Transmission Doesn't Shift (P0722 - output speed sensor fault)

Рет қаралды 272,849

5 жыл бұрын

2010 Hyundai Elantra P0722 Output Speed Sensor Circuit No Signal, P0077 Intake Valve Control Solenoid High (B1)
In this video we will be troubleshooting both of these codes
ScannerDanner Tools:
www.scannerdanner.com/tools.html
www.amazon.com/shop/scannerda...
For more information on this topic, I have written a “field manual” called Engine Performance Diagnostics which is available at www.scannerdanner.com as an eBook or paper book.
Want even more diagnostic training? Whether you are a DIY trying to fix your own car, someone looking to become an auto technician, or a current auto technician that wants to get more into diagnostics, subscribe to ScannerDanner Premium www.scannerdanner.com/join-sc... There is a 14 day free trial.
On ScannerDanner Premium I will bring you right into my classroom at Rosedale Technical College. You will find page for page lectures taken right from my book as well as exclusive classroom type case studies. What is so special about these classroom case studies? I pull live problem vehicles directly into my classroom and we troubleshoot them in real time, using and applying the theory and testing procedures we learn during the classroom lectures. There is no better on-line training of how to troubleshoot automotive electrical and electronics systems anywhere!
Disclaimer:
Due to factors beyond the control of ScannerDanner LLC, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. ScannerDanner LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. ScannerDanner LLC recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of ScannerDanner LLC, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not ScannerDanner LLC.

Пікірлер: 269

@willispower9493 5 жыл бұрын

Just wanted to comment on something you said in another video about people making comments about your boy doing camera work. Personally I think he does a good job and I think the time you are spending with him is priceless. I wish I would have had that when I was his age but unfortunately that wasn’t the case. So I was self taught early on and formally trained later. I have over 40 years doing automotive, plant maintenance and aircraft. But I can assure you that I have taught my boy just as you are doing with yours and that is what really matters at the end of the day. It’s all about giving your kids the opportunity to be better then we ever were.

@Airman.. 5 жыл бұрын

Matter of fact many FSM calls for the same adhesive lined crimp-type butt connectors instead of soldering! Glad to see you here SD

@rsanchez9192 5 жыл бұрын

Scannerdanner you are very inspirational on those tough problems. I hear your voice constantly when running down tough problems. Thank you very much.

@87shaneOmac 5 жыл бұрын

More transmission diagnostic please!!!!

@wes11bravo 4 жыл бұрын

Definitely! Especially on the NAG1/722.6 used in my POS '07 Jeep Commander!

@kbillygun 4 жыл бұрын

I have Nissan Tiida TRD automotic. And when I put in reverse and drive it shake ehe whole engine and switch off.

@ljchrzan 5 жыл бұрын

I have been in automotive for 15 years but I swear Pete's garage gets all the problems on a regular basis that I have only run into a couple times.

@Thefox2000unit 5 жыл бұрын

Excellent video as usual, and please don't remove the parts with the mistakes. Real world stuff is what it's all about. A series on the OBD modes would be VERY much appreciated. N/W Scotland

@MrFreddywise1 5 жыл бұрын

@ScannerDanner very surprised the amount of damage that i'm Assuming is caused by rats etc there, an how many people might get ripped off in taking their cars to a Garage thinking the issues that they have are a lot worse than they really are... between you an Eric O of South Main Auto Repair LLC I for one am glad to see Mechanics an Diagnostic personnel such as yourself An Eric being so open an honest to people an go out of your way to save your customers money in the Process a+ from me guy keep up the good work cheers

@jpol3808 5 жыл бұрын

And remember this folks. IF SCANNER DANNER CAN DO IT,,, SO CAN YOU!

@VoltageDropDiagnostics 5 жыл бұрын

Another great video Paul! Thanks for all that you do for the industry!

@mattbickford2640 5 жыл бұрын

13:17 caleb, thanks for the bonus footage, was waiting for "your the genius car doctor dad, thought you were about to teach me something" lol, thanks for all you guys do!

@brianmason1414 5 жыл бұрын

Awesome video as always!!! Always great to see the father and son spending the learning time together...keep it up....NO GREATER GIFT!!! ;) ;)

@antthecat147 5 жыл бұрын

did smile at the 'no comms' situation, im sure most techs have had similar brain farts in the past (i definitely have), but another great video. enjoy watching these.

