Best video I e found . No bs . Taking the time to show is the bomb way to educate without so much stress and wonder

Thank you so much for this well spoken, well organized explanation!

got me going with my revo 3.3 thank you brother. very helpful video. made 2 trips to the hobby shop after watching this video. got my revo going and fried the spur gear and had to use what they had . keep doing what youre doing sir. truly appreciated. thank you very much...

Awesome job man! Was looking for a while but everyone else just wanted to show off their machine! EXTREMELY helpful! You knew where to look, showed the facts, hell man you nailed it!!

Very informative and easy to understand. Definitely will be tunning up my car after I break in the new motor. Thank you

Ive had my Jato 3.3 for around 7 years i think, ive never had a single issue with my 3.3.. I absolutely love it!

I appreciate you taking the time to make this video I just acquired my first nitro rc car and am having trouble getting it to run properly but this video made me see it a lot more clear and now understand how to properly tune.

Very helpful video. All the info that I needed. I've just pulled my very old traxxas t maxx out of the shed and it's running poorly and cutting out alot, so this was very helpful to get me started again! 😁

Thanks for the information bro!! You are very clear and precise with your instructions and you are not shouting like some of the other vids I have seen. Spot on!! I hope to see more of your vids in the future.....PEACE!!!!

Thank you so much! Just bought a used Revo and was struggling to find this kind of practical info out. I am having every symptom you mentioned and I thought I was going crazy. Huge help!

Thank you so much for this awesome video bro . No BS and straight to the point. 🙏🙏🙏👍👍👍

thank you so much this is so much better than just the website guide!

Very, VERY informative!!! Thanks a ton! I encourage any & every nitro enthusiast to watch this from start 2 finish! 👍🥸🤙

I just want to say thank you, before this video I used to blow a glow plug every other tank which was a bummer now after this video I've ran with the same glow plug for 3 days straight 2-3 hours use everyday. This was super helpful and got my engine tuned as new. Very pleased with your video 👍

Wow thanks.... i was sitting in my garage and was giving up on tunning my jatto..Thank you

Thank you for your good camera work, in your video, I could see everything.

It is 2022 now and this really helped me get my car running good now so thank you

Yes thank you finally bringing out the old tmaxx 2.5 again time to get it tuned and couldnt remember all the old tricks thanks alot very good detailed video!!!

Nailed it. Excellent video. Thank you!

This helped big time. Thank you!

For basic tuning and understanding you hit pretty much all the key points in the head. I wanted to add that this method of tuning may not work for everyone. back before I made the switch to brushless technology on all my trucks I would tune as follows. 1. Absolutely make sure your carb slide is set per manufacturer gap, generally about the thickness of a credit card - find a paperclip or similar that is the correct diameter and set your slide with that. 2) set both needles to stock manufacturer settings which should almost always be on the rich side. 3) make some short WOT passes and get your motor warmed up. refuel if needed (keep in mind a half tank or less of fuel will start creating a leaner condition) 4) turn in an 1/8th at a time never more, you always want to try and stay on the smaller adjustments side, making a few passes in between changes (remember needle settings don't happen instantly, you need to clear loaded up fuel out if the carb). lean in until you are happy with top end performance or just until performance starts to drop off and then richen 1/16th to 1/8th of a turn. your HSN should be set! 5) make a quick WOT pass and LISTEN to the engine - it will tell you what your LSN needs to do. when the motor is winding down after you let off throttle it should idle down smooth with a very slight hang in the transition point where the LSN starts taking back over. if the hang is long then you are loading up on your LSN and need to lean a touch (1/16th until the hang is minimal), if you go straight to an idle or below an idle and then hear it catch up to a normal idle then you are a touch lean so richen up a 16th at a time until you just start to hear the hang at the transition point. at this point you should be tuned and from this point it is all about the sound your motor makes. get familiar with what it sounds like and when you hear the tone change on top adjust, if you hear the tone change on idle down adjust. Hope this helps!! good video mate :)

Great tutorial, very well spoken.. Thanks

Great video on tuning nitro carbs....anyone looking to get there nitro running good follow this video...💯👍👍

Great video. Thank you sir.

