын
Great job mate. Lot of those explanation went over my head though :)
@blairo157 жыл бұрын
Good to see you back on KZfaq. Great series. I've got an na 1hz.very interesting. I'd love that engine with an auto
@mjhmech4903 Жыл бұрын
Well done Brendon
@brendonv101 Жыл бұрын
Thanks mate.
@dahirabdisalam49586 жыл бұрын
Thank y for your clear explanation how you show us every step
@brooa7 жыл бұрын
nice work, cant wait to see the rest :)
@Nathan-fv8rt3 жыл бұрын
Sick tool shirt
@brendonv1013 жыл бұрын
Why thank you.
@arielgarcia99476 жыл бұрын
Nice work Brendon thanks for sharing it. I’m curios of how many MPG are you getting now.
@maporules7 жыл бұрын
yaya ill be waiting thanks mate
@garthdillon68197 жыл бұрын
love the video mate. just wondering why you went with the (fte) and not the (ft )
@brendonv1017 жыл бұрын
Garth Dillon more power and better fuel economy.
@random11101112 жыл бұрын
Was this because of the previous fuel pin modes? What were the results of that?
@J..O..D6 жыл бұрын
Very knowledgeable! What did you pay for the motor?
@kylewilson26744 жыл бұрын
Brendon, I've got a 97 US fzj80 that I'm looking to convert to a 1hd-fte with an a750f. What's the biggest hurdle you see there? I know it's been done quite a bit but just want to know if wiring is going to be my biggest issue. Thanks!
@brendonv1014 жыл бұрын
Yeah wiring and fuel system changing over to diesel. You'll need a diesel pickup in tank and most likely bigger lines. Diesel requires 12mm feed.
@mikedavies82836 жыл бұрын
Hi, Great video series, really helpful. I'm seriously considering replacing the 1hdt in my 80 series with a 1hdfte also. I have the A442F transmission which is an auto not a manual. Do you know if the 1hdfte will mate fine with the A442F. I'm hoping the answer is yes. Also the 1hdfte sump looks to be a bit different. Does this cause any problems with the 80 series cross member?
@brendonv1016 жыл бұрын
Hey mate, yes the A442f trans will bolt up to the fte. All 1hz/hdt/ft and fte share the same block so the bolt up is the same. Just use whatever came from the 80 so shifter location is the same. As for the sump, if you use an fte from a hdj100 they have a different sump due to being ifs. In this case the sump and pickup needs swapping from your 1hdt. If you use a hdj78 or 79 series fte then the sump is all fine for the live axle 80.
@mikedavies82836 жыл бұрын
Thanks for your help, much appreciated. I have been told by a mechanic that if I use my A442F trans with the 1HD-FTE the ECU does not like A442F and will probably make the engine go into “limp mode”. Apparently, because the A442F is an older transmission its electronics struggle to talk with the 1HD-FTE’s more advanced ECU? Any clarity would be helpful. The 1HD-FTE is from a 100 series. Cheers
@brendonv1016 жыл бұрын
Mike Davies wholesale automatics sell a standalone ecu for the trans.
@maporules7 жыл бұрын
Hell yeah! how long untill next ep?
@brendonv1017 жыл бұрын
Danslife maybe tonight mate. ;)
@b_gonzz5 жыл бұрын
Could you do this conversion for me? Haha
@keyzerdos1347 жыл бұрын
You're supposed to do the valve clearances when the motors warm, reason being that metal expands under heat, especially operating temps. That's why they were 'out'
@brendonv1017 жыл бұрын
Sean Keyzer incorrect. Read the manual mate.
@keyzerdos1347 жыл бұрын
brendonv101 lol good luck with it mate 🤞
@brendonv1017 жыл бұрын
Pretend mechanics -_-
@keyzerdos1347 жыл бұрын
I'm not a mechanic, but I've built my fair share of engines.. I also have half a dozen friends/relatives who are mechanics, who have ALWAYS mentioned doing valve clearances when warm. It makes sense if you can comprehend what happens to the materials involved when they're subject to heat.
@brendonv1017 жыл бұрын
Sean Keyzer well lucky for you mate I'm a diesel mechanic so I can tell you the facts. Every engine manufacturer is diffeeent. Toyota list the clearances done cold so like a said, go download the 1hdfte manual and see for yourself before telling me how to do things.