This what all automotive videos should be like to the point and informative very well done

gracias por tus veritables consejor¡s y por compartir tus metodos, te sigo desde hace tiempo y me gusta tus profesionales metodos de diagnostico, many thanks

Thanks. My MK2 TT is due to the 40A fuse at the back(above batter)fractured hence the code contains "intermittent " after the 01276 error

Grateful to provide this beneficial information to us. It's wonderful your Intellectual skills.

I have used you in the past for a abs pump on a corsa with no flow to one of the outlets. Very quick turnaround service. Thank you

If you have Mazda 3, there is a valve that gets stuck WITHOUT an error code. The brakes will feel mushy. You need to get on an unpaved road and brake hard activating ABS 5-10 times. This will unblock the valve. No diagnostics or replacement needed. You are welcome.

I have an old abs unit from a suzuki that u would like to experiment with. Any knows what voltage goes to the solenoids?

I checked the 40 amp fuse for the abs motor and the fuse is good but there’s only 4.5 volts there. Any idea what could a use that?

*I have a 2004 Lexus GS300 with the fault codes of C0246 open/short circuit SRR brake booster, C0256 O/S circuit SRL, C1223 Malfunction ABS control module. All wheel speed sensors read correctly. Is the Malfunction Code do to the first two?*

Wish all auto vids were clear and precise as yours. I just bought a 04 Pontiac Bonneville in wonderful condition except the abs pump had a leak from underneath the black cylinder. It was where the elec harness is mounted. Took off the module and used a whole can of brake cleaner inside /out then used permatex on the harness gasket and reattached it. Prior owner was using E brake to drive it. Do you figure the pump is burned up cause he left all harnesses connected and no fluid in the system? The brake system is bone dry I'm sure. Don't want to waste time putting module back on , replace fluid and bleed for nothing. Any advise would be greatly appreciated

Beautifly detailed. Thank you!!!!

Voltage drop would be from B+ at battery to the power wire at module. You did available voltage tests

Very very very nice! Great job!!! Thanks for this video...

Nice video I just bought 2018 dodge ram yesterday with22,534 miles on it,on my way home I got the same light issue about ABS break system I called the dealer today I have appointment tomorrow morning let see if they cover the repairs. 😞

22 civic abs module diagnosed bad. If I replace it will it need to be reprogrammed?

Perfect explanation of ABS dynamics

Very nice video. I have a vw passat 2006 B6, 2006 1.9 TDI. I have replaced the electric park brake control unit. it big on diagnosis control unit electric park brake not coded. How to code control unit electric park brake?

Great explanation well done

I'm in the thick of things right now with my 06 GMC HD2500. I 'm using an old Snap On brick so did a bleed test & know ABS motor works, but pedal blowby felt where it should push back against foot during this test. I have done a road test & speed registers at all frt & r. WHEELS . If I delete abs light & drive off,ABS light stays off during complete drive cycle. Only when I shut truck off turn back on ABS light glows but yet no codes are being registered!! truck brakes fine otherwise. everything on truck is new from last year and nothing is worn & no seized "calipers" including a new master & hydro boost. Will check wiring for bad ground or ?? Coincidence after replacing a bad RF hub bearing yet, speed sensor registers ok! Thanks for sharing your knowledge!! you gave me a couple more tips to check out !! THERE IS A REASON AND I HATE UNWANTED DASH LIGHTS !!🤣

I have a a 00 Buick that has 2 codes that came up. 1 is. C1245 the other is 2 C1298. Dos these codes have anything to do with the EBCM. Oddly there are no light up on my dash but when I plugged my computer up to the care these to came up.

