TOYOTA PRIUS HIGH VOLTAGE A/C COMPRESSOR | AIR-CONDITIONING

TOYOTA PRIUS HIGH VOLTAGE A/C COMPRESSOR | AIR-CONDITIONING | HVAC

Рет қаралды 50,768

4 жыл бұрын

High Voltage A/C Compressor Toyota Prius Hybrid Gen3
#toyotapriushybrid
#highvoltage
#airconditioningcompressor
#gen3
#3thgeneration
Hi Guys!! Please click Button Subscribe and Button Bell, Dont forget Hit LIKE! and please support this channel for future content.
Thank You for being here.

Пікірлер: 63

@DCSpeed2 3 жыл бұрын

Thank you for showing the inner workings of this compressor. I learned it is a scroll style compressor with a 3 phase motor to drive it. Both an excellent choice for longevity and reliability. Excellent demonstration!

@batrisyiaramli6792 4 жыл бұрын

👍👍good sharing

@-gg9f 4 жыл бұрын

شاطرياعيني شاطركل افكرك حلوه 🤗🌹🌹

@ramboperera760 3 жыл бұрын

Thanks,

@ilovetacos210 2 жыл бұрын

This song sounds like I'm on hold with a budget insurance provider.

@tbond1007 Жыл бұрын

I find it interesting that when you taking the compressor a part, the two snap rings at the power thermals I saw only two terminals, when putting it back together three terminals were present. where did the thread one come from?

@fairildin9394 4 жыл бұрын

mohon support channel saya...promote dengan kawan2..lebih banyak video yang akan saya share dalam nie...

@safwankhalit9033 Жыл бұрын

Saya nak tanya sikit, boleh tak kalau saya nak pakai compressor ni pada proton waja?

@maggiejetson7904 Жыл бұрын

It looks like a very compact and self contained design. I wonder if it can be repurposed into an inverter fridge using DC power alone (after some CAN bus based thermostat).

@marianayusof7639 4 жыл бұрын

Boleh blajar ni boh...

@user-ij4bh9pk6z 6 ай бұрын

❤

@west_park7993 Жыл бұрын

many people complain that the pins on the black 6-pin controller connector bend easily. i removed the 2 special bolts and tried to pull hard, but these pins are also soldered to the PCB of the controller. I should have un-soldered these as I pull. Still, the problem remains, where do I find exact 6-pin connector.

@wpcote108 4 жыл бұрын

What was bad in this compressor? What did you do? Replace the motor bearings? Thanks!

@maggiejetson7904 Жыл бұрын

probably just a junkyard pull for teardown video.

@west_park7993 11 ай бұрын

Prius 2012 V, 147,000 miles. AC sometimes stops working while driving. If I stop the car, turn the engine/computer off, and restart, it works OK, and it works long time. Blows cold air again. Any idea?

@wpcote108 2 жыл бұрын

What did you replace inside this compressor?

@BAWA2024 4 жыл бұрын

Aku hanya penonton..

@Dien6Amie 23 күн бұрын

I guess you just take it apart then put it back together without doing any repairs. Is that correct?

@expresspa 4 жыл бұрын

what tool you r using for those special head screws?

@fairildin9394 4 жыл бұрын

picclick.com/BGS-Tools-pro-Special-Socket-Wrenches-252709672577.html you can use this socket...if suitable...because this socket for remove defective nuts..be careful when you use this socket...i hope that can help you...thank you support my channel...

@troylollysaf9311 2 жыл бұрын

@@fairildin9394 I have 2010 prius with broken AC compressor. Can i still drive it without fixing it? Will it overheat my hybrid system?

@bisharatali7471 3 жыл бұрын

How much oil in this compressor

@user-ij4bh9pk6z 6 ай бұрын

@t63a700 4 жыл бұрын

The video sounds better muted.

@west_park7993 Жыл бұрын

the black 6-pins connector on top is a frequent problem. these pins can bend very easily. it is impossible to get them straight, unless you put it on the bench. now, there is a solution: go to junk yard and get this damn controller.

@west_park7993 Жыл бұрын

Now, you will ask why on earth the pins will go bad. I had to replace the thermostat. spilled some pink coolant fluid. it contains H3PO4. This makes it electrolyte (or "lectrolit" as per the movie Idiocracy), i.e. conductor. you do not want electric conducting fluid inside the connector, it will short all pins. I washed it with water, but then, there was water in the connector, that is like a cup. I used a rug to absorb the water, then I realized the pins were bend. Did not know how thin they were. Now, going to the junkyard to get one of these controlers

@JohnPeter-yf5jf 3 жыл бұрын

You think you could replace Just that top controller with out Opening the system? Pin on mine just broke. Thanks for the video.

@troylollysaf9311 2 жыл бұрын

Pin on mine broke too. How you fix it?

@preludethomas1061 2 жыл бұрын

Did you ever try to fix this? I'm in the same situation.