This was very helpful to me . Thank you sir

Thank you for all the info I have the 2.5 tmax your info helped me a lot the engine is running great pls keep the same detail info about the tmax thank you

Great information thx 👍🏼

Thank you so much it’s helped a lot I really appreciate this video

Excellent video. Thank you.

Thanks for the help great video!

Absolutely the best video I will second twice and third say it. If anyone is needing an Example of a good vehicle tuning here you go. Subbed

Great video I run vp 20% fuel in my revo 3.3 and 3.5 turns out on the high speed screw works great for my climate in ga 90% of the time

Very good video thank you very much

I’ve just bought myself a used Revo, I’m going to have a go at tuning, I think you explained thing excellent in this video. Thanks.

Thanks for the help I just got my engine broke in and got the idle right have to do the hsn and lsn when I get home tomarow

Great information. Thx for sharing

Thank you got my idol working now

Really helpfull

Thanks this video helped alot

Thank you for the video I've always ran electric cars and just bought a new nitro car and I was having a lot of trouble with it until I watched ur video helped a lot

Appreciate the info

Old jato ...cute

Awesome!

Great stuff, a lot of good points, very interesting. Not blah, blah, blah..

Very well explaind. I followd all the correct steps and sadly my revo still wont start anyway.

Thank you.

What's missing is higher nitro content fuel requires richer settings. Lower nitro content fuel require leaner settings in general. This is because as the nitro content goes up, the methanol (The igniter) lessens. As the nitro content goes down the methanol content gets greater. When the methanol lessens it takes more fuel/richer settings to get enough methanol to even ignite. When the methanol is plentiful less fuel is needed so leaner settings can be used. Another point is the rule of thumb is the smaller the engine the higher the nitro content can be. I run Red max 60% nitro in my 4tec 3.3cc/.20ci, engine and must run the high speed needle at 5-6 turns out and that's a lean setting for racing.

I bought my Tmaxx 3.3 recently from Traxxas and broke in the engine. Few days ago this will be use full information in the future.

Thanks

Dude your carb is cracked on jato

thank you go job i need that in fo thank you

Thank you I have the revo 3.3 and I'm trying to get it tunes and did it backwards and couldn't find how to factory reset it

Great video for a new cat like .. i mean excellent ..

THANX FOR EXPLAINING THE WEBSITE IS completely useless and you made it clear 4 x 360 deg turns bit diferent to 4 turns.thanx

Canada West coast Vancouver area and surrounding areas High oxygen on the west coast of Canada Settings need to be 4.5 turns out for optimal running for high speed needle Mabey even 4 and 3/4 turns out from closed. Low speed simple flush to throttle body NOT the throttle connector. Gap .6 to .7 mm No More At the 4 turns on the high flush on the low speed with a 1 mm gap is real high idle and still to lean on the high speed. Hope this helps anyone who reads these comments

Did you upgrade the receiver battery pack. I have the nitro rustler and was wondering about upgrading from using the regular AA batteries to 5 cell hump receiver.

Don't cut a square hole in the front window, cut a round one! Square holes make the body weaker and easily cracked or broken. Round holes do not have the same propensity for cracking as square ones!