Hi I have a 2013 sprinter van it’s been into 3 places to try and find the fault. The abs light came on they replaced to sensors the light went out my brakes are so soft the brake only works on quarter of the peddle. They bleed the brakes then put a new kit in the master cylinder it’s still the same they were all lost with it and it’s still the same can you help thanks

Great video thanks 👍

Thanks for you good explain Put I have problem on pump not module 1st one I change because pump pin on the motor head not release I changed the unit for this reason and 2nd one the pump get oil from all the pin inside and the oil makes short after that I listen the unit working if the car switch on or of then I changed too withe new one My question is can I repair any pump of this 2 defect of impossible If yes I thanks if you explain with vedio Thanks

my car is audi a4 b5 1996 quattro. On diagnostics, it doesn't show an ABS pump error, but all my wheels lock when I press the pedal and stay like that until I let the air out. This has been happening since I jacked the car up, started the car and ran the wheels to idle. They told me that I am not allowed to work with the quattro drive because the pump has built up pressure and now it is constantly working, and that the piston in it was leaking and does not return anymore. Is this correct and is there any other problem? 

My 2004 Land Rover Range Rover HSE 4.4l with BMW M64 TU has the DSC disabled and replaced with a coil spring system is this the cause of my ABS red light fault with no codes?

Thank you for the video

Hi we have 2012 Citreon relay ABS plus traction control faults on dash , no speedo and not registering miles , scanned got configuration fault (configuration not suited to vehicle ) Fault in the alignment of the configuration between ECU's (used Foxwell NT 530 scanner . Been into Citreon dealership (local garage advised to ) couldn't bottom fault , so sent download off to Citreon tech been told fault is ABS pump/module ! doesn't show ABS module fault on scan , reads wheel speeds ok ,What do you think

great video, dear author, thank you

Hi I have a Volkswagen Jetta MK5 2009 model, the ABS CONTROL MODULE is faulty can that be fixed or I just need to get a new module for it ? Secondly can the abs control module be cloned/reprogrammed from another vehicle into mines or I need the exact part number for mines?

Thank you for this explanation

Which VAG-COM VCDS Works for the vw golf mk5 2008

Most common stuff I've seen recently is open circuits in wheel speed sensors traced back to ABS pump

If I'm able to Run My ABS Pump with My Scan Tool and activate all the valves. Doesn't that mean that My fuses, wiring & electricals are good/intact? 2015 Infiniti Q50. Chasing a C1138 Code.

I have a Ford Fusion 2011 Code is B1676. I replace battery / replace master cylinder. Need help please

My dream to have your knowledge bravo

Hi I have a 2010 VW GTI that has abs code 01130. Brakes feel fine and all wheel sensors are good. Could it be the battery?

2012 Mazda 5. Brakes peddle drops to floor. Pumped they work fine, but after awhile of no braking then when applying brakes, it drops again. Also, could hear bearings. Replaced back brakes, calipers, bearings and still have the problem. You can feel peddle catch and then air leaves, peddle drops to floor. Was told to replace ABS HCU. What do you think ? This looks to be very expensive. Im in CA

Hi, i have a ford fiesta 2009 model. I got p0500-00 and C0031-07 fault. It says front left sensor but i have already changed it and bearing as well but still got same problem. On diagnotic tool the speed shows 0km/h. Can this be the wiring or abs module?

Cok guzel video olmus

Is there any testing on the mk20 version (early vw abs pump)

Hi, i have a 2009 Scirocco 2.0tsi. ABS & Traction lights came on randomly along with a flashing handbrake light. Took it to a garage that reset the error codes and the issue went away for about 15 miles; now it is back. Brakes feel fine, no issue with the way it drives either. Code is 16352 - Control Module - Defective. Is this something your rebuild service can sort out? Your rebuild cost is really reasonable considering i have been quoted for a new module @ £1,200 plus 5hrs labour...

Hello, thanks for the video ! Could you, please, tell me where can I buy new ABS pump online for my Ford Fiesta 1.4 TDCI 2012

Get a 2012 2013 with adaptive cruise an loose all brakes... that's a fun feeling. An can't find one.. channel b valve stuck no communication with module...

Could It Block partially 2 wheels and not show any failure or error?

What about 2014 Ford Expedition, Having ABS fault DTC B1342, once you insert key to run/start ? Then switch off remove key run/start this abs alarm will not come ?

