Your illustration of the J hook and which trim side to remove has very helpful. Thanks!
@chuckwhite726 жыл бұрын
Thank you for the video it was a big help. Just a helpful tip, when I cut something that the wood my blow out I put a strip of masking tape down then cut it and it will stop the wood from coming up. Thank you again.
@HighRidgeHandyman5 жыл бұрын
Try painters tape on the cut. Comes out perfect. Great video 👍
@loganc42335 жыл бұрын
Thanks for the vid! I was convinced I would have to use dynamite to get my old pocket door out ...
@j.sherwoodowl48266 жыл бұрын
Great tip on the cutting technique. thanks so much!
@bobmedic32144 жыл бұрын
Use a track saw for cutting doors down. Or make a door board with some Masonite. Cuts much straighter and eliminates chip out.
@rsquared007Trini4 жыл бұрын
It would have been nice to see how the door is put back on. Its good to see if its hard or easy and how one person goes about putting it back on
@devayrcorreajr34076 жыл бұрын
Amazing explanation, Tks lot!
@bufordbox4 жыл бұрын
I score that cut with utility knife ...no chipping
@anthonyhitchings10512 жыл бұрын
I would have power-planed the hidden long edge so that its no longer tight
@smartysmarty17143 жыл бұрын
This guy is a hack. I nearly died laughing at the "cut half way through" *secret. What you do if you're a real carpenter, is you take a straight edge such as a level or drywall square, clamp them on the door where your cut is going to take place, and then score a DEEP line across the door careful to cut through the veneer all the way. Then, you remove the straight edges and cut just slightly "south" of your scored line. After the cut is made, gently corner sand both sides of the door and you will have a perfect, chip free cut every time if you follow this method.
@ManyouRisms3 жыл бұрын
You're literally the worst person, berating someone providing free information for people who have never done something before. 'Smarty smarty'.... hardly.
@lydiacarillo43942 жыл бұрын
I've been seeing everybody's pocket door I see the side where the door comes in and out but what about the right side I don't know what else to put there if the door is going to wiggle back and forth sometimes I just see a flat board you guys never show the other side where the door does not come out please show me thank you I do like your video
@skipperrichman42784 жыл бұрын
I wonder if you should trim maybe 1/16 - 1/8 off the side so as it will go back in easier?
@SSmith-fm9kg5 жыл бұрын
Thanks!
@thunderbee226 жыл бұрын
great tip, but was there a monster in the room at 2:59 ?
@americantrademasters8736 жыл бұрын
Brian Robertson sorry about that ! I should've edited that out, there was a home hospice patient coughing in the other room😳
@thunderbee226 жыл бұрын
No worries! Thanks for the video. I'm actually going to remove a pocket door and put a wall in its place. This was a good video to help me get halfway there!
@DejuanJohn5 жыл бұрын
Brian Robertson bruh I thought I was tripping
@jimjordan56305 жыл бұрын
Why in their right mind would install a floor so that a pocket door with need to be trimmed!? Thankful that this isn't a vintage door situation! That would be a real shame!
@isaiassanchez94783 жыл бұрын
Try not cutting inside a finish kitchen.nothing is protected for client
@edwardschoenman21393 жыл бұрын
The age of skilled American carpentry is mostly dead. Brute force and stupidity rule.