A tip on the double sided tape in a vehicle. If you are using 3M VHB tape there are many different varieties for different purposes. You want to make sure you get a heat resistant version. Otherwise on a hot day in the summer the tape will fail. Learned this one the hard way. You want 3M VHB 4991 it's gray in color it is what is on the go pro mounts and it works great. Some of the other variations will fall right off as soon as it gets hot.

Well made video. To avoid fire, make sure you put a fuse (and maybe also a breaker) on the electrical wires very close to the battery. If the wiring gets pinched or the insulation rubs through the fuse will cut the power. I saw another overland KZfaqr burn up his off-road rig because he fused inside the passenger area of his vehicle. He even used his fire extinguisher. He was left stranded in the middle of nowhere. And food for thought: A 50 watt GMRS radio gets REALLY HOT with extended talking, so it should be mounted in a well ventilated location.

By far the best Midland install video I’ve seen

40 yr trucker offering my 2 cents here: you can get 'em in a pack, but very short bungee's are nice for hanging the mic from above. The metal hooks on either end are good for affixing one end from somewhere on the ceiling/roof or maybe sun visor (wherever) and then the other end (usually) at the point where the cord spirals. If you get your placement right, it can swing all day long without hitting anything (or anyone!) but it's always within reach, even for on-going conversations. DOT pulled me in at the St George Utah Port of Entry a few years ago for a level 3 safety check. When he opened my door he said, " Oh. I see you have a CB. You're Old School. Don't see CB's very often anymore." No wonder it got so quiet out there! Lol! Thanks for all the great videos. Now... where to put everything in my '59 Willy Wagon!

The downside to running all your accessories directly to the battery is that it soon becomes a rat's nest. An alternative, with no downsides, is to install positive and negative bus bars. Doing that requires that you to run only ONE positive (fused to max expected combined load) and ONE negative wire (min 8AWG for each) to the bus bar. Now you have multiple terminals to which to add accessory power as needed and a good ground is always assured. Be sure to fuse the power wire to the accessory. Using auto-loom, you can make your wiring very neat. Amazon has a complete selection. Another trick I use is to color code the power wires. Having several red power wires can make it difficult to troubleshoot. However, by using different colored heat shrink or electrical tape to mark each end of the wire(and at about 2 foot intervals) it is easy to trace them when needed. The same can be done for the ground wires. The only accessory I ever wire directly to the battery is a winch. I use welding lead cable for that and color code them. I also use Anderson plugs to make winch maintenance easier when needed. Another plus of the Anderson plugs is that you can unplug the winch and plug in a set of jumper cables or other high-draw accessory when needed.

Finally someone who actually shows you the “install” part in a video! I’ve seen countless videos that claim “install” in title but all the show if the unboxing and then the radio turning on and it’s feature!! Thumbs up for you sir!

I just got this same Midland set up with the 6db antenna for both my son and I. Works awesome and the range is way better than I expected. Great set up Brad and clean install👍🏻

So excited to wake up and see another TR video! Amazing way to start the weekend

Me and my wife use the micro mobile and we love it. Whether wheeling or long trips it is a tool we have grown very fond of.

Cool vid! Thank you! I got my GMRS license a month ago and very happy that I talk with many users from all over the place. I got a Wouxun KG-SX20G 20W and has been serving me well. Reaching repeaters 50+ miles out while indoors. I just ordered the Wouxun UV9 Pro for my HT.

These are my favorite type of Trail Recon videos!!

Nice clean install. The midlands with the controls on speaker mics open up a lot of options.

Great video. Been mulling around in my head on how to mount my GMRS in my 2016 Wrangler. This video helped. Thanks.

Great show. Those new broncos are nice

Midland has great customer service. Installed the same base unit and it was perfect for 2 months. Starting cutting itself off, sent them an email and proof of date of purchase, they sent me a new one no questions asked! We also have a couple of the handhelds for spotting other drivers.

Nice 👍. I believe S. Cal. has a linked GMRS repeater network which can extend the range of your comms. For those willing to study for the Ham Tech exam , the Winsystem ( UHF/VHF) allows you to link to a 100+ repeaters including international coverage. 73!