@kirkabrahamson1148 5 жыл бұрын

Your videos have really improved since having Caleb as your cameraman. Not that there was a problem before, they are now just on another level.

@ScannerDanner 5 жыл бұрын

I agree, having a moving camera (as long as it's not too much) is a great thing!

@petercrispin2129 5 жыл бұрын

Have a Happy Easter Paul, 'camera man' Caleb, Dan' fam, Pete, Rosedale Tech College, and everyone else, from Down Under. I woulda loved to hear the -beeps-. Thank you for everything. May God bless you all. Hooroo for now.

@SmittySmithsonite 5 жыл бұрын

HAHAHA! You sounded just like me today (and every day, if I'm honest, lol) - I was trying to extract an oil pump from a '02 VW Passat 1.8T - saw the chain tensioner and assumed if I removed tension from the chain, I could just walk it off the sprocket. NOPE! Not happening! I lit up the shop with a fury of expletives, lol (they're probably still speeding through space, smashing asteroids along the way), and it still didn't come off! KZfaq to the rescue - turns out there was a bolt hiding in the bronze/black stained sprocket. It looked press-fit to me! Guess I should've slowed down and looked at the new one, LOL. After I removed the sprocket, piece o' cake ... of course after I got the D-shaped shaft to line up with the D-shaped hole in the sprocket. The life of a tech! 😁😉 I need to figure out how to edit my vids like that - I haven't found the "beep" sound effect yet. Could just be my crappy editing software (the free stuff that comes with the iMac). I've had to dump whole segments because of my potty mouth, lol. Gotta love rodents! My cats do, too, lol! Got 2 little ones now (8 mos. old) that absolutely destroy or eat anything that moves, HAHAHA! They're a barrel of fun. They were just walking on the rafters in my TV room as I watched your vid, knocking over all my classic beer cans ... and now they're both crashed out cold on the floor, lol. We had 5 for a while, but we're down to 4 again, after the 16 (or older - we don't know for sure) year old passed in February. She held on 2.5 years longer than expected, so that was a blessing. Great stuff as always, Paul! Hey, are you going to Super Saturday in October? I'm fairly certain I can make it to that one - would love to finally meet you in person. It's on my wife's birthday, but she'll be working. I'll just have to be super sweet when I get home. 😁 Anyway, you and your family have yourselves a HAPPY EASTER. May God bless & protect all of you. Hope your mom is hanging in there alright - we're all praying for her.

@jacquesdaoud4263 5 жыл бұрын

welcome back Caleb we miss you last video

@john7017 5 жыл бұрын

Great Video! I had the same problem last year on my Taurus when squirrels chewed wiring, hoses, and A/C ducts, even bit a hole in the evaporator coil.

@hassandallal6314 5 жыл бұрын

Learning a lot from u thanks for all ur uploads and hard work and I hope that ur son continues on ur foot steps grate job man

@Vancouver144 3 жыл бұрын

It is always fun watching you work. Good job.

@icemule 5 жыл бұрын

I've heard of you from other youtubers, but this was the first video I watched, glad you didn't edit out the mess up with the computer, hell we have all forgotten to attach something at one time or another, made the video more realistic AND funny at the same time, got me to subscribe. THX!

@ScannerDanner 5 жыл бұрын

Thank you! Look forward to hearing more form you

@icemule 5 жыл бұрын

@@ScannerDanner Wow, thxs for responding, been watching your videos all morning, very good AND entertaining, love the teaching angle and thinking of joining your premium channel which I haven't even gone over to yet, but most probably will join. I'm not a parts thrower, but also not a mechanic, but have been working on cars since 15, 55 now. Never too old to learn I say. Nothing more satisfying than fixing your own car AND saving money. Again, thx for responding.

@heyitschinoable 5 жыл бұрын

Well done! I had a VW Bug come in today for oil sensor warning light. A rat chewed through the 3 wires.

@weldingjunkie 5 жыл бұрын

Awesome video “Dan” 😂 . I love Mitchell diagrams def worth the $135 bucks. Glad you’re sons back for the holiday... thanks for sharing Paul.... Happy Easter...Jay

@nicknicu1787 5 жыл бұрын

Those little buggers! Thanks for the video Paul! 👍

@daleturnley5882 5 жыл бұрын

Great to see Caleb back. Nice video.

