Triumph Valve Seat Cutting

Рет қаралды 3,677

Жыл бұрын

Howdy!
Today Kyle is going to be cutting the intake pocket valve seat on his 1967 Triumph T90 road racer..
We will be using Ferrea valves along with the Goodson "3D Fast Cut" system
Unfortunately we will not be showing the cutting of all 4 seats, however, this video will give you an idea of what exactly goes into valve seat cutting and/or a valve job
Enjoy!
#classicbritishspares #triumph #goodson #ferrea

Пікірлер: 29

@kevinsmith1044 Жыл бұрын

How is it this young guy has all this OLD Dude knowledge.....keep up the good work

@tmackinator Жыл бұрын

I was a machinist / model maker for 40 years. I'm very impressed with your careful set up. Nice job! My only other comment is please, please wear safety glasses, you are done if you damage your eyes.

@markgriffith2531 Жыл бұрын

Outstanding! Lots I can replicate here.

@chrisstephens6673 Жыл бұрын

Well that brought back memories. 25 years retired from working in a famous British bike shop in London where I would do the valve work on triumphs. Back then just about everything was available engine wise but we made a lot of bodywork parts in house. PS hated triumph heads as the seats quickly recessed too far after a couple of valve guide changes.

@janettapp3754 Жыл бұрын

Thanks for the great demonstration.

@classicbritishspares Жыл бұрын

Thank you very much for offering great tools!

@GarySmythe Жыл бұрын

I love these videos. Keep them coming!!!

@classicbritishspares Жыл бұрын

Thanks!

@1924ab Жыл бұрын

Nice job

@georgehirvela7435 Жыл бұрын

Well done young man...

@classicbritishspares Жыл бұрын

Thank you

@stuntr1 18 сағат бұрын

Have you ever used a runout gauge and see what u get ? Interested in your runout figures. Also, where did you get your adjustable angle plate?

@classicbritishspares 18 сағат бұрын

@@stuntr1 considering that I don’t have to use lapping compound to check the contact or lap the valves, I’m going to assume it’s less than .001”. Angle plate came from eBay.

@calmanley6618 Жыл бұрын

Great work, nice setup. Safety glasses?

@classicbritishspares Жыл бұрын

Thanks - no glasses needed

@georgehirvela7435 Жыл бұрын

Can you itemize all the components you used of the Goodson "3D Fast Cut" system ?

@classicbritishspares Жыл бұрын

Maybe in a next video, thanks

@drrjim 5 ай бұрын

Nice job. Just curious how you handle that big hammered wide 45 on the exh?

@classicbritishspares 5 ай бұрын

Cut the bottom angle, and cut the top angle. Not really necessary

@drrjim 5 ай бұрын

@@classicbritishspares Just have found that sometimes you can end up with a pretty sunken seat by the time you get all trued up and all three angles in there.

@classicbritishspares 5 ай бұрын

@@drrjim exactly why I don’t do three angles. Most of the time I cut a 45, and I do the bottom angle. Other than that I leave it. Not gonna make much of a difference anyways. If the valve seat is concentric to the guide, and insert, it’s better and then you can do a three angle

@drrjim 5 ай бұрын

@@classicbritishspares Yes, often they are not concentric to the guide. Thanks for your communication. And again, good job !

@classicbritishspares 5 ай бұрын

@@drrjim thank you !