Transmission oil/ Gearbox fluid change on 2010 Mazda 6 GH

Рет қаралды 2,348

4 ай бұрын

Today I will do a 75w-80 GL-4 gear oil change on my (2010 Mazda 6 GH) 6-speed manual gearbox.
Sludgy surprise included.
Gear oil link: www.ebay.co.uk/itm/111894120349
Disclaimer:
Due to factors beyond the control of Klavs, I cannot guarantee against improper use or unauthorized modifications of this information. Klavs assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. I, Klavs recommend safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Klavs, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Klavs.

Пікірлер: 18

@wesleys94 3 ай бұрын

Hello mate...I live in London and just bought a Mazda 6 2010 ts.... Ill watch all of your videos from now on.

@KlavsX_ 3 ай бұрын

Hello mate. Have fun with the car. Hope it is in better shape than my one 😅

@adriancernat4372 4 ай бұрын

Amazing work. Still waiting for the speed limiter warning in the dashbord video 😝😊

@KlavsX_ 4 ай бұрын

👍 Thank you. Speed limiter reminder might not be a video I and do. My car doesn't have that option.

@xlev6 4 ай бұрын

If its 4 cyl 2.0/2.5 5At speed automatic I use luqi moly atf toptec 1200G (1200 is red / 1200G is yellow) Change with filter 4 liters. Drain the old oil , take carter out , clean the gear , then put new filter on and use gasket gun to put the substance around then put carter and finish. Wait 3 hours until its well then put 3.5 liters Start car wait until it heat 10-15 minutes (to oil move in gear well) then have hand brake up And like (p-R) 10 times every time you have your foot up little from brake to make car like it move and brake again to change gear Then (r-n) 10 (N-D) 10 (D-m)10 (M1-m1)10 (M-d)10 (D-n)10 (N-R)10 (R-p)10 times Now turn engine off Add 0.5 litre Then 4 litres is totally in Start car and ready to drive

@KlavsX_ 4 ай бұрын

👍👌👏👏👏

@tonnibusa3519 4 ай бұрын

Did you do the chassis maintenance?I have Mazda 6 GH 2012 and looks very bad rust everywhere.You know where they do chassis maintenance?Thank you for your reply

@KlavsX_ 4 ай бұрын

It all depends how rusty it is. IF it's surface rust then wire cleaning it off and undercoating or wax will do. For worse case, you will need a body shop / restauration garages, where they fix all that. But If your subframe is rusted that can be replaced fully. I'm in process of making videos on how to do the undercoating

@novetrna 2 ай бұрын

What was the mileage before you changed oil? Iam doing this every 60.000 km and never had this black sludge.

@KlavsX_ 2 ай бұрын

around 200050 miles. You are correct, 60k km is the best time to change it, if you want to make sure your transmission is happy. For me this car is '' new'' to me, so I have no idea when was the last service, could have been 100000 miles ago, I got no clue.

@dragobalboa7531 3 ай бұрын

Thank you very much for the detailed instructions. I want to do the same thing on my Mazda 6 2.0 MZR. Can you describe the central jack points to me? Where exactly are they at the front and back?

@KlavsX_ 3 ай бұрын

Right in the middle of the car, it's the only metal bit sticking out from the plastic surroundings. It will be a visible hump. . At the back usually it would be your trailer hitch, if you car has it.

@dragobalboa7531 3 ай бұрын

@@KlavsX_ OK, the front would be clear. But i don't have a trailer hitch. I couldn't find any documentation about the jacking points anywhere.

@KlavsX_ 3 ай бұрын

Then you need to jack up from your subframe mounting so you can put jack stand under it's designated location ( in front of the rear wheel should be a flat metal piece with a big bolt in the middle that's screwed into the cars body. But I need to double check that, If it's strong enough