Very timely video. I was just thinking about these options a few days ago. Thanks Brad!

Great video, in my Bronco I used an ARB tire plug ream to puncture the same grommet and used the plug pusher to insert the wire. I know I sacrifice an inch or so of wire, but I know it’s water tight.

Mounting my Midland GMRS is my next project. Thanks for the ideas!

I just used Mountain2metal adapter to install my Midland radio in my 2022 Bronco. It puts it right above the glove box. I also used their antenna mount and Molle panel on passenger side. Worked great.

Great video. Both jeeps and Broncos have some limited spaces for radios. The good thing about this particular radio is that is completely remote-mounted. Which is just that, “remote”. If you are having trouble finding a place to mount this radio in the spaces you were suggesting in the video, or perhaps you want the radio mounted in a completely different location, you are only limited to how long you can run an Ethernet cable and power cable with a coupler on the microphone end to connect the male end of the microphone connector. All my radios in my Jeep are mounted under the my cargo area in my Jeep. Tucked away, and all you see is the control head in the cab area. I’m not a fan of mounting a radio on the side near the driver’s legs. Locations as to where you can mount this radio are endless with just a few feet of power cable and an extended Ethernet cable and coupler to extend from the radio’s physical location to the microphone.

Great video. Just thought of a con of the hard mounted radio. If your battery dies, your radio dies. Like you have said many times though, carry both. Pretty neat stuff!

Great quality video, install, and presentation. Enjoy that 275 and Bronco!

Nice video Brad! Loving the Bronco content

I used to use only handhelds before I realized the convenience of a mounted radio. In my opinion mounted is the only way to go. I use Midland MXT400s in the Jeeps, and have a few handheld GMRS radios I can grab when getting out and still want comms.

The Gromit hole is for the clutch - Nice video

Just put the midland in my jeep ❤️ still learning the repeaters in my area

Thank you for another great video. Very informative (as always). Greetings from UAE ;)

Nicely done, my fellow military retiree. Appreciate your guidance and tips!

I have the same gmrs and I love it

Use 3M adhesion promoter when using the double-sided tape. It makes a HUGE difference on how well it sticks.

Well done, will be saving this for future reference.

Cool setup. In the past, when I couldn't get through a firewall, I've gone through the floor and along the frame to the engine compartment/ battery. Use grommets and spiral wire wraps to protect the cable. Maybe not the best approach, but the floor is thinner than the firewall.

Got my GMRS license (that is nothing difficult at all as you just fill out an online form, the Feds just want their fee $$$) a while ago and passed the FCC test for my HAM license yesterday. Now if only I could get my dang BRONCO!!! I'm probably going to follow your lead and install the radios in my old Raptor in the meantime. Thanks for the video!

Nice, what timing! I have two midland units that just showed up yesterday for the Jeep’s. I’m switching from cb to gmrs 👍

Don't know if anyone else has heard anything, but here(Idaho) they are asking all ham radio operators to monitor for any transmission coming out of Tonga. Not sure who you'd report to but may be something to keep an ear out. Prayers and hope for the people there.

Nice install, Brad

Thanks for the great content HMCM!

Nicely done thanks for your information sir

Very timely! I’m struggling to decide a final position for a Yaesu 400 HAM radio and hadn’t considered the glove box. Right now I’ve been trying to use double sided tape to the side of the center console but it keeps falling off. I’m waiting on the JCR molle panels to come in to really attack the problem again. That midland integrating everything into the microphone is quite clutch

Very helpful video! Thanks!

Some handhelds have adaptors the connect them to the vehicles battery and to an external antenna, and also have handheld like the mounted ones.

Sweet install!

Great video as always. You might want to rethink the suggestion about modifying the power wire with a cigarette lighter plug, a 50-watt unit draws a ton of power. That would work for 20 watts but not 50 watts. @nd suggestion, you need a bigger USN emblem for the garage wall, Go Navy!

Hey Brad it's a timely video for me got GMRS license yesterday...

Have the Micro now... BUT upgrading to the Icom 2730A. You should look into this. It's 2m/440/GMRS/MURS. Best of both worlds! Had part is finding the right antenna vs SWRs...

