No video
📻 Transplant operation on KENWOOD (TRIO) R-1000. / MSM5524 failure support
Рет қаралды 2,883
4 жыл бұрынThis receiver cannot display frequencies. The cause is that the LSI part of the display circuit is out of order. And I cannot buy this LSI Oki MSM5524RS. Therefore, I transplanted a commercially available small frequency counter. See the link below for related videos.
🌈Repair of the KENWOOD(TRIO) R -1000
• Repair of the KENWOOD(...
🎰 an external frequency counter to the R-1000/KENWOOD (TRIO)
• 🎰 an external frequenc...
+--------+
At first I thought it wouldn't come back. However, this retro radio survived surgery and revived.
Thanks for watching and Take care. 🌈📻🌸
+--------+
P.S. 1
This replacement frequency counter can be purchased at the following site.
ja.aliexpress....
It may also be available on Amazon.
P.S. 2
The replacement frequency counter must be IF offset (-455 kHz)
• 🎰 an external frequenc...
P.S. 3
The power supply for this replacement frequency counter was taken from the 12 V line (There is a limiting resistance.) of the pilot lamp power supply on the power supply circuit board on the lower side of the main body.
+-----+
If you do this, it is at your own risk.73!🌈📻🌸
#MSM5524
#R1000
#TRIO
@broadcast-monitor508 4 жыл бұрын
Dear Tengu, you are really a technic genius, a star ! Hundred Times "Thumbs up" !!!! thank you from BM
@Ken.s_BCL-LogVideo 4 жыл бұрын
Hello thank you. I am happy to be successful. The size of this part is just enough to give the illusion that it was developed as a repair part for the R-1000.73s Tengu🌈📻🌸
@erickantoniomontalvo2612 11 ай бұрын
Excellent.
@Ken.s_BCL-LogVideo 11 ай бұрын
Thanks for the message.73s!
@TheMajkla 4 жыл бұрын
Congratulations my friend on successfully transplanting the indicator. You had your improvised external display working fine but now everything is much neater. 73, Ron 👍📻📟🧰🌈
@Ken.s_BCL-LogVideo 4 жыл бұрын
Hello, dear Ron. Thank you very much. When I was worried, I knew I should do it first.73s Tengu(^^)v🌈📻🐦🗻🎄
@MrBrian8749 4 жыл бұрын
Lots of parts to remove..but the end result was good. I accually like the new look of the frequency counter better then the old one. Nice work Mr. Tengu. 73s
@Ken.s_BCL-LogVideo 4 жыл бұрын
Hello, dear Brian. Thank you for watching. I was very worried if it would work because I removed many parts carelessly. The new frequency counter is a liquid crystal, so I think it generates less noise than a fluorescent display tube.73s Tengu🌈📻
@user-bd7jz3ti5j 4 жыл бұрын
おおおっっー、、けっこう上手く装着できるんですねっー、、なんか凄いっ！
@Ken.s_BCL-LogVideo 4 жыл бұрын
はい、おおーいま地震です。 はい、素人改造で、なんとかかんとか無理やり組み込みました。このラジオにこのカウンターを組み込んだのは多分世界初かな。自宅待機超ヒマーの作品ですね。
@user-bd7jz3ti5j 4 жыл бұрын
@@Ken.s_BCL-LogVideo うははは、で、地震ですくわ、、確かに、そちらはよく揺れますよねーw 西日本はほとんど揺れないので、就職で上京した時は、たまげますたw
@JoanEA-SWL 4 жыл бұрын
Great work dear friend Tengu, great work!
@Ken.s_BCL-LogVideo 4 жыл бұрын
Thank you sir! 73,Tengu🌈📻🌸
@rayneeny 4 жыл бұрын
wow what an excellent job you did with the frequency counter.73.
@Ken.s_BCL-LogVideo 4 жыл бұрын
Hello, Mr. Ray. Thank you very much. Yes, it became the only R -1000 in the world.73s Tengu🌈📻
@dxonda7089 4 жыл бұрын
Trabajo de profesional, nadie diría que no es el original. 73.
@Ken.s_BCL-LogVideo 4 жыл бұрын
Hello, dear onda. I really like the original. But there is no help for it.73s Tengu🌈📻
@swlminervaowl3539 4 жыл бұрын
周波数カウンターのアイディア、いいですね！IFから信号が取れればまだまだ使えそうですね。R-1000ですがVFO方式なのでまだ直せば使えるとなればサブ受信機で欲しくなる。
@Ken.s_BCL-LogVideo 4 жыл бұрын
こんばんは。ありがとうございます。出たところ勝負で何とかサマになりました。基本はアナログＶＦＯ機なのでPLLノイズが少なそうです。あとやはり音が良いです。これだけは他のラジオとは相当違います。不思議ですが内蔵スピーカーの方が音が良いです。
@GT40675 Жыл бұрын
Found all information thanks Hi, very good job, where did you take the input for this new counter ?
@Ken.s_BCL-LogVideo Жыл бұрын
hello. Please refer to the link. kzfaq.info/get/bejne/gcV8rchiyMWwg2Q.html thank you for the message.73s!
