Toyota CV Axle Dissambley & Reassemble

Рет қаралды 64,943

4 жыл бұрын

video tutorial on how to disassemble a Toyota CV axle and replace the torn boots also inspect the bearings
GET THE TOYOTA BOOT KIT FROM THE VIDEO HERE ( AMAZON ) ( LEFT FRONT AXLE)
amzn.to/3SKWgkQ
GET SOME CV AXLE PLIERS / TOOL HERE ( AMAZON )
amzn.to/3NSs863
NOTE: IT SAYS ON AMAZON COMMENTS THAT BUYING ADDITONAL KITS CAN BE USED FOR OTHER SIDES AXEL

Пікірлер: 42

@GEARMOAUTO Жыл бұрын

GET THE TOYOTA BOOT KIT FROM THE VIDEO HERE ( AMAZON ) ( LEFT FRONT AXLE) amzn.to/3SKWgkQ NOTE: IT SAYS ON AMAZON COMMENTS THAT BUYING ADDITONAL KITS CAN BE USED FOR OTHER SIDES AXEL

@BradThePitts Жыл бұрын

Fantastic. There's a lot of helpful videos about removing the CV axle, and I needed this one to know how to replace the boots.

@armchairtin-kicker503 Жыл бұрын

Notwithstanding all the other vodcast on this subject, it was helpful to see what comes inside of a Toyota OEM CV boot kit; thanks for the unboxing.

@k-art-L 3 жыл бұрын

This video is so helpful!! Thank you!!

@alale923 3 жыл бұрын

Really a great video. Thanks man.

@richj2709 4 жыл бұрын

Informative video thanks!

@Alrukitaf 5 ай бұрын

Great info. Tripods are good to prevent motion sickness when watching though. Great little investment to improve watchability.

@foxgrove60 Жыл бұрын

Good video not a bunch of jaw jacking showman bs really good info works for me time saver

@lonesomecricket7721 2 жыл бұрын

Thank you for the video. 👋🏻

@ektj Жыл бұрын

Awesome. Very helpful

@andrewawp 2 жыл бұрын

This will help out a lot. I have been stubbornly trying to cut the outer boot off with hack saw blades because its ripped, and was low of grease and making noise. I bought the whole boot kit because it was actually cheaper then a single outer one, but I am wondering how to slip or cut the boot to go over the outer bearings. Better to just take the whole thing out and check and replace both.

@paulmares8836 3 ай бұрын

I appreciate that I was changing my lower control arm and my CV axle slipped off and I didn't know if I put the CV axle back in wrong because I'm getting like a little knock now so I'm assuming I need to pull it out and reset it or do you have any idea

@nemangrad 2 жыл бұрын

Good job!!!

@alale923 3 жыл бұрын

Besides the metal case how do you tell if an axle is an oem toyota axle?

@mullerandre95 3 жыл бұрын

Most of the Corolla joints I've done the outer cv is on there tight. Then I just take the inner off and slide the boot over from the inner side. Some Opel joints have a snap ring(circlip) holding the cv in place on the shaft. Great vid!

@pixel6878 2 жыл бұрын

Is the inner easier to take off the joint? I'm doing this on my 09 Tacoma and the shop is having a hard time getting the outer joint off, and no shops around me have a press to press it out.

@mullerandre95 2 жыл бұрын

@@pixel6878 much easier, the outer joints tend to be stuck on so bad that you have to cut them up and break them apart to remove them. Just remove the snap ring on the inner cv slide ir off, remove the boots and put the new boots back on. Reassemble and refit should be about 30 mins per side. The Tacoma should have a snap ring on the cup sitting in the diff housing that you can pry out with a screwdriver to remove the shaft. It's an messy job so either wear gloves or be prepared to scrub your hands well afterwards.

@nemangrad 2 жыл бұрын

For the Toyota Sienna 2019 xle will be the same. I don't think anything has changed there. I will change the anther. Thanks for the video!