You explained that really well thanks pal

RE: Tuning woes with REVO 3.3 The operating temps should be at 270ish, I run my engines at around 245-280 depending on the day. here the guide, I’ve just copied this from a file on my computer so sorry if there are some inconsistencies with your problems. (I’ll share this around. Cheers) now, for the idle being too high or too low, first set it back to factory which is 4 turns out on the high speed needle and 1.75 turns out on the low speed, start the truck and run it around to let it warm up, once you have it warmed up bring it in and let it idle, if it's to high you will need to turn the idle screw out maybe 1/4 or 1/8th of a turn, and see how it's idling then, if you can’t get the truck to start, give it a little bit of throttle, once the engine is warm it should start up very easily. then one you have it idling you can start tuning, when your tuning, go in very small increments at a time, and ALWAYS tune the high-speed needle first, I usually go by 1/12 or 1/16th of a turn at a time, but must guys go 1/8th of a turn, after each adjustment do a few high-speed passes, take very careful note of 3 things. 1. the performance, has it gotten better or worse? when you start getting the rpm up does it sound like it's cutting out? if it sounds like it's cutting out then you are to lean and need to richen the HSN, if it is loading up and the performance is very sluggish then it is rich and you can go a little leaner 2. the smoke trail, there should always be a nice, clearly visible trail of blue smoke coming from the exhaust, always, if you cannot see a good trail of smoke, it is another sign of being to lean, if you’ve a lot of smoke at all rpms then you can go a little leaner 3. the temperature, since this is your first nitro truck it is a good idea, you get a good, reliable temp gauge, the engine should not go over 270 degrees F, if it does it is another sign of being to lean and you should richen it up just a little bit, but something most people over look is that you should not run under 190 degrees, if you do the piston sleeve doesn't expand enough and the engine will wear out very quickly. a last note on the high-speed needle is, never tune by one symptom alone, never tune just by performance, or smoke trail or temp, use at least two, so if you lean the engine out and the temps go from 220 to 230, and you note it's a little more powerful and go a little leaner, the only time you should ever tune by using just one symptom is when: A: you run to lean and the engine start hesitating and cutting out B: the temp goes above 290 degrees F in both cases you need to richen the HSN by at least 1/8th of a turn if not more. now for tuning the low-speed needle one the high-speed needle is set to where you want it, you can start with the low speed, start off at the factory setting, and just like the HSN tune in small increments of at least 1/8th of a turn, if not smaller, when tuning the low speed, you are aiming for a nice crisp throttle response, if you run the low speed to lean you will eat through glow plugs very quickly and it can damage your engine. once you start getting close to what you think is the best throttle response, tune in smaller increments, once you get it so as soon as you touch the throttle the engine start revving up and doesn't bog down at all, so as soon as you hit the gas, the truck takes off, once you get to that point do not lean it any further, and for a safe guard i like to richen it by 1/16 of a turn. to test to see if the low-speed needle is set to rich or to lean you need to do the pinch test, all you do is pinch the fuel line, and count how many seconds it takes for the engine to die, when you pinch the fuel line, the engine should idle normally for a second or two, then just before it dies it should rev up a few hundred rpm, then die on the count of 3. if the engine dies in 2 seconds or less, or does not rev up at all, you are to lean and need to richen the low-speed needle, if the engine takes more than 3 or 4 seconds to die, you are too rich and can lean the engine out a bit more. for then engine not start, check to see if the glow plugs good, to do that just take the plug out, connect it to the blue glow wire, hold the glow plug up against the cooling head, insert the starter wand into the truck and press the red button, if the wire in the plug glows it's good, if it doesn’t you need a new plug, if the plugs good it may be because the engine is flooded, so you need to take the glow plug out, pinch the flue line, turn the truck upside down and turn it over with the start wand and see if that helps. once you have done all your tuning you might have to set the idle again, if you do just follow the steps I posted at the top of the page, you should never have to touch the idle screw unless the truck is idling high enough for the clutch to engage, or that low it won’t start.

What do you use to clean your cars, the inside looks brand new, the only reason I realised it wasn’t was when I saw the tires.

so even though it takes about 6-8 secconds to stall with the pinch test i should leave it bit rich as is to run in.ok and the tiny screw in between the carb hi and lo is the idle and to decreace it i turn counter clockwise to reduse the egar jumping?but how much is needed enough so it doesnt do it very slowly? or is it the low speen one on the blue sleve on the carb slider?

Never new about the body thing. I'm gonna cut those out because my engine would still like you said. I've also noticed that my Rustler likes to run with a very wide gap unlike my slash. Im going to set all the screws to factory and go from there to try and fix some of my problems. Of you have any tips let me know

when you turn the idle screw all the way out is the slide post to closed all the way

I'm currently trying to tune a new 3.3 I just swapped in. Wont run unless the ignitor is connected. I've ran that low needle in an out over and over. Nothing. I did not check the idle screw tho. I guess I'll try there today.