@bcloyaji 4 жыл бұрын
kurama10gooさん、おはようございます。連休はいかがお過ごしでしょうか？R-1000の周波数ディスプレイ交換作業の紹介ビデオ拝見しました。いや～、素晴らしいですね。私もその技術力が欲しいです。私もR-1000を持っていたのですが、長年放置していたらスイッチが壊れてしまい売却してしまいました。また欲しいリグではありましたが、FROGを手に入れましたので止めておきます。
@Ken.s_BCL-LogVideo 4 жыл бұрын
こんにちは、ご覧いただきありがとうございます。ステイホームのGW連休は四畳半の部屋で日々紋々としております。昨日から結構強烈なEsが出ているようです、これ唯一の救いですね。R-1000はオクで安かったので適当に入札したところ何とそのまま落札されました。でディスプレイの不治の病を後から知って相当焦りました。しかし噂どおり音が良いので何とかしたいとダメ元で交換作業しました。私は文系なので素人技の我流動画です。FRG-7も欲しいのですが流石にもう置けません。予約中のリグもそのうち来るので、いくつか処分を考えてます。
@basspig 2 жыл бұрын
The sample rate of new counter is slow and doesn't keep up as well as the original, but it's a way to safe this old receiver.
@Ken.s_BCL-LogVideo 2 жыл бұрын
Hello, thank you for your message. As you said, the display is a little slow. However, if set, it can display up to 100Hz. Have a nice DX.73s.
@basspig 2 жыл бұрын
@@Ken.s_BCL-LogVideo only need 4 digits resolution, so the faster the display can track, the better, naturally.
@Ken.s_BCL-LogVideo 2 жыл бұрын
@@basspig Hello. As you said, the faster the display response, the better. I would like to exchange it if I can get it for $ 10. thank you for the message.
@basspig 2 жыл бұрын
@@Ken.s_BCL-LogVideo I may need to do something like this with my R1000. The display sometimes blinks off and on. It mostly works, but perhaps the IC is going bad.
@Ken.s_BCL-LogVideo 2 жыл бұрын
@@basspig Hello. That's a problem. A 3-terminal regulator is placed under the LSI, but the heat treatment is not good. When the temperature rises, the LST goes out of control due to heat. I think that the symptom disappears when the air is blown from the lower left of the radio with a small air cooling fan to cool the 3-terminal regulator.
@hector4064 3 жыл бұрын
Can I ask as to have you a list of parts to be removed and how to wire the new display in place to work in the way shown in the video-the powers okay its just how do you get the data to it.
@Ken.s_BCL-LogVideo 3 жыл бұрын
Hello, Thank you for comment. I'm sorry, I removed the parts around the LSI, so there is no list. Watch this video for OSC extraction points.73s!! kzfaq.info/get/bejne/gcV8rchiyMWwg2Q.html
@eduardopower5254 4 жыл бұрын
Arigato
@Ken.s_BCL-LogVideo 4 жыл бұрын
Thank you for visiting.73s Tengu🌈📻
@伊井大 4 жыл бұрын
(*´∀`p〃q〃〃〃 1300円のカウンターにとってR-1000の一部になれるのは最高の幸せ。
@Ken.s_BCL-LogVideo 4 жыл бұрын
何故かスパムコメントになってました。ありがとうございます。この方法で世界中のR-1000が救われるならとても嬉しいですね。今度は、同じLSIが入っているFRG-7700を救ってみようかなww。
@ayeyebrazov2411 7 ай бұрын
Nice work my friend✌️maybe you can help me with mine..Display completely broken on a kenwood r2000.. Replacement display unavailable in every corner of the world..Where did you take input frequency for the new display?!
@Ken.s_BCL-LogVideo 6 ай бұрын
Hello. Thanks for the message. I won't know the cause of the failure unless I actually check the actual item. If the PLL is operating normally (if there is no display but normal reception), connect the PLL circuit to the input terminal of the new frequency counter via a 0.01μF ceramic capacitor, and then use the probe to find the PLL circuit. there is. Sorry for the late reply. I hope for your good results.
@ayeyebrazov2411 6 ай бұрын
@@Ken.s_BCL-LogVideo THX my friend... I'll try..👍
@hedadahe3911 4 жыл бұрын
Well done the display replacement. Will you be so kind to tell us where you got the replacement part. I have the same issue and found the MSM5524 chip broken. 73
@Ken.s_BCL-LogVideo 4 жыл бұрын
Nice to meet you, Mr. Heda. Thank you for visiting. I've added a link to where to get the parts in the video comment. I wish you a successful surgery.73s Tengu🌈📻
@MrHajimeSaitou 3 жыл бұрын
🤔 electronic clock is not available?
@Ken.s_BCL-LogVideo 3 жыл бұрын
That's too bad. The radio clock doesn't work.73s🌝
@ivvitan 4 жыл бұрын
Mr. Tengu, why did you fully replaced frequency counter, instead of replacing just indicator lamp?
@Ken.s_BCL-LogVideo 4 жыл бұрын
Hello, Mr. ivvitan. Yes, the LSI for displaying the frequency of this radio is broken. The LSI is not manufactured. There is no stock in the world. So I ported a frequency counter. Thank you for watching.73s Tengu🌈📻
What the Meowk!
Рет қаралды 8 МЛН
Дима Масленников
Рет қаралды 4,8 МЛН
Matt Spears
Рет қаралды 1,1 МЛН