Tripping circuit part 2 of 132 KV SF6 circuit breaker
Пікірлер: 34
@ranglalbind73472 жыл бұрын
Nice sir
@kapilkumarbhajipale63572 жыл бұрын
Sir very helpful video, thank you
@ManishSingh-og1kd3 жыл бұрын
Dear sir U r doing a wonderful job of knowledge sharing . God bless u
@jayabikash Жыл бұрын
Awesome video
@yogeshshrivatsa55403 жыл бұрын
You explain in simple way.Thanks a lot sir.
@beingelectrical66413 жыл бұрын
Stay connected Watch all the videos and dont forget to like, share & subscribe
@abhishekchourasia10373 жыл бұрын
Nice video
@ManishKumar-mf5zzАй бұрын
Thank you sir
@AjeetKumar-iq7fp2 жыл бұрын
Thank you for clearing my doubt 🙏
@khan_tanzeem05213 жыл бұрын
Excellent just excellent 🎖
@ManishKumar-mf5zzАй бұрын
Sir, please make control panel complete series as for 132kv cb.
@ashishvitekar34743 жыл бұрын
Very well and have been so good at all
@rohtashpal78233 жыл бұрын
Thanks for sharing knowledge.
@ahsanaziz611311 ай бұрын
❤❤❤
@punamchand40593 жыл бұрын
Thanks
@sudhakar3753 жыл бұрын
Master relay per bhi video banay
@sarojiniperumalla3 жыл бұрын
Sir small doubt , when source 1 is failed k10 will not energise so we will not get pressure indications , .. does it mean B4 is deenergised so capacitor tripping works .? Or B4 is independent of K10 and works only when pressure is down? Sir please carify
@beingelectrical66413 жыл бұрын
B4 depends on actual physical pressure of gas.. The status of B4 is further reflected in K10, thus K10 is called density monitor multiplier.. K10 just multiplies / propagates the status of B4. In other words, actual gas pressure commands B4( gas density monitor) and then status of B4 controls K10. Thus K10 depends on status of B4. And B4 depends on actual gas pressure. Vice versa doesnt work here.
@anilshemade60483 жыл бұрын
@@beingelectrical6641 very well explained !Thank you.
@ranjansahu23623 жыл бұрын
So good sir... I hv one doubt.. if only dc -1 fail but gas pressure is not low... Then how capacitor current will flow to trip ckt.. plz explain sir
@beingelectrical66413 жыл бұрын
It wont... Capacitor tripping wont function
@godavarthiramadevi1410 Жыл бұрын
@@beingelectrical6641 sir, if at that time, any fault occurs and 86 relay gives positive signal, how Breaker will trip ?
@godavarthiramadevi1410 Жыл бұрын
@@beingelectrical6641 A permanent positive is connected to 86 relay, that is from DC source 1 or 2 sir? If DC 1 fails, then how 86 relay works during any fault? Please clarify sir
@channabasavaraj98173 жыл бұрын
Sir under low gas pressure, if CTD is directly giving tripping signal to coil, then breaker will trip.under low gas pressure if breaker operates, then flashover of limb will happens. Kindly resolve this sir
@beingelectrical66413 жыл бұрын
It will be interrupting normal working current which can be easily considered much lower than the fault current... Plus the moment, pressure gets lower than threshold,, tripping command gets issued to cease any further possible operation of breaker (arc interruption). SF6 pressure is essential for sufficient arc & thus heat quenching and the threshold pressure is designed accordingly...considering one time safe operation atleast
@yagnikpansuriya1267 Жыл бұрын
To source 2 ka kam kya hai ? Wo aapne nhi bataya...
@beingelectrical6641 Жыл бұрын
Source 2 generally remains for back up.. in some drawings, source 2 backs up the whole DC bus, whereas in some cases, source 2 is used only in trip ckt 2 operation..the secondary protection
@beingelectrical6641 Жыл бұрын
Pls go through other videos of the channel.. I am sure..all of your queries shall be resolved
@jayabikash Жыл бұрын
Awesome video
@beingelectrical6641 Жыл бұрын
Thanks! Keep sharing, keep loving
@AjeetKumar-iq7fp2 жыл бұрын
Thanks you sir
@md.alamgirchowdhury90843 жыл бұрын
Dear sir U r doing a wonderful job of knowledge sharing . God bless u
@beingelectrical66413 жыл бұрын
Thank you.. and please stay connected. Never forget to like the videos