I never realized how simple this process really was until now, thank you.

Very slow and clear speaking, step by step...easy to comprehend..great video.

My Dad made this sound like a pain in the ass timing distributed cars. After watching this I feel like NEO on the Matrix downloading new knowledge. I just learned how to time distributer engines. Thanks teach!

Thanks mate. Rehabbing a 1990 4x4 3VZ-E 4x4 and trying to get rid of a lumpy idle, sluggish performance and 13mpg it's had for years. Runs fine at rpm over 2,200rpm but has like a misfire at lower rpm's.. The search continues... I know these engines are suppossed to be on the smooth side..

A detailed video on calibrating/setting air fuel mix. Would be great. I changed the intake and it ran way to lean. I could never find the sweet spot and ended up with a burnt exhaust valve.

Really enjoy your vids. Positive tone for stuff that can be scary to some of us.

Great video! I recently did my head gaskets on my 94 toyota 4runner 3vze motor and I put it back together and tried to time it but was not able to get it perfect... I had no clue you had to jump the diagnostics so I will try that and see if I can get it running better

Rings back fond memories

Ha... I got one of those! I cant believe you use your bare hand to adjust it! I've been zapped so many times that I use a piece of wood and a small hammer to adjust the position of the distributor!

Sir! You saved me several hundred $$$$ with this video! Thanks a million!

Move to the East Coast and we will be rich!! Nice video ...... I very much appreciate your steady approach to making the proper mechanical service and repairs. Thank you, “My Friend” !!

I like the way that timing light flashes. Would be good to use in the bedroom or in the study.

That was great, I have never been very good at using the timing light. Nice job.

Perfect explicación, Thanks 🙏

Move to the Midwest. I can certainly use your services!

This video gave me flashbacks to my 1974 Celica.

Just did a timing belt, water pump and tensioner on my own . runs great. Now to check this timing thing... great video it has 210,000 miles . Found so many short cuts others took..,

I Have 2 Timing Lights Haven't Used Them In Many Years All Those Vehicles Are Mostly Gone In The North East They Went In The Rust Crusher

best toyota videos

Excellent video. Thank you.

I miss my 1990 Toyota pickup with the 3vze engine. :(

Love your videos and your style, thank you!!

Thank you sir very much, great video and explanation!

Nice video

Was the wire jumper left installed when you set the timing?

Question: (I have same exact year and motor) The closest I can time mine is about 18 BTDC. I removed the distributor cap while crankshaft is on 0 BTDC, and the rotor points about 4 degrees (1/2 inch) left of the #1. Should I try removing the distributor and reinstalling? In other words, It is supposed to be at 10 degrees BTDC, but the distributor will not rotate far enough to get it there. Thanks!

Another great engine I have two 90 series Prado with the 5vz engines very reliable with basic maintenance (that is the smaller Landcruser brother) not sure if you guys have them in the USA .Peter from Australia.

Awesome video, thanks so much.

Thanks for sharing this video, I am in process doing this,thanks again

I would add that before anyone does this the engine should be at normal operating temperature and normal idle (which I believe is ~8-900 rpm for the 3VZ in my 94 truck). I also read that you need to make sure the air-fuel mix is correct first before re-adjusting the timing. And most people seem to recommend advancing the timing on the 3.0L a little higher at 12 to 13 which is great for 87 to 89 octane fuel. Some people run it even higher at 14 and use 93 octane. And as you did, I would also install a fresh set of plugs and new cap and rotor first before doing this, and clean or replace the air filter too. I like the system to be "fresh" before checking timing. And lastly, I always look for cap/rotor with copper or brass terminals on both. They easily last twice as long and you can lightly clean off the ignition deposits with some 300 grit sandpaper which I do every 15-20k miles. The aluminum type is just junk in my opinion. PS - Given your accent.. do you work on Volvos lol? You sound Norwegian!

cool thanks

That was entertaining. thanks

Please does anyone know how to adjust the ignition timing on a 1997 Tacoma 2rz 2.4? I'll be very greatful . The distributor has no way to adjust. Any other way to move the ignition advance?

