Just did the same repair on my 2008 Lexus RX400H. Basically be the same repair with all Toyota/Lexus hybrids with electronic ABS braking. Important things noted not mentioned in this video, common sense you DO have to bleed all brake lines after the re-installation to remove any air pockets in the brake system once you disconnect and open the brake lines from ABS pump. If you don't, you will have air pockets in your system that will affect your braking performance (ask any mechanic). Besides it is routine maintenance to flush your entire brake system if you haven't done yet. You don't have to disconnect the battery but remove the 2 ABS relays to cut power to ABS pump during removal and installation. Highly recommend flushing out all the old brake fluid with Dot 3 or 4 by disconnecting the brake fluid reservoir hose to ABS pump and drain then extract remaining brake fluid in reservoir with turkey baster or multi-use pump as i did. After installing the replacement ABS pump, you will set off codes, multiple blinking warning lights, and long warning tone. Sound will go away after couple seconds until you turn off and on the car again. When you bleed the brake system (two person job) car completely off, reinstall relays and turn car power on but don't start, then put computer in diagnostic mode by installing a wire jumper between pins 13 and 4 on OBD2 port connector under drivers dash. For rear brakes (no need to jack car up or remove tires) one person gently pump brake pedal twice and hold, other person releases furthest bleed screw on driver rear caliper until all air and old fluid extracted then tighten (you will hear loud chatter which is ABS continuously pumping fluid out). Refill brake reservoir and repeat rear passenger side caliper. For both front brakes (turn wheels to side bleeding for easier access, again no jacking car or removing wheels) bleed old school way by pumping 4-5 times and hold then open bleed screw to force air bubbles and old fluid then tighten bleed screw and release brake pedal. Repeat til all air and old fluid extracted while always checking the reservoir and topping off with new brake fluid. No scanner needed to reset codes. While still in diagnostic mode simply pump brake 8 or more times within 5 seconds. Turn off car completely and remove jumper wire from OBD port. If you still can't clear the codes then you will need an OBD2 code reader with ABS feature for ASIAN vehicles. Finished..... ONE MORE THING!! As mentioned in this video. The recall regarding Toyota/Lexus brake actuator assembly issues is "WARRANTY ENHANCEMENT PROGRAM - ZG1". Original recall was 3yrs/36k mi, but so many customer complaints that Toyota extended to 10 years from date of purchase or 150k mi which ever come first. Dealer won't ever mention this recall unless you bring it up as this is a "Warranty Enhancement Program". my vehicle was over 150k by 600mi and Toyota refused to honor the recall!

I can't believe I found this video. I was even unable to search for this problem properly. But thanks alot to tell the exact solution. I'm gonna fix my car now. 🎉🎉🎉

I think the video was great. My light just came on and you have confirmed the problem. I was kind of expecting the ABS unit to go out and it seems it finally did. Great job!

Thank you SO much for posting this! You hit right on the issue I’m having with my Hybrid Highlander & now I know exactly what to do to fix it. Much appreciation to for taking the time to share!

Thank you so much mine is Toyota Camry Hybrid. But the trick is that this problem comes and goes. Especially winter months. It's gets dangerous because if you're not aware you could rear-end motorists I hope this part is the same problem I got. Thanks alot brother

Been hunting this down for a month.. great info and thanks a million

Great video! So cool how you did this yourself, both troubleshooting, and purchasing/installing the part.

Thanks for the video sir, and no apologies for your 'weird accent', you know at least one more language than most people watching this, including myself

I have been looking for a while why my camry has been making that noise. FINALLY!!! Thank you so much

Thank you very much! My warning lights came on not to long ago. I will update everyone as soon as I get it fixed as far as the prices and the procedure.

Thank you. I'm hearing a funny electrical noise and a funny whining or whirling noise also and this video helped pinpoint the problem.

You did help me to find out what the problem with Prius as well. Now I can fix my problem also. Thank you.

Glad I found this. My 2008 has the same issue AND a really loud siren coming from the dash. I hope the annoying siren is part of the same issue.

