You welcome

You welcome like, share, and subscribe is big help me ok thanks

Thanks don't forget to help me subscribe, like, and share.

You welcome buddy

you welcome

@@alltsab sir maybe you can help me out my 5speed manual seems like my gears cut to short like in first gear it only goes up to 10 miles per hour is it anything i can be a wear off or i can look out thanks

Not many people want to share

@kirtadams439 thank you 😊

Uwelcome

You welcome

You welcome help me subscribe ok brother

why does it lock and unlock when you use compressed air to blow in it ?

@@dsa420meh7 because there's a diaphragm that operates it, so if u put pressure to one side it will push it and thr same of u put pressure to the other side, but when working in the truck it's vaccume pulling on the diaphragm

Thank you for adding that I've been spending hours on the internet with the question is my 2016 vacuum or not you just answered it

You welcome

Test your solenoid to see it working

Im not sure but maybe your solenoid slow response that all.

Zoo siab pab tau koj me me thiab os

I never reset so I don't know

I don't have so everything through here and thank for future feedback

If your 4runner have engine light use obd2 to scan for code to fix it. It's sound like bad transmission but not sure why when you put in 4wd it can move but not 2wd. First thing is scan for code then fix the code problem. Can not be blindfold to fix car doesn't work that way always scan for code to do troubleshooting ok.

I don't have auto shop brother

I'm not sure but check your sensor on low drive because the way you mentioned no light on low gear. If sensor doesn't work it won't engaged. If you have a friend have the same tundra swap his sensor to your to see it work ok. Please help subscribe thanks

How do you swamp out that senor

@@alltsab where is that sensor located

Wow all I have to say is check your sensor and used obd2 to scan to see what code pop up

@@alltsab thanks. will do.

@@lowellguzman7249 don't forget to help me subscribe so we can stay connected for future support ok

Take out your sensor it has the number on it

Unwelcome

Need help with my 91

Yes can you follow my video it will help you to diagnose your situation. If not message here I will help you. Please don't forget to help subscribe to my channel. Thanks

Replace only one

@@alltsab thanks for getting back to me so soon. The brown solenoide is not working when I apply 12v but I get suction on the nipple..does that sound right? Will the light come on if the solenoid is not working?

All Tsab thank you! I replaced the brown solenoid and now my son has 4 x 4 Thanks again!

You can order from toyota or look online like eBay they might have used one

If your solenoid doesn't pump air then you have to replace it. Blowing air to it just to test to see the fork actually moving to engage or not only.

Thanks! My 1995 T100 has same symptoms.

Hi, you, did you solve your problem? I have de same problem on my 4runner 96 4WD limited . Moves in 4L and 4H but when i put it back in neutral, the lights ATP comes on into the cluster and wont move in 2WD!

@leon angel no.. I did found the problem.. My vacuum line is broken on the rear actuator 4x4

Thanks men! Im goint to check it tomorrow! I hope it's the same and solve the problem.

@@mashumineithor your welcome 🤙

Possible your add still engage

I have this problem, what was your fix?

@@TheTrev4477 Replace the front differential actuator, maybe it could be more engine brushes but I preferred to buy a used one

Thank buddy

You welcome I don't have a store

You can remove your from the truck and get the part number from it

1999 4runner manual transmission ..

Not sure but I think under 2000 i don't see 01 and up doesn't have it. Maybe the limited may not have it so I'm not 100 percent sure.

@@alltsab thanks,my 07 tocoma goes into 4 wheel drive but to take it out I have to shut the truck off turn the switch off then when I turn it back on it disengages. Anything you can think I should check?

My friend thank you for watching my video. I don't have any diagrams show you how it go or connected. According to this video it's very much explained almost everything already. I also don't have this truck so I can not do a video to show you. It's sound like your truck have been modified so it will be different and difficult to figure out. I wish I live near you so I can come to help you fix it however I wish you the best and if you have questions don't forget me. Please help me subscribe to my channel so future video you can see it right away ok. Thanks and God bless you

@@alltsab just one more question sir does engaging and dis engaging the 4WD has anything to do with 4wd indecator lamp or sensor missing ? Or its just the brown and blue solenoids that controls the engaging ?

@@alltsab if it is possible you can show where is the vaccum location that comes from engine to do the engagment

@@feraskassem9199 the vacuum lines is from the 2 solenoid to the differential only. I don't have the truck so I can really give you many details.

Check the light in your dash maybe it burn out

@@alltsab how can i check that!? Do i need to open de dash??

@@360ikki yes take the cluster out

Thanks so much i will try to take out

Hi bro, i check the 4wd on the bech but the front diff is not working, can you help me telling me wich kind of air you suply please?

Scan to see what type of code you have.