Exactly :D

ty!

Pao Yang if you buy from Denny he has a instruction paper explaining details , it was super easy just 10 mins of work.

Pao i think i'm going to that route also lol let me know how it goes for you since i'm going to wait until off season to do mine

@@TheToufue91 kzfaq.info/get/bejne/qc-DlrOW16qVnXk.html

Nope , it doesn’t. Someone told me not possible :/

I don't know. I could see using a motor to get to/from your fishing grounds and using the pedal drive to maneuver once fishing starts.

谢谢!

Thanks ;)

yes and yes :) 31"

they should come with the hobie h-crate

Obrigado! Eu peguei alguns grandes largemouth bass e rockfish até agora :)

Ken Teague I used Marinco plug and receptacle . Holes are 1-3/4” and don’t throw away the plastics you cut , you might need them later to patch your kayak. - Marinco 12VBPS3 Trolling Motor... www.amazon.com/dp/B06XGB3QNF - LENOX Tools Hole Saw with Arbor,... www.amazon.com/dp/B004YK8D8I - Marinco 12VBRS3 Trolling Motor... www.amazon.com/dp/B06XKPPGJV

Great. Thanks so much for the info.

nope , hobbie's bow is very strong , didn't need anything other then existing bolts

check this website www.onthewaterinnovations.com/

I use MinnKota quick release bracket for riptide versions.

Didn't test the XI3 but I have never had an issue with MK. I still have it, very durable, I used it in salt and fresh water with no issue. Spot lock is a great feature against wind and current.

It goes up to 4.4 mph , regular speed is around 3.9 - 4.0 at speed 10.

yes , the head unit has silicone gasket protects it from water damage , I usually clean it with spraying water and no damage so far. important note , make sure to buy saltwater unit !

I had no problