Very nicely done. Handled it like a pro. I have ringing ears when i get around those RT's....the loudest screw ever i encountered was a RTHB. I especially like how you methodically and slowly brought the current up and allowing it time to stabilize in-between. One of the my favorite videos yet.....and they've all been excellent. Love the channel
@subcoolHVAC5 ай бұрын
Thanks Jason, I had a site with RTHB chillers , the oil baffles had cracked/broken. Replaced and broke again. The noise was horrible, you couldn’t be in the room the harmonics were so bad. Neighbors would complain several blocks away. Chillers finally got replaced.
@topher86346 ай бұрын
I had the same problem back in December, the drives has a enable command fault and the tower fans were not coming on. It was a warm day here in central Georgia and they were needed, so I put them in hand and the temp plummeted overnight to the 30s. Next morning both chillers were in alarm for loss of oil and no differential refrigerant pressure. Took me 3 tries of restarting, alarming, then the "no differential refrigerant pressure" timer had to expire before it would let me restart it. 30 minutes each time. Had to get Trane out and reprogram the algorithm for bringing fans on. They had it wrong. It was only looking at one chillers condenser water temp so when it was shutdown, the water was never reaching the enable setpoint of the drive. Great video, I enjoy this type of content.
@subcoolHVAC6 ай бұрын
That’s a good call, RTHD doesn’t like cold condenser water for sure.
@douro206 ай бұрын
R134A screw chillers? Good thing they have the cooling tower drives indoors- I hate seeing those things outside where the heat will get to them.
@subcoolHVAC6 ай бұрын
Yep R134a screws, I prefer them indoors too. Thanks for the comment
@user-lq4yx1ee2t5 ай бұрын
You are awesome man I have learned a lot from your videos please keep them coming, you got my support you got my vote I will vote for you if you decide to run for presidency one day .
@subcoolHVAC5 ай бұрын
Thanks for the support 👍 think I’ll stick to HVAC
@zekenzy64865 ай бұрын
Great Video. Thank you for sharing. Have a nice weekend. I'm new to chiller.
@subcoolHVAC5 ай бұрын
You too, Thanks for watching!
@hvacrnortheastern2110Ай бұрын
Great job that surprised at they didn’t know chiller were off whole week or having problems l operate a #2 YK York 800 ton chiller we have alarm when chiller go off on an warning or any chiller pump and cooling pumps or any other problems we have the in the utility plant l guess that they doing a big project hated when they upgrade and the cause a problem due to the construction.
@subcoolHVACАй бұрын
Yeah EMS doesn’t have alarms enabled at these sites during unoccupied or occupied times, building maintenance has to check physically… Thanks for commenting 👍
@georgebrabec17495 ай бұрын
I don't know what the money spent limit was with this install, but a water temp control valve operated from the chiller commands can control the condensing temp. along with the VFD's to control feed temp. to the chillers. Also could use a tower by-pass valve that would operate when the VFD gets to 30%. I probably saud too much as I know that you are a great chiller tech. and you know what you are doing.
@subcoolHVAC5 ай бұрын
Yeah, I know. This is an older installation and unfortunately it was most likely lowest bid. Thanks for the comment 👍
@sterlingarcher466 ай бұрын
Nice one 👍 Just wondering, does the tower shut the fans off completely passed a low condenser water temperature setpoint ? Or is there some kind of low ambient proof system . Cheers mate 👍.
@subcoolHVAC6 ай бұрын
They do turn off once setpoint is achieved. Minimum speed is 20hz though when signal given to start
@sterlingarcher466 ай бұрын
@@subcoolHVAC I didn't quite understand why water temp got so low . I'm kinda slow sometimes to be fair ...
@subcoolHVAC5 ай бұрын
Ambient temperature had dropped into the 40’s which doesn’t happen often here causing the drop. Thanks for the questions!
@ccthepope6 ай бұрын
Wow, yo smart man!
@subcoolHVAC6 ай бұрын
😎Just a guy that shows up to work. You’re faithful 👍
@joeyoung28346 ай бұрын
Do they not have any economizers for the ahus?
@subcoolHVAC6 ай бұрын
Precoolers being installed with new ahus
@garbo89626 ай бұрын
See they have both ABB & Danfoss VFD'S. Good luck with snob nogoodnic ABB tech support. They always gave me the fifth degree when I contacted them. Took me 5 E mails & ten days for ABB to finally tell me how to locate the DC Buss voltage off the touch screen. Asked me no interrogated me why the need to know that. Da have to put it on PM form & use it to trouble shoot. If you have over 655 volts DC Buss voltage on a three phase 480 volt drive then all three line fuses are good and line voltage is not low. Contractor that installed over 50 POS ABB drives kept the manuals. Danfoss tech support never let me down. Wonder what guys think of JCI chiller drives that on our 100HP units used cold water to keep drive from getting too hot. They cut corners by using flimsy plastic water hose fittings for cold water right over the drives. Guess during water leaking would blow up the 480 volt drives.
@subcoolHVAC6 ай бұрын
I think Danfoss Is ABB also
@isaiahsmith19336 ай бұрын
Are the drives off the chiller or the BAS?
@subcoolHVAC6 ай бұрын
Independent off the T775 Tstat.
@marcobeltrandiaz3954Ай бұрын
Los of oil at compresor, do You know what is the cause?
@subcoolHVACАй бұрын
Here it was oil had migrated to condenser with low ambient conditions