Good evening Sir, I really appreciate this information, very helpful. Keep up the good work !!

This is the exact car (same color too - mine is a 2009) and same problem I have with my car. Thanks for the video! I couldn’t find anything else to figure out what it was. I don’t have any noise with my ABS/VSC lights on.

This is very helpful thank you my light just came up yesterday so I know the next step thanks 🙏

Hey great vid, I have a 2006 hybrid highlander and now an alarm turns on if you drive the car so it’s letting you know you shouldn’t drive the car, I’m thinking the reason for that is because the vsc check warning has been on for more than 4 months, I was thinking on getting the abs module and replacing it myself, do you think it’s gonna fix the warning just by changing it? Thanks

Thank so much, this video is an eye opener that I think is going to give solution to the problem at hands thanks.

Hey bro. Is it still running good? Btw best info. My friend car has same issue (apperantly). Will help her to replace the part . Did u find it doable stuff by person with average tech still? Do reply. Thx alot

Just bought a 2007 Toyota Camry hybrid from friend and love to know more of your videos to learn more of this type car. Anyways thanks for the first video really helpfull to me that I don't offer the dealers deal

THANK YOU! I hear the same sound when my foot is pressed all the way down on the brake, moving or not. I have not wartning lights yet. Can you tell me where you got the replacement unit? I the unit still working? Thanks

Very Helpful,thanks

hi i have 2009 camry hybrid and have same problem you described in your video. Module only cost in new york $400. where did you get your part for 200 bucks. please let me know

Hey thank you for the video i have a similar 2008 Camry and it has the same issue it’s not only showing the lights on the dash but making a loud sound when i am driving

my 09 hybrid got the Check VSC System warning after replacing the front rotors... i pump not making any noise... could it be i broke the ABS sensors or i need to rebleed the system? any advice ? Thanks in advance

Dude you just saved my life, thanks amigo👍

Thanks your video helped me figure out the issue on my 2009.

Thanks buddy noticing same issue right now with mine. Will have to get the oart first

my car still no warning light but it have same problem like should i check the abs?

Hi! Love the video! What is the name of the part so I can buy it by myself!? Thanks

What codes came up when you checked it with your computer?

Having this same issue what's the name of the part?

Hi friend I seen you videos on youtub I love it . Bat i have problems with my 2007 camrey hybrid they dishwashers under screen some warning light and check hybrid system?????🤔

Thank you. This helps

I just found this video, I know I’m 3 years late.. the second noise you showed, THAT’ MY NOISE!! I haven’t been able to explain to anyone that noise. I have the first noise, the normal noise, but it last me a while longer.. and I have that second noise, exactly.. I have no VSC warning message though, and none of my lights stay on like that.. my mechanic told me that there are two brake control modules that are going bad, it’s costing me about $2400 to get it fixed.. does all that seem right? With the way it brakes and the noises I get I should have some kind of warning messages or lights.. thank you..

Thanks for the great info! My 08 Camry Hybrid had exactly the same symptoms. I bought a used one from ebay, but having trouble finding a mechanic that will respond to my request to put it in. Do you think it is possible to do it myself? From you description, it seems there are no special procedures or tools needed (other than to reset the warning lights).

Straight to the point and accurate

Where did you find your replacement for abs

Did the triangle warning clear when you did your repair? Thanks for the video, by the way.

When you replace the abs actuator is not necessary bleed the lines right

Hello ,Can you please tell me the name of the part am having the same problem on my car and thank you for your video it was very helpful

thank for your help do you have any idea about fuel pressure valve in a 2008 camry

I have a 2007 2.4 le Toyota Camry im wondering do you having to reset the code with a scanner tool or can you just put on the part and drive it?

Thanks for the video

does a 2012 toyota camry hyrbid LE even have an abs system, it just shows sensors and a youtube video showed me that if when searching for abs parts only sensors come up then its a problem with the sensors or parts in the breaks. I'm buying a better diagnosis tool because the one I have is not picking up the ABS error. Hope this helps someone else out there.