I am getting ABS Sensor errors, front outside, rear nearside. Also power steering Malfunction, several other communication errors When i test voltage at the plug these are 9v, the other two working ones 11.9v I checked the wire continuity to the sensor. I pulled the plug of the ABS module, put 12v in on the correct pins and tested the sensor plug and got 12v. So the ABS module is outputting 9v for these sensors. Why 9v on two diagonal opposed sensors and 12v on the other two? This is a Ford Focus RS Mk2. Would each opposing pair have a different supply maybe? Is the Module in need of removing and refurbishing?

Hi. I've got abs and EBD lights lit on iveco.. ran diagnostics.. only, no braking system.detected.. where do I go from there? Please tia

my 2015 c-max hybrid will not release the brakes when in the hot sun, then sometimes flags the abs light. If I feather the accelerator, it eventually releases. Also, if I switch from reverse to drive, it will release also. The compressor sounds weak and slow. It's like it's gotten weaker over time. Braking during operation is not a problem. In fact, sometimes it's too strong, especially under 10 MPH. The dealership quoted $2,500 to replace the whole ABS module. Looking at the troubleshooting report, they're basing it mostly off the code and test values. No mention of the sensors being tested.

What do I do if the abs and TC warning light don't turn in ever? Abs and TC also don't work and all fuses are good

My 2020 Nissan has code for the abs motor pump but the abs light nor the traction control light comes on. Weird

Hello bro my mt15 V1 front brake feels spongy even after several brake bleeds, zip ties, and even after replacing mckit . But abs sensor light working good i feel abs is triggering but can’t figure out this spongy brake. Service centre guy simply told abs rotor/motor problem which costs around 13k . Im confused is this really a abs issue or any brake hose or calliper?

what if the wiring is bad how do u fix that

Hi, 2014 Ram 2500 soft pedal no brakes I can push to floor with a little brake. Did replace master cylinder. Same issue, I have no codes for the ABS system.. any thoughts

Computer won’t recognise my old repaired abs pump, any ideas? Great video btw Jaguar S type 3 litre 2004

I have question is that possible

PLEASE HELP ME, after replacing the lower control arm & the wheel hub, everything's perfect after an alignment, then 2 weeks later the ABS lite came on then a month later the front passenger side wheel started to grind even when i hit the brakes so today I removed the caliper with the mount and rotor and it still grinds consecutively ? I have a HUGE family get together this Saturday at my brothers (about 200 miles each way) but I'm scared shitless driving up there, PLEASE,PLEASE,PLEASE HELP ME...

Thank you 😊

How to resolve code in Prius 1.5 hydraulic system RR

awsome well done

Is it common issue the ABS pump to fail on Honda Civic MK8, 2006 with R16A Engine 1.8L? My Break pedal travels slowly down when pressed, travels excessively on the first try to stop, and its stopping but slowly. The second step on the pedal then it grips and stops great. Would that be a faulty ABS pump fault or something else? Thanks. Its great to see that it can be repairable as the original unit is about 500-600 Euros from Honda. I have no lights lid up on the dash.

Hello. My kia sportage sometime shows ABS sign and wheel deviation signs. it stops by itself and come back from time to time. no engine check signal. I am not sure if related to driving in water or not. Do you have an idea?

hi, my car is 2011 year ford fiesta 1.6s. I have faulty ABS code U3000, I cannot to found the problem pls help. Thank you

Thanks!

Hi guys. I was looking for some similar situations with my car and I think you might help me a bit here. My BMW 2019 G20 320d has been just serviced for the 3 yearly compulsory brake fluid change. When pick up my car I had the lamp blinking for traction control as soon as I’ve left the dealer workshop. I could not go uphill due to power loss in the first 500m until the lights stopped blinking and power came back. When driving the car braking in city at small speed everything seemed OK but at higher speed I felt that I couldn’t stop the car and I was definitely applying more pressure on the pedal then before. I was so disappointed since my brakes were the upgraded M Power type and they used to be so so good until then. The dealer told me that the process is automatically done by a so called robot and there were no mistakes, then agreed to change the fluid once again. Same situation after second fluid replacement, traction control blinking lights, no power and all normal after few minutes. Somehow the braking improved a bit but it is not what I can recall from before changing the fluid first time. I feel very disappointed, I will not return to this dealer again , the car is almost new 22K km (13K miles) and I don’t know what to do from here. Someone suggested me to vent the ABS valve block by actuating the valves with a computer or so?! The dealer says the car is fine but braking from high speed is not what it used to be … I do have still another 2 years of warranty from BMW and I like the car, but how do you suggest to solve this issue please? Looking forward to your reply. Cheers. Bogdan

Will a bad abs module cause my brakes to lock up? Then i have to loosen the brake lines at the master to relieve the pressure.