@deespasojevic3013 5 жыл бұрын

You are so mechanically smart Im so envious of your brain Mr Danner

@kingbolen_official 5 жыл бұрын

Nice video Paul,thanks for you work!

@swfloridacarguy1987 5 жыл бұрын

Way to go Paul, fantastic vlog as usual...

@chass5438 Жыл бұрын

I just wanna cry watching this Guy. Anywhere I take my car to the place I trust, it's always "Computer Problem !" Try changing the Computer ! No, That's Not How You Do It ! Nobody seems to be able to Diagnose, It's always, Change Parts ! Whatta Ya Do ?!

@daviddasilva4897 5 жыл бұрын

Nice video Paul,great camera work and editing Caleb,continue the great work

@fire7765 5 жыл бұрын

Great video,thx for sharing. Happy Easter.

@patrickliverpool6487 Жыл бұрын

Great job Paul your video on trouble shooting. I will always be in contact with your classes

@elaineevander 5 жыл бұрын

Great video ,Miguel from Puerto Rico best technitian hats off

@arbez.nation 5 жыл бұрын

Look, A real cameraman. Welcome back.

@realsteeltrailers1 5 жыл бұрын

Paul, love your work man! Your instructional videos have been immensely helpful in making me a more thorough tech. I thought i heard yoh say at one point that you're never supposed to unplug or plug in a com/ecm with the battery hooked up or key on? Keep up the great videos please!

@ScannerDanner 5 жыл бұрын

just make sure the key is off, disconnecting the battery is not necessary even though that is what the manufactures want

@stationaryenginesworldwide 4 жыл бұрын

Good stuff Paul ...Awesome work Cameraman

@tonistarks2874 Жыл бұрын

12:47🤣🤣know that feeling to well in the shop after awhile on a car diagnosing it

@kellyspeppers 5 жыл бұрын

Paul, you need to get a Klein Tools 1000 Multi-Purpose 6-in-1 stripper - Crimping tool. Been using the #1000 for 45 years, can't go wrong with Klein tools. The crimper will not cut into the butt splice insulation and it is much easier to get the wire and connector into the front end of the tool.

@rocketcharger17 3 жыл бұрын

Dan My car ran great after the oem purge install I grabbed two from junk yard Cleaned them up Both work Ran good for a couple days And then check engine light evap code again Went to replace with second one And started car no codes after car sitting for two days 😆😆

@miriamvivo4279 5 жыл бұрын

Wish you were closer. Gave up on subie sti emissions car from hell. Spent 1500 so far. Another 1000 replacing pcm and reprograming on the way. Anyway best wishes to you and all cleared po448 po442 po456 now have po447

@InsideOfMyOwnMind 5 жыл бұрын

Nice to know he's got it in him. One of us after all.😎

@Pablo_Automotive 5 жыл бұрын

Great work again team Danner👌🔧

@robertmedina6875 5 жыл бұрын

HAPPY EASTER ! PAUL & FAMILY!!HAVE A BLESSED DAY!!! Caleb it's a pain in the b*** to crimp those connectors!! Good video guys! Thank you for all the great videos!!

@Jpilgrim30 5 жыл бұрын

You can also buy those heat shrink crimp connectors on Amazon in a jar of like 100-200. The E-volt brand are of good quality and are the ones I usually get.

@theadventuresofjavier8698 5 жыл бұрын

Happy Easter to the Danner family and viewers

@wysetech2000 5 жыл бұрын

Well done as always.

@localfreight4222 5 жыл бұрын

That was an easy one thank you for your videos

@rsanchez9192 5 жыл бұрын

Love that super white light. Interesting how many problems aren’t found due to weak lighting.

@georgebonney90 5 жыл бұрын

Thx mr danner and Caleb 👍

@markferraro5250 5 жыл бұрын

great job SD and Caleb

@SushiPac 5 жыл бұрын

Nice work!!! Love the videos

@Karfix 5 жыл бұрын

Great job man!

@slimeslimgamerz3043 5 жыл бұрын

I USE SHRINK, SEAL AND SOLDER BUTT CONNECTORS FROM; DEL-CITY ELECTRIC BUY BULK THEY ARE FAST AND ACCURATE AND THE PRICE ISN'T TO BAD. THANKS TEACHER

@8power0 5 жыл бұрын

MISTER DANNER THANKS FOR THE VIDEO , I UNDERSTAND THANKS TO YOU TCM LIMP HOME MODE NOW WOULD IT BE TO MUCH TO ASK TO SEE THE CAUSES OF ENGINE LIMP HOME MODE AND HOW TO RECOGNIZE AND ESCAPE FROM IT THANKS SO MUCH AND LOOKING FORWARD TO THE NEXT ONE !

