You made it look pretty easy, but mine was around $50 ish.. and how they had the old trailer jack on..makes it where the new one doesn’t go in the same place. I also wish I had man muscles instead of Elderly girl power ..I’m an old lady without any real tools except for imagination determination and being a little pissed off.! Lol .. I appreciate your video. Thank you.!
@Fireship17 жыл бұрын
Just installed one just like it from HF on the same kind of trailer as yours (carry on brand) It's an awesome trailer and now even more so with the addition of this jack.
@denoftools7 жыл бұрын
Every time I use the trailer I am stunned by how much more useful it is with that jack stand.
@missw1513 Жыл бұрын
I'm going to try to install mine tomorrow on my hotdog cart! Wish me luck...signed A WOMAN😂
@jamesm5683 жыл бұрын
Why did you put the brackets on backwards not per instructions?
@johnnyarredondo56514 ай бұрын
Good effort but keep the camera tied down or does it shake so much?
@briankruse35846 жыл бұрын
I replaced one in my boat trailer. I have the one with a grease fitting and I lube the bearing buddies and hitch every spring
@koldenrjk4 жыл бұрын
Not sure you should have to lift like that at the end.. doesnt seem right
@maggierobillard Жыл бұрын
Thank you, your video was so helpful I'm curious if you can add the double caster wheels to this jack? This swing arm fixes half my problems--lifting the trailer--but the single wheel still might sink.
@primodesiderio2666 Жыл бұрын
Looks like you put it on the wrong side also you put brackets on backwards.
@JamesBrown-ey4mt7 жыл бұрын
Thanks for your comment. I figured out if I used a 3/8" bolt instead of the 10mm that the jack came with...it finally works. Yeppie!
@ptmiller983 жыл бұрын
Love the cal guns! License plate cover🤟🏼🤟🏼🤟🏼🤟🏼🤟🏼🤟🏼🤟🏼🇺🇸
@denoftools3 жыл бұрын
Wow, I forgot all about that. I live in a free state now and just can't imagine how bad it must be for one back there
@TheHelado367 жыл бұрын
Thank you I knew I was doing something wrong !
@warf-oc9yz7 жыл бұрын
Red Beard where you at ? Miss you and the bear.
@MurrayEstes5 жыл бұрын
Thanks for the tip with power tools.....be careful :)
@minerdad02 Жыл бұрын
85.00 here at Cambodian Tire in Kirklandlake Ont
@robskater946 жыл бұрын
Just got one from northern tool for $20! Super cool
@janjaf8442 жыл бұрын
So I'm moving and need to transport swing set and pull my pontoon boat. But I can't seem to pull the thing to lift up the wheel, is the truck too full?
@nenigma1 Жыл бұрын
6 years later... n here i am. Harbor Freight just had a sale on these 1k pound version.
@brokenhearted25 ай бұрын
What tools you use.. Size?
@fabianpachoek7731 Жыл бұрын
Wheel jack is Best on market
@uncno6 жыл бұрын
What if the trailer tongue itself is too small for the wheel jack?
@denoftools6 жыл бұрын
Like it's too short when the jack is swiveled up? Or that the bar is too small for the mounting bracket?
@uncno6 жыл бұрын
Red Beard and The Den of Tools the bar itself is too small for the mountain bracket
@denoftools6 жыл бұрын
Hmm, can you send a pic?
@michaelkrakofsky98904 жыл бұрын
awesome vid brother ty
@ratled12 жыл бұрын
Had to give it a like.... CGer
@mitch50774 жыл бұрын
I'd like to see your spare mount. my tires are 13"
@beebob12796 жыл бұрын
The pivot on my jack is frozen. Suggestion? I want to keep it and not replace mine.
@denoftools6 жыл бұрын
First I'd try a penetrating oil. If that doesn't work a heat gun and then ice bath. Once you get it moving, strip it, clean it and try it again.
@solomon70724 жыл бұрын
Can you use the Jack stand with a full load of Mulch in the trailer? Will it hold?
@denoftools4 жыл бұрын
I don't know about mulch but I had the trailer loaded up with 3 tool boxes completely full of tools. It was most certainly over the weight capacity of the trailer. And I had zero problems most cranking it up or down
@solomon70724 жыл бұрын
@@denoftools Thanks.
@JamesBrown-ey4mt7 жыл бұрын
mine won't fit the bottom bolt won't go through to the other side and if I go down to next hole the gap is almost an inch.Help!
@denoftools7 жыл бұрын
The real issue is that the bottom bolts are up against the bottom of the trailer arm. The top bolts are there to clamp it down.
@thomasroderick70798 жыл бұрын
hi
@BAHRAMCR6 жыл бұрын
I got this at Walmart, but this is too tall for my trailer. Any suggestions?
@denoftools6 жыл бұрын
The only thing I might suggest is trying to see if someone sells a smaller one there's really not much of a way to adjust it past the the lowest setting.
@paganpoetprophet64415 жыл бұрын
where you get the drilled channels you ran u bolts thru
@denoftools5 жыл бұрын
came with the jack
@abdul08117 жыл бұрын
can you post a link to the padlock you have
@denoftools7 жыл бұрын
Sorry, I missed your question. It was part of a combo kit by Reese. www.tractorsupply.com/tsc/product/reese-towpower-tow-and-store-anti-theft-lock-kit?cm_vc=-10005
@markzimmerman97365 жыл бұрын
where did you put spare and with what mount?
@denoftools5 жыл бұрын
Right now I'm keeping the spare in the trailer itself I have not found a mount that I like then we'll work with the side walls on this trailer
@markzimmerman97365 жыл бұрын
@@denoftools thank you i may put ubolt up front on top rail just drill 2 holes i guess and stand it on tounge should work
@JohnFinityRealtor5 жыл бұрын
30 seconds of content packed into a 5 min video ;-) :-(
@stackontechnololgy Жыл бұрын
Useless information... You said or did nothing
@barbarastotler9007 жыл бұрын
Couldn't watch it....the fast forward made me nauseous