Somo Zuriii,, Hongera Sana

Hello, I need help, I have a brake workshop, they brought us an iveco daily 35s15 2019 ambulance, when you step on the pedal it goes very low, it does not show an abs failure in the ecu, the pump has no problem, neither do the wheels, everything indicates that the fault is in the abs, it has already happened to us with several vehicles, it is as if the brake fluid left somewhere inside the abs module, has it happened to you?

Please Chevrolet equinox 2012 with code C56D, electronic control unit hardware malfunction, please what does it mean

In some cases fuse faulty but service center guys change whole abs control unit 😰.

Can hear this guy doesn't just talk he knows what he is doing. And is correct with voltage drop. From my experience and as a electronic technician old school one taught me also. A voltage drop can also be to a short circuit that has some resistance. So it can cause problems like on cars your battery life gets shortened. And you basically get 2 types of short circuit one with 0 resistanc which causes fuse to blow usually. And the one with resistance so the fuse doesnt blow yet you get battery drainage issues. And i have seen it in the past. Few months ago i worked on a Toyota hilux which had extra battery in for camping lights and so on. The owner asked me if i could test if there wqs 12volt at the connectors at back of rhe vehicle. I tested the ground 1st and its fine. 12v side dead. So went to engine compartment test that battery 0volt! He is like what?! 0 volt?! That cant be. I also tested a 100 amp fuse which is also fine. So he went in to make some coffee and now my brain is thinking and im like yeah 0volt is extremely flat. So i removed the positive terminal on that battery tested again and i got like 2 volt literally 😂. The moment i touched the positive terminal on battery volts drop immediately so theres a short circuit somewhere in that harnass. The client also said the people that fitted his reverse camera suspect that they might have damaged some wires. So yeah just to be extra safe i insulated the positive terminal. So in mean time the client can take vehicle to the workshop that fits the camping accessories and so.

I have a 2019 ford transit all these lights are on abs,tcs, and uphill assist are disabled as i had to unplug the abs pump cuz it wont stop running killing my battery. Any thoughts what this could be? Please help

I had a used abs module put on my Volvo S40 T5 and now it doesn't recognize the modulator and I am not certain how to fix that? Can you help a girl out here and possibly tell me how to get it to recognize the new replaced part?

Hi i have honda accord 2013 abs , fraction and hand break light is on can u suggest me thing...thanks

2011 Audi A4 ABS module has lost communication with the car. I have a used work in working order but it will need to be coded. The stock ones doesn't work and has my car in limp mode and disabled a ton of things. Sometimes you'll hear the stock one that's faulty clicking as if it's trying to work. Any ideas from anyone on what could be going on or can someone point me in the direction on how to code the new one so I can install it. Thanks in advance.

I have a Mazda atenza wagon an my abs module keeps running after I turn the car off completely us there any reason why it would be doin this sorry I dnt know much about cars just wouldn't mind abit of info if some of e can help

can you help me with this one 2000 mk4 golf 1.8t basically i swapped me3.8 to me7.5 and now got this code 01276 - ABS Hydraulic Pump (V64): Signal Outside Specifications ive checked fuses but dont know what pins have power on the abs one person suggested that the early golfs used a different abs module to the later ones and this could be the problem

The brake fluid does not reach to the right-back wheel of my sonata car. The abs light is off. Could you please state possible reasons for that? Thanks a lot.

I believe I've had a faulty ABS hydraulic pump on my VW Corrado SLC for many years now I took a pair of alligator clips from the battery to the motor and all I heard was a click, the motor never turned on, that's how I know it's faulty. I've got the worst parasitic draw because of it. I'm going with a non ABS swap!