@bryanc2174 5 жыл бұрын

Awesome work you contribute so much. Does the shop owner not even open the hoods of these vehicles?

@johnr423 5 жыл бұрын

Good video Paul !

@pakautomotivetp411 5 жыл бұрын

I love the way u didn't remove the vdeo part in which u did mistake

@cris9835 3 ай бұрын

Hey Dan again as always I appreciate your knowledge and your videos. But most importantly I just thought I'd share something else that I really love is the fact that your brother is right there and the communication and example y'all are setting is.. well... Well.. hell..the truth it's just.. beautiful... You know I've got a lot of brothers.. But back to you guys.. y'all are not trying to out do one another just sharpening one another.. the way it's meant to be.. yeah that's all I've got to say. LOL Cris Lopez lll San Antonio Texas

@ScannerDanner 3 ай бұрын

Thank you so much for this comment. My brother means the world to me. Oh and my name is Paul Danner btw. My brother is James Danner, but we all call him "Danner". There were 4 Jim's in the same circle of friends as kids so all the Jim's got last names and even my mom calls him "Danner" now lol

@tashfeenazharjavaid5264 5 жыл бұрын

An interesting and informative video you done and you work on update model thanks

@paulfiebke3909 3 жыл бұрын

Loved this one hope you jad a Mary Christmas most of all a happy New Year's

@serafinnieves9247 4 жыл бұрын

Really great information,thanks bro.

@paulfiebke3909 3 жыл бұрын

Hope you jad the best Christmas ever, happy New Year's and keep yo the good work

@brotherbrian1 5 жыл бұрын

Danner, I've never heard you swear so much. You're finally a real mechanic.

@ScannerDanner 5 жыл бұрын

:-( I just usually edit them out

@fascistpedant758 5 жыл бұрын

I'm tired of those connectors. I don't trust them unless I crimp hard enough to damage the heat shrink and I end up putting liquid tape over them. Soldering older wires can be a pita too. I'm going back to uninsulated crimp connectors and a good heat shrink over them. It makes a smaller, cleaner joint too. If you don't have the heat shrink with sealer, you could coat the joint with something before sliding the tube over it. Back when there was more space to get up there, cats used to climb up to sleep on warm engines. They caused a different kind of damage when they were pulled through the belts and pulleys if they were too close when the engine was started.

@johnhnetkovsky8917 5 жыл бұрын

Best part----cussin at computer because it wasn't plugged in! Fn funny haha

@easyg7115 5 жыл бұрын

Do more transmission video s

@khaniftikhar9225 4 жыл бұрын

Very informative video thanks

@Watchyn_Yarwood 5 жыл бұрын

100% agree on the adhesive shrink wrap. I learned the hard way years ago. Also, that is quite a work light. I am not sure I found it in your tool listing. Could you give some more detail on it? Us old folks need all the light we can get!

@ScannerDanner 5 жыл бұрын

It's on my Amazon affiliate page www.amazon.com/shop/scannerdanner specifically it is this light www.amazon.com/dp/B01JBNS2NI/?cv_ct_id=amzn1.idea.3JYIE5R5YCLL4&cv_ct_pg=storefront&cv_ct_wn=aip-storefront&ref=exp_cov_scannerdanner_lv_dp_vv_d Thank you!

@laragreene8328 4 жыл бұрын

Seems youre a good mechanic!! I live in a small town....and there are plenty of bad auto mechanics.....you'd think they'd quit screwing up.....because the word spreads fast!! 😉

@ScannerDanner 4 жыл бұрын

Finding a good mechanic is like finding a good doctor. They are few and far between

@alexdashevsky2180 5 жыл бұрын

Great video. I have 2001 Elantra with 50k recommend to install original sensors. Not after market. Install my self after market in and out transmission sensors got problem . Purchase online original forgot all issue.

@mikeeustice4452 5 жыл бұрын

Nice video danner Honda sells what they call rodent tape . It has rodent poison in it. You can find the part number listed in one of their tsb .they recommend using it where rodents have chewed harnesses. Happy easter

@malcolmyoung7866 5 жыл бұрын

Make sure you wear gloves when applying it...