What's the name of the part you changed?

Hi Kenny. I’m looking to buy a 2006 Highlander, but it’s making the first noise you demonstrated. There are no indicator lights on and the ABS works just fine. You said that noise indicates that it’s working properly ... does it always make that noise? It’s making it intermittently, even when the car is off. Toyota dealership said that isn’t normal but they didn’t know what it was. They said it could’ve been a recall but it expired in 2016. Please let me know if that noise is normal when car is off and how long it lasts. Thanks!

I have a 09 Nissan Altima hybrid and I’m having the same noises I bought an ABS pump from the junkyard changed it and it’s still making the same noise what should I do from there please help

Thank you soo much for this videi

Well, the abs module in my 07 hybrid Camry makes a "Healthy" noise, yet my dashboard is displaying the "Check the VSC System" error. What should I do?

where did you get the part, I also have a 2007 camry hybrid exact problem

looking for this part for my 06 highlander hybrid. Cheapest i found used at a junk yard was $700, cheapest new one i found was $1152. I am not sure if I can afford to put this part in. It costs about half the vehicle's price if I get it done at a toyota dealership. Hopefully a junkyard will have it cheaper eventually. Driving the vehicle just gives me spongy braking. The braking power is still very strong.

I thought we had the same problem with the ABS pump, because all those lights came on, and we got diagnostic codes C0215, C1241, C1252, C1256, C1343. Turns out it was just a leaky brake line on the rear drivers side wheel. It was a simple fix and all lights and warnings went away. Was ready to get a replacement ABS pump ($$$), but that definitely was not needed.

How you doing Bro, I have exactly the same trouble with my Camry, so I'm wondering where did you ordered the part for it, so I can order mine I really appreciate that info! Thank you very much for your video I founded really useful 👍

Hello. I change the ASB module but my lights still on. Is yours or am i missing a step?

Nice video. Question did your mechanic bleed the air out of the abs module or did it bleed itself?

How Often the pump should turn on if its working fine? Mine turning on every 10 seconds, even when parked and I'm not braking, there is no error codes or lights on dash, but I don't think pump should work every 10 seconds..

Very nice job

Hey, did u have a long beeping sound also?

Hi I have 2010 Prius that makes the exact same noise when I step on the brake and the shop I went to told me there’s no error code yet and I could still drive it but eventually I should replace “Brake booster hydraulic system” for about $1,500. That was like 6 months ago and it’s starting to get worse so I want to take care of it finally. So is this the same thing as what you got? Or what I need is ABS accumulator instead of Brake booster hydraulic system ?

Gracias

Help do you know the part number for that part and the exact name? Is it the whole abs module or part of it?

Where did you purchase abs

Por que mi Toyota camry 2007 iba corriendo bien y comencé ha sentir que perdía velocidad pose el acelerador y no subía me estacione lo apagué y lo volví ha encender y prendió y arranco bien pero en 5 minutos se apago de ir corriendo lo pagaré nuevamente y la primera vez no entendió y en el segundo intento si ojalá pudiera contestarme

Where can I find one of these?

Hello, mine is giving the same problem which you explained in youtube. Please, could you assist me to get a replacement of my ABS system just to alleviate my problem?

My car the seem problem can you help me

I got this error message after dumping a crap load of money on everything the internet told me, it ended up being the catalytic converter. Not even Toyota mechanics could figure it out. A mechanic from Tijuana MX lived close by and figured it out in less than a minute. Toyota service dept told me I needed a new engine and quoted me $6500.

Hi where did u find that part.my hybrid Makin a beeping noise wen I press the brakes

I own a 2008 Toyota Camry and I already replaced the hybrid battery but the light of check hybrid system is still on Car runs well Can you make a video to reset the light Thanks

It's me again. Maybe I missed it in the video, but did you have to go to the dealer to "reprogram" the system? Did the Check VCS System light go off on its own or did you have to clear the warning? Thanks again.

Where you bought this ABS monitor??