Great video (as always Brad). Good overview of communication options available for going on adventures. 73 KK7BDW (Las Vegas, NV).

Love the antenna mount, it really works great for my ham antenna. Until next time.... Travel Safe.

Good timing I just got the same Midland to put in my JK

I'm using a comet ca2x4srnmo antenna with the optional spring and man is it great with my btech GMRS50x1 radio.

This install is especially important since it's going in a Bronco and will be frequently calling for help... 😂

Thanks for the video! I am going to use this when I am ready to install a radio. Great size. Unfortunately, my firewall grommet is occupied by clutch plumbing. I know of one other place though.

Nice and clean I like it.

Thanks, I am very new to this. Your video helps. Also, see your Masterchief plaque. Go Navy!

You could use the super velcro used to mount toll road transponders to windshields.

Great video. Thank you

Keep in mind that legal power output is limited based on the channel (frequency) you use. This applies to both FRS and GMRS. In GMRS some channels are for simplex (direct frequency radio-to-radio) operation and others are for repeater operation. In addition, different radio models will have different power output levels. Just about all GMRS handhelds will be limited to 5 watts or less (the same with handheld HAM radios). Hard mount (mobile) units will have more power, up to the 50 watt legal maximum. Lastly, antenna choice can have a huge effect on transmit/receive range. Generally, small stubby antennas provide little to no benefit over the built in antenna on HT (hand-held transceiver) GMRS radios, though that is not always the case. The nice thing about GMRS frequencies is they don't require really long antennas to get up to 6db gain!

My radio came with a round metal plate with 3m tape, that way the magnetic antenna would stick. Also the antenna base was a lot more small then the one you showed.

thank you for the video....

Original I was only looking into this to have a clean reliable way to talk to a spotter while backing in my camper but now I'm thinking about putting a mobile unit in the camper as well so we have a second option to communicate while someone is hiking or whatever. I've always been into radios but never wanted to go through the process of getting my ham license. This seems way more obtainable for me.

Thanks Brad... FCC site is not super intuitive but I'm going to try and get the license.

good video, thanks for not overcomplicating it like so many people do! I'm curious how the double sided tape has held up in the glovebox - also, how' the mic mount working out now that it's been a while?

Well done, thank you. 👍✌️

You have to exercise some caution when powering something that transmits through a cigarette lighter. If the radio draws more power on transmit than the lighter plug is able to handle, you risk overheating the wires that power it and potentially starting a fire. This may not be an issue with a GMRS radio that only puts out 15 watts, but if your goal is to install a 50 watt VHF/UHF ham radio or a something for HF that does 100 watts, directly to the battery, with the power cable that comes with the radio is the safest way to go.

On a metal hood I'd suggest leaving the aluminum bar out and putting the set screws directly into the hood. Makes for a better ground.

Very nice setup. My only concern is whether or not the passenger airbag could throw the control unit into the driver when deployed? Hopefully an unlikely scenario.

I'm fairly certain those antenna work off a ground plane. So the a-pillar probably won't affect much since it's using the hood as a ground plane.

Thank You

Great video Brad! You made it look so easy that I'll likely go this route very soon after I receive my 2dr 7MT Badlands!

I really like the Nite Ize Steelie mount. Nice secure mount and a strong magnet to allow you to place your device on any steel surface. Worth checking out.

Great install. I always try to seperate my radio power from my antenna wire just to make sure there is no interferance between them.

Hello: Brad covered that very well. I had a C B Radio sales and service shop for 10 years. I got a Ham License some years ago, I do not see any Ham antennas on Jeeps. In this day in time GRMS seems the way to go. I see C. B. Antennas on Jeeps and Trucks in Blue Ridge Mountains of Virginia. I do Not like mounting any antenna to back tire mount. Best location on Wrangler I think second 10 MM bolt from back under hood. I put a Star Washer under 10 MM bolt to get Ground for Antenna. Ground is most important thing for SWR. I mount all antennas with hight on drivers side away from tree limbs. His short antenna if fine on right side. Brad did a Clean install !!!! Firestck makes a great stainless steel flat mount to go under that 10 MM bolt on Wrangler. When screwing coax PL 259 ends to antenna fittings I put Vaseline on threads to help keep moisture out.

My biggest concern with putting it inside the console or glovebox would be overheating. Not to mention both of those locations are pretty well used for storage already.

I've been watching your videos for years, evolving from the JK to the JL and now a Bronco. The antenna mount used here might be "fine" but the coaxial cable leaves a ton to be desired. the RG174 loses a lot of signal, especially at higher frequencies, like UHF, which GMRS uses. CB would likely work fine in this arrangement however.

I purchased and installed this radio. I like your approach and essentially copied what you did. The issues I ran into was the radio in the glovebox lasted about two days and fell off. The same happened with the mic mount (although I installed mine above the Start button just behind the steering wheel. I am considering drilling a couple of holes in the side of the glovebox (where I tried using automotive double-sided tape) and installing a couple of small screws/nuts to secure the radio mount. Has your installation held up? PS: Great radio and I love it being installed.

Just thinking that the switches have wiring going around the glove box. You could(if the wire is properly rated) run from the battery with a fused line tie into that wire that goes near the glove box for power instead of running your own wires.

👍 good stuff

I have a question.. do you need to tune your antenna? I bought one that's about the same length as my stereo antenna. Keep up the videos man... we want more!

Amazing video. I learned a lot. Question about the antenna. Will that hit gmrs repeaters?

Great video brad as usual. I have a question on this model midland radio from your experience with the MXT275 how much range would you say you get out of it?

Brad, thank you for install video. I probably overlooked it but can you drop the link for the antenna hood mount? Thanks

I just noticed... Is that Pyromania? I can definitely see 1984. You ol' rocker, you.

GMRS is making strides. I would have opted for the new Midland MXT550 which is the same concept of mic controls, but gives you 50W out plus weather channels

Hey there. Perfect video. Waiting on the exact radio to come in. I also plan on hard wiring it. Where did you get the power wire with the inline fuse? Any certaint gauge or fuse size? Any help would be awesome, thanks.

Automotive grade heavy duty velcro works well with lighter weight radios.

Great video. Curious if there is space behind he glove box when it is opened fully to mount the base unit? I have a Bronco and didn't know the glove box even did that!

Hey Brad very informative video as usual. Wondered why you chose that particular antenna instead of a taller one that should perform better? Also I've noticed many Jeep owners mount their antennas on the front bumper. Any thoughts on that? Again thanks, I enjoy your, from the heart, enthusiasm.

Cool video, enjoyable! Are you going to do one for the Jeep as well (please)?

I used VHB tape for mine and still holding great (passenger side). I don't like drilling holes in my plastic.

I personally avoid body mounts like that. I recommend using ditch light brackets that bolt to the underside of the hood hinge and mount there OR if you have a roof rack, mount it to that to keep any potential paint damage and rust/corrosion at bay. But to each their own!

Thank you Master Chief!!! KI4ODF

One reason for wiring that radio to a switch is the fact that the USB charger on it pulls power and will charge a device even when the radio itself is off. That said, I have the older model that doesn't have split tones...don't know if the new one does the same thing.

Hey Brad! Great video! I was just wondering if the antenna and mount hold up after going thru the car wash multiple times? Thanx!

awesome new toys

First mistake is it's a Ford, nice video and great information

great video!! one thing that power cable to battery is not included with MXT275VP4 just the cigarette lighter cable? the one on Midland sight is for the MXT575…. thoughts? link for that power cable?

Nice video. Did you custom make the power/ground wire with fuses? Are did you purchase a ready made one? Looking for something already made.

3m heavy duty Velcro!!!!! Use it for my dual sport licsene plate lol

hey brad, curious if the magnet adhesive stayed stuck onto the mic? I used the same kit you did and it came unglued in about a day or so

Great video! I installed the same radio in my JLU Rubicon not too long ago. One question though you didn’t touch on was the antenna cable length. At the beginning a noticed the UHF connector on the table. Do you make the antenna cable as short as possible? My antenna cable came 6m long and had to run it back and forth under the hood in the cable tray to use it up. I was a bit disappointed in my reception on my trip out. Would be nice to see how and if you shortened it. Thanks again for your videos. Cheers, Paul