I've got a 3-VZE and the timing does not advance when the engine revvs. The engine timing is supposed to advancs faster than 10° BTDC when above 800 RPM, but mine stays at 10° no matter what revvs it's at and it causes severe misfires and stumbling. help?

My car wont start since i took the distributor cap off when changing the alternator. Do i just turn the crank to 0 TDC and then turn the distributor rotator to cylinder 1?

I always wonder how to do it but know I know. Thanks

With the distributor adjustment at the extreme end of it's range, it makes me wonder if the timing belt is off a tooth.

Man, my timing is way off. When I set it to ten the distributor is cranked all the way one direction and it runs like crap. Any idea what would make the timing so far off? 😢

I have a hilux 2.4L 2rzfe from 1998. It has two distributors and it is not possible to rotate it as in this video. How would you adjust the timing in this type of engine?

Thanks for the video. Long time viewer here. Question, I have a 3.0 t100 what coolant would you recommend? I don’t believe the pink long life was made in 1994, should I use the green predstone or Toyota pink? Thanks you for your time!!!

ممكن طريقة تجميع طوبوات من المحرك

Very entertaining video!

where does the fuel pressure regulator vacuum line go to. one of the metal lines behind the egr valve. 22re motor

My 5sfe 2.2l camry has high postive long term fuel trims at idle 20% when revved past to 2000 rpm it drops to postive 5% , where can I start yo diagnose issue?

Is the white mark already on pulley?

I bought a 1995 Toyota 4runner Sr5 V6 3.0L the owner said it needs a tune up. (It drives fine) how much would a mechanic charge me to do the job? Thanks in advance

Thank you!!!

I have the same engine (1994 Toyota pickup V6 3.0/3VZE), and I'm getting a code 24 and code 31...rough idle, rich running, hesitation sometimes when i press on the gas pedal, check engine light on, and occasional backfire when first starting (cold). The truck came with an EGR delete set up, as well as a cold air intake simplification mod when I bought it. If you (or anyone) could offer some guidance, I am by myself and really need help. Thanks!

Hi , are those calibrations are the same for a 95 Toyota 4Runner with a 3vze ? Thanks

Nice West Coast pickem up truck...ah no rust..whats it like Peter?

Customer broke it; wants you to fix it

Very informative video! What is your shops name I’m also located in Northern Ca. Cheers.

I just got a used Honda generator and the plug looked like your top middle one, but with even more buildup. I've never seen that before. What causes that?

Love your videos! Question.i have a 92 4x4 automatic 4runner. Takes a very l9ng time to warm up and while driving over 60 is over cools and idles high until operating temp. Any ideas what the issue is?Thanks for the help.

I have an older Toyota, too. Which brand of parts did you get for the distributor cap and rotor?

Dont you have to make the white mark when #1 piston is TDC? if yes, how did you determine it was at TDC?

Where can I find a radiate for same truck

Nice one!

Ok I am a subscriber and seeking advice. For 25 years I own

is this something i can do in my driveway?

Where are you located ?

Is this the same for a 1992 camry?

I didnt understand how the light gun works,, can you please make a video on it ?

How do I reset timing if I installed distributer without aligning the notches and cranked the engine? Please help. Also where are you located?

I have 1999 Toyota Corolla LE I want to dump and fill automatic transmission what type of fluid do I use it says Dexron 3 on the dipstick and the power steering cover

What is code 42 on a 94 Toyota 4Runner V6 4x4

The white furring on the spark plugs is bad sign. It's oil burning on to them from wear

Ah the 3.0L V6 Boat Anchor.

Hi friend, do you also repair Honda?

my idke drops to about 500 rmp after warm up. ive adjusted timing but can figure out how to get a 800 rpm idle... help?!

Will he ever have a cheap Toyota project for this channel?

I have the timing just at the back side of that bolt which is about 30° btdc. I also adjusted the fuel inlet valve on the fuel rail to let fuel in faster. I had to adjust the MAF aswell. She hauls arse now ;) Please like my (sent it) Video ✓ kzfaq.info/get/bejne/aNWWhtep292upmg.html

that motors burning oil... look those plugs...

My 91 truck timing is right on 10 perfect. And it runs quite smooth (passed smog check easily). But it has very low power and acceleration. 🫤. Could the timing affect this?