Thanks for the video. I have a 2007 Camry hybrid. The VSC light comes up. I tried resetting but, keeps coming back. The ABS module does not make the bad sound, just the clicks. Any other thoughts?

Can you fix Apc

Your car is hybrid? I have the same problem with my Toyota camry hybrid 2009

whats up with the volume on this

your good ...yes my 2006 toyota highlander hybrid vsc system check same problem and noise also...i need to fix....give me some idea..i like to do my self..Thanks

Which junkyard did you get the part that cheap?

Same for 2006 Highlander hybrid This May also help reset codes without scanner. ------------------------------------------------------------------------- Check VSC system warning: Scangauge cannot read these error codes, nor reset this light. It would appear that regen braking, traction control, and posibly some anti rollover control is dissabled if this warning light is on. So it is both fuel inneficient and possibly dangerous to drive with this light on. First find the obd computer plug, under the dash, near your left knee, where your scanguage plugs in. Turn car OFF. Use a paper clip or wire to jump TC to CG. TC is on the top shorter row, 4th pin starting from left CG is bottom longer row, 5th pin starting from left See diagram: __/_@_@_@_TC_@_@_@_@_\ _/__@_@_@_@_CG_@_@_@__\ Note: I saw some posts when researcing this suggesting a jump between TS and CG. (TS is just to the left of TC ie 3rd pin). While this may/may not work on some Toyotas. On the HIHI this doesn't seem to do anything other than cause a Hybrid System Warning to be thrown. So don't. Once the jumper is in place, To read your VSC error codes: Turn car to ON, you should see the message "VSC DIAG".It will read "VSC DIAG OK" if there are no codes. Brake warning lights will go off for 4s, then start to flash. Count the flashes, these are the error codes that caused the light to come on. They may be real, and something may need to be fixed. If the car really is broken, just resetting the light won’t do much, as it will soon trip again. If the brake lights continually flash, then there are no codes and the display should read: "VSC DIAG OK" Once the jumper is in place, To reset you VSC error codes and lights: turn car on. Press the bakes (enough to make the tail lights come on, not all they way) and release 8 times. Once you have done it enough times the display will change to "VSC DIAG OK" Remember to remove jumper wire when done. You must complete the 8 presses within 5 seconds Credit to -JSTCD @ Toyota Nation

Husband replaced this part and he said the sound is gone but the brake performance is really bad now to the point where he doesn't want to drive it and all the lights are still on...... help?

You're supposed to bleed the air out of the brake lines when you replace the hydraulic unit

Doesn’t need reprogramming after installing the new one?

Did you need to bleed the brakes or you just replaced the actuator ?.

Im getting only the first noise… 2007 camry hybrid… how to fix it ?

How Dangerous is it to be driving with this problem mine just showed up two days ago, It be okay to keep driving it for a few days till the part comes?

Hi there . What is the parts name?

I have the same problem. Do u know where to get for toyota estima 2008?

Thanks thanks thanks!!!!!!!!!!!!!!!

Hello friend. This is hybrid model?

Can u send the link for buying the accumulator??

what is the new part name

Do you have link where i can buy this thing..i mean the junk yard?

Great information,but after two days the whistle sound continues without stopping I rescan the no error code what should I do in this case?

My vsc light was a cable coming from the wheel bearing.

Has anyone had any luck buying a new ABS actuator? Or how to determine if a used one is in good condition?

It’s so hard to find the 2nd hand part that works. It’s like $500 here . But new one would be $1,200

yes it is

1k too much it’s definitely a simple fix you can do yourself!! Y’all crazy af

Just happened to me.........scanned the computer, got "low accumulator pressure" code, etc etc........Ordered a Used accumulator on Ebay, that cost like $450 with shipping.......then ordered the Tech Stream laptop from ebay, that was ANOTHER $500........I wanted the software so I can erase codes and Flush the brakes(since this is done electronically).....I hear of people "just" swapping ABS units and it's fine.......but I wanna be able to program and do everything just incase.

this can be wheel bearing worn out, also nothing to do with that abs module, ur mechanic must totally love you since he left air in ur brake lines😀