@feeneysmechanical6215 5 жыл бұрын

Find the test light from craftsman with the threaded end for a alligator clip. Works great for clipping onto wires

@babasani2 5 жыл бұрын

Really enjoyed

@revh7478 Жыл бұрын

Awesome video very informative!!! Thank you sir!!!

@karllued 5 жыл бұрын

I was working on my son's car. Soldered and heat shrink on the fuel pump, butt splice connectors on wiring near the front bumper, where an unsecured body panel broke 2 wires. Butt splices add length to wiring if needed. The fuel pump had extra wiring due to a different connector with a pigtail.

@user-io3hw7hx7q 5 жыл бұрын

Awesome outstanding job thanks good morning good luck today

@benjaminlevi7792 5 жыл бұрын

Great video thanks

@ceomom8 3 жыл бұрын

I need this man!😂

@mashamambea5704 5 жыл бұрын

yo caleb best camera man in the planet.

@abdullbasitosman5070 5 жыл бұрын

in 2007 hyundai avante 1.6 the fault code p0755 shift solenoid valve B is a common on this model , it is not the valve but it is the harness connector of the valves .

@arthurfricchione8119 5 жыл бұрын

Informative video Paul and Caleb. Happy Easter ❤️

@dydxgarage3991 2 жыл бұрын

Awesome! thanks Paul😇

@throttlebottle5906 5 жыл бұрын

lmao at trying to test it with ECM unplugged, great blooper and I hate when I do things like that... :))

@BehzadEghtesad 2 жыл бұрын

you explaining fine. tnx

@tomdewey9907 5 жыл бұрын

Solder splicing wires is still a better quality repair (if there is enough wire length to slide down a piece of adhesive lined heat shrink tubing). Crimping can damage the wire(s) as you show.

@fredflintstone8048 5 жыл бұрын

... also the quality of the soldered joint is a large factor.. a cold solder joint is far worse than a crimp connection. It's true that too much pressure in the crimp connection can damage the wire. It's about having the right feel. Personally I'm not a big fan of those solder butt splices that have the ring of solder that you heat from the outside of the tube with a small flame, or other heat source. I prefer to flow the solder into the joint myself where I can control it, and see it better. getting the proper amount of flux into the joint is critical.

@theautomotivedoctormr.wils9217 5 жыл бұрын

Good video , get a lot rodent damage also . Almost seems seasonal , certainly see influx around the fall .

@fascistpedant758 5 жыл бұрын

The worst cases I've seen are on cars stored in a garage over winter. Free food and shelter over the winter months sounds good to me too.

@mikechiodetti6737 5 жыл бұрын

Rodent damage. Have seen some of that. Can't blame anyone but the guy working on the vehicle. Not the camera guy or the shop owner, when the "tech" leaves the computer disconnected, like Ivan left the ign switch off trying to check for codes! !

@rsanchez9192 5 жыл бұрын

Hate inside crimpers, they always seem to pull wire out of butt connector. Love outside crimpers.

@abdalqadr1 2 жыл бұрын

Greetings for you from Iraq

@cluek9780 5 жыл бұрын

Been awhile since I saw more than your hands, Paul- you started lifting weight in the past year? Ha Great vid!

@joachimjohan1215 5 жыл бұрын

SWEEETTT just what i need !!!!

@h.a.dwhips4930 4 жыл бұрын

Good job👌👌👍👍

@hassandallal6314 5 жыл бұрын

U r a master danner

@jabsage155 4 жыл бұрын

thank you Sir

@joseespinoza-on8ve 5 жыл бұрын

hello from texas.

@GRUSSNewton 5 жыл бұрын

Fantastic stuff guys! The engine ECU sat on top of the engine was gold... you could almost see it laughing at you! Happy Easter!

@saurabhsharma-ts6ky 5 жыл бұрын

I love you Danner😍😍😍😍😘😘😘😘😘😘

@curlymyhero 5 жыл бұрын

I'm really kinda shocked that those chewed up and grounded out wires didn't fuck up the computer somehow... OK Scanner sed these were output wires but on computer modules everything's in a loop!

@georgebonney90 5 жыл бұрын

When you're getting results u don't expect curse the scan tool and blame the cameraman