The ODB2 reader reports no codes. The dash panel gives an ABS related message. The motor attached to the ECBM unit runs continuously. Any advice?

Kompenen apa yang rusak jika muncul kode kesalahan U3000 control modul supervision software failure? Apakah ic yang rusak? Mohon di jawab. Terimakasih.

I have a seat ibiza. My abs light and handbrake has come on and buzzing from pump even when engine is off. Even took fuses out and still buzzing. Gotta disconnect battery to turn it off

I have a Toyota estima hybrid 2013 with abs fault can this be tested or repaired ????

Hi! I been noticing a weird safety issue with my bmw f20. Whenever I braked hard, my steering veers to the right, an indication my left front brake is not functioning well? A quick trip to a workshop ends up in both front left and right rotor and brake pad change. However when the mech tried to perform a bleeding of front right brake, he said it was not bleeding well enough. After many attempts he decided to check on my abs pump. He disconnected the line out from abs pump to front right, and upon pressing the brakes, little brake fluid seems to be coming out of the abs pump supplying to front right. Is this a sure tell tale sign of faulty abs pump? Or should I carry out the wiring test as shown by you guys

What is the name of the place in California that repairs the ABS brake actuator MOTOR? I know they exist because I used to have their website bookmarked. Then my phone died. Now I can't seem to find their website.

My toyota corolla 2008... when i switch off my ignition the abs keeps vibrating until I disconnect the socket from it please what can I do?

Could you please tell me if a scan tool is necessary to bleed the brakes on a 2005 K74 Mitsubishi with ABS brakes to remove the air from the ABS module ?

I have Peugeot 301 with abs problem light on when I diagnosed it permanent fualt front weel sensor no signal the four sensors has no signal so I change the abs module it did work and I took the module to another car it work fine and I change the four abs sensor it did work I change the week bearing it did work I checks on

when going over 60 in a 2012 honda pilot, sometimes vtm4, traction, and abs light come on. After you turn the car off and drive down the road, they disappear. Anyone know the cause. Might be an abs sensor but who knows...

I have a 2007 Tahoe. Apparently my BPM is discontinued. My brakes are soft. Any suggestions?

Hi im at my wits end with my 2000 Mitsubishi Evo 6. The ABS light is on . I have cleaned the wheel sensors with no luck. One interesting thing is , when i turn the ignition on the light is instantly ON and doesn't go off after 3 seconds as it should. When i start the car light is constantly ON (without the car moving or rolling). When i do drive the after about 10meters the AYC light comes on. Im guessing its not an AYC issue but more a ABS. What could it mean when the ABS light is constantly ON from the time the ignition is turned on ? Any help is appreciated ? Is there a manual way to test the pump or check if its working ? Any way to test the ABS ecu ? thnx

My impalla 5.3 says internal ram failure. Can this module be repaired?

I have a 2019 Nissan Frontier 4L V6. Code is C1111 (Pump Motor). I sometimes hear a clicking noise in the motor motor assembly.

Hi, I have an issue, I parked my w204 c300 4matic mercedes 2010 for about 3 weeks and when I drove it for like 4meter away the brake pedal went flat momentarily ( happened 3 times ) after which it normalized, since then I haven't driven it again, please I would like your help on what could be the cause

Hello I'm in the US every 2018 Ford Transit connect the front driver wheel in the back passenger wheel both calipers are dragging I have already rebuilt the brakes to try to solve the issue and replaced one brake line did not solve the issue I think I have a bad ABS module keeping pressure supplied to those to calipers I don't know what to do please help me😢

Hi. I have an BMW E87 with error 5E20 . Can help me ?

I got tested my car’s abs from the company and they told me my ABS valves are faulty. What’s the solution?

What would cause a module to run even when the vehicle is off cause dead battery

I'm driving scirocco 1.4 tsi and the car had error code 01130, anyone know if this really ABS pumps faulty or maybe sensors, fuse etc. Thanks in advance!

Does anyone have any reviews of this company rebuilding the unit and offering the lifetime warranty thinking about doing it???

UO121 Code astra J . Is this abs control module fault ?