I want to do a brake upgrade on my jato I just brought it but I don’t like those brakes. I brought a brake set I wanted to put on there. Do you know how to take the star piece the brakes are sitting on off?

I have a traxxas 2.5 Tmaxx. My ? Is on the carberater below the high speed needle setting there is a small manafold it has 2 little caps on it. I have one cap missing will thT effect it from running ?

Put the cooling fan in the windshield

could i use a 1 mm allen wrench to check the carb Gap i know a 1.5 wont go in the GAP

Picked up a older nitro with a g3.0 engine what would be the basic settings for it

i flipped my tmaxx 2.5 classic and when i start it its some accelerated,and the wheels spin in different directions. any help? thanks in advance

I just got my tmaxx 2.5 im the second owner and the issue is its so hard to turn on and if does turn on it run away just a little bit and then it turned off by it self but still I didn’t try to touch the idles

Can you fit a bigger engine in a nitro bug crusher.???

You could run a cooling fan

Is this what I should do after I upgrade from 2.5 to 3.3?

Will this work for a Traxxas image .12

Good video but you forgot to mention that after a good bash you should take your glow plug out to let it cool down before you run it again I been doing this for a long time with my 1/5 scale one s an nitro trucks

Great video

My rustler is Brand New. It started just fine with the Traxxas fuel but once it was started and I started the 1st break in process the car would roll forward freely. I didn't want to touch the needles but this is very frustrating could you give me some pointers.

Is there fuel supposed to be leaking from nitro engines or no?

also how do you like that traxxas fuel?

Hi do you know why my traxxas 3.3 carb is spitting nitro fuel while running

Mine takes 7 complete 360 degree turns to stay running. It's imperfect. I had to do a lot of trial and error to get a good, non rich and especially not Lean tune. The high speed needle is Sometimes inaccurate.

what can i do tmax 3.3 carb won't idle down please help

#Mogyver69 Is the rustler with the 2.5 the same setting for factory?

I'm running a slayer pro, I got it running great but when I full throttle it & it bogs like it's too much air, is that the low or high?

my car is running almost perfect now but my pinch test stalls at about 6 secconds so i need to low speed screw in a tiny bit to lean it out and make it stall at 3 secconds i dont tough the high speed black one? i need to wear the engine in yet should i leave it a bit rich for now the exsaust cuts it off imidiately but i wanna protect my engine whyle im wearing it in for now would you advise. i will ask the other guy as well. cheers.

I see you did this video 6 years ago but not much of anything has changed. Do you have a t Maxx? On that truck it’s very easy to see can you please do a video of tuning a 2.5 or 3.3 motor please? Thank you

My traxxas 3.3 has been overheating gonna try the window for sure

This is providence, I have those same exact cars. And need help!

What’s your carb settings for the revo pls tell me your settings pls

Having some major dramas with my 3.3, the car won’t even run/start with factory settings. Needs to have a V fast idol to even tick over. It runs smoky (rich) no matter how much I lean the HSN. The LSN has to be super lean to even keep the engine running and the idol open almost 2-3mm and even with all this it runs when off the ground but always stalls when on the ground. Not a noob at RC but I’ve stripped, cleaned, resealed and checked compression. The idol is rough and just wont run. New glow plug and 20% fuel 🤦‍♂️🤦‍♂️ I’m stumped any help? I feel like I’m chasing an error and never seems to keep running smooth at all

can u post a link plz

Bro, I was having so much issues with my revo 3.3 and I followed the paper and it started and stayed running, but I kept calling traxxas support and they couldn't help me and do this..

Well 20% hurt engine after running 1 gallon of 30% I only ran it on the one and want to change too 20% what’s your advise?

Really, Just explain that the low speed need has to be horizontal to be even as per explained in the instructions.

1,5 4.30

Is aviation rc fuel good in a nitro truck?

now i thjnk where my leaks was coming from missing o rings hsn and lsn there gone so i got a new carb rebuild kit got to put them in so i can check it again

First I could not get mine to run at all so I have to check on everything

How long should a glow plug last on the 2.5 engine