@troylollysaf9311 2 жыл бұрын

@@preludethomas1061 ebay sells used prius ac compressor for 99 bucks. However to replace top cover only you have to remove thermostat at the top. To remove the whole unit you need to remove it from bottom of car and release freon. Let mechanic replace its gonna be 250-300. I sold my prius so didn't fix it :D

@preludethomas1061 2 жыл бұрын

@@troylollysaf9311 Thank you, so I can remove just the top cover without releasing the freon? If so, that is good news.

@rotcataergeht 2 жыл бұрын

@@preludethomas1061 but you will have to release coolant instead.

@Alan-rb2rx 2 жыл бұрын

Is the inverter drive board pressurized? What I'm asking is... Can you exchange the inverter board on a system that is charged and not have to recharge it?

@maggiejetson7904 Жыл бұрын

Doesn't look pressurized to me, only 3 bolts for that size of a rectangle gasket only for water proofing. The snap ring for the 3 phase going into the compressor motor also looks overbuild if they are pressurized.

@west_park7993 Жыл бұрын

there is only electronics there. no oil. therefore, no freon, no pressure.

@madrizlanjamal2274 11 ай бұрын

voltage compressor to manual test??

@west_park7993 Жыл бұрын

update: I was able to remove the 3 long bolts and the 200 V DC electrical connection, without touching the engine coolant elements (thermostat housing and water pump). The AC compressor hangs on the freon hoses. I was able to remove the 3 bolts on the top, they are standard M5, with E Torx heads. I do not have a torx head tool, but I got from freight harbour tool set 66566. It is used to unscrew bolts with damaged heads. Then I placed the electronic controller on the table. The 6-pin connector is held by 2 bolts, M3, with their own special E-Torx heads. I was able remove them with a pair of regular pliers. I applied a slow continuous pressure, did not squeeze, because if you do, the pliers pop-off the head. I replaced all bolts with standard hex heads. It is important that this controller is bolted tight, because the 200 V DC does not mix well with water. The 6-pin connector has a little hole that leads to the space below, so it is very important to have a air tight seal there. A bit of silicon grease also helps to keep air, oxygen and salt away. I ordered a used compressor from ebay for $70. Amazon: only new, around 300-400. Rockauto-same price, out of stock. car-parts.com-only used between 50 and 500. Autozone: 1507. WOWOW!!!. Since the problem with the bent pins is so frequent, then smn should start repairing these. I tried to pull out the 6-pin connector, but it did not come out smoothly, and I stopped. When I get the replacement, I shall try again/

@poprawa Жыл бұрын

That's much simpler, than 5 piston variable stroke :v

@mydogblack6685 3 жыл бұрын

Are you able to unscrew the 2 small bolts that are by the black electric plug connection.

@preludethomas1061 2 жыл бұрын

Did you ever end up trying to do this yourself? I just broke one of the tiny pins inside.

@SethSchneiderw 2 жыл бұрын

same here

@preludethomas1061 2 жыл бұрын

@@SethSchneiderw I ended up doing it myself, instead of removing the 2 smaller bolts near the Compressor control electrical connector, I removed the 3 slightly larger E9 or E10 female torx bolts holding the whole top plate on. I used an E10 socket but it may actually be an E9. FIRST pull the HV orange plug on the HV BATTERY in the rear cargo area to Ensure you aren't electricuted when you unplug the HV Orange cable going to the Compressor. At the Compressor, loosen the (3) E9 or E10 female torx bolts, I had to lightly tap the bolts with a hammer and apply alot of downward pressure to remove those bolts. Remove the HV orange cable from its retaining bracket and then slide the green retaining clip on the orange connector completely out. Then you can remove the connector and then the 3 bolts you loosened and the top plate is off. You can either try to fix the connector/pin or just replace the whole top plate. Hopefully that's helpful, I couldn't find that information anywhere so I did it myself.

@SethSchneiderw 2 жыл бұрын

@@preludethomas1061 thanks a lot for sharing what you did. I was able to bend the pin back into place with a lot of finicky pliers work, but I'm afraid that pin might snap because of all the bending. If it does I'll know how to approach it again.

@preludethomas1061 2 жыл бұрын

@@SethSchneiderw You're welcome. People need to help each other out when they can. I did the same thing with bending the pin, unfortunately mine was bent too far and snapped right when it was about to be straight.

@kushandhananjaya3116 4 жыл бұрын

How to chek fuse honda vezal

@LuisRomero-kt7hk 2 жыл бұрын

Como probar si le llega corriente?

@rondhole 4 жыл бұрын

What is the point? Dissembled for what? Are you replacing any parts that worn out?

@pashko90 3 жыл бұрын

No. This is just to see whats inside. For exsample if you want to use it for EV applications fo exsample.

@rondhole 3 жыл бұрын

@@pashko90 ok, just for curiosity, thats a big deals for your time. Prius compressor is regular scroll compressor like in our high end home AC or heat pumps.

@Dien6Amie 23 күн бұрын

I do not think any parts were replace.