@MrMalzers 2 жыл бұрын

Awesome thanks

@ro-landocalrissian4633 Жыл бұрын

Hi 👋 I’m curious, will the Toyota dealer sell these rebuild kits? If not, where would you recommend I get one & what brand? I have an 03 Corolla & always took care of it. It’s not making any noise but the Toyota mechanic said right away that I have to replace both axles! Which is expensive! I saw it on the lift. It was leaking some grease on the axle bar on both. The car has 150,000 miles. He said one of the axles is not made any more & advised to get an aftermarket one. Should I do this or try and repair it? Any advice is appreciated, thanks 🙏

@insaynbcr 3 жыл бұрын

What gen Tacoma were these from?

@theylied1776 2 жыл бұрын

I don't know what model this CV joint came off of... but the OEM Toyota drivers side CV joint for my car cost about $600. I'm going to order one of these kits and rebuild it myself.

@frojooro4812 Жыл бұрын

What is the 2nd set of crimping pliers called?

@scottthomas1810 5 ай бұрын

for future reference.. earless cv boot clamp pliers. One example is Lisle 30500 pliers.

@fks-pv8il Жыл бұрын

What holds the inner axel cv joint together?

@JohnMarshton777 10 ай бұрын

Tension mainly. Plus the clamped boot technically. Once installed in the car, the bearings and the cup cannot separate because it's held in by the trans and the hub. At least to my understanding.

@Cornfed_Off-road 7 ай бұрын

What year Toyota?

@walter.bellini Жыл бұрын

Thank you for the video, enjoyed it Here is another video that explains it as well, but didn't pull the CV joint out of the transmission to save a lot of headaches kzfaq.info/get/bejne/j65ldslo2rC6ZY0.html

@arturohernandez2313 11 ай бұрын

Considering the cost of new cv axles being relatively cheap for older Camrys it’s just better to remove and replace than to do all this since you are already having to remove the old cv axle do this anyways.

@brett9382 11 ай бұрын

Toyota cv axles are significantly stronger than replacements. Not a big deal for camrys but a definite for toyotas 4x4s.

@JohnMarshton777 10 ай бұрын

I'll appreciate this in my lowered corolla. Dirt roads aren't kind to the axle boots. But they have like. 20k miles on them. Bearings are probably just fine. Pluuuus I'm pulling the trans anyways soooo. Keeping costs down is key 😂

@wesraffa 4 ай бұрын

Most oem axles last 20-30 years longer than the junky replacements they sell. If the joint is in good shape definitely reuse it

@jerrypollak7651 Ай бұрын

🫵🏼👍🏼

@davidsexton4033 Жыл бұрын

this is a reboot, not a rebuild nor a disassembly

@tonykillingsworth9247 7 ай бұрын

No !!! You did half a job .Always remove all the grease ...fully disassemble. Inspect for wear then put it back together

@peterp4753 2 жыл бұрын

Your video is useless ! You skip the last part, how did you slide that axle inside that cup ?

@GEARMOAUTO 2 жыл бұрын

Make a better one then. I can't hold your hand on every little part

@peterp4753 2 жыл бұрын

@@GEARMOAUTO Little part ? That's the biggest part !! Looks like you couldn't slide the axle in that cup yourself, so you just skipped it, and showed it reassembled, or swapped it with different axle. Ridiculous !

@GEARMOAUTO 2 жыл бұрын

Aight aight, to put the two together fold in the 3 bearings on the axel and slide them into the tracks on the cup. It can be a little stubborn but they do go in. I edited past it to save time but that is basically how I did it.

@peterp4753 2 жыл бұрын

@@GEARMOAUTO Show me, don't tell me. I tried for 2 hours and I couldn't do it.

@aaron108 2 жыл бұрын

@@peterp4753 Dealer I'm at will charge like 400 an axle, so pay be $399 and i'll show you

@GEARMOAUTO 2 жыл бұрын

Any support Appreciated. Small donations help the channel grow. Paypal.me/GearmoAuto VENMO- @Gearmo-Auto CASH APP - $GearmoAuto CRYPTO- 34d49fai2nN4LzACynSjRhnbmugP6AuExD I would love to make more content with better quality to help everyone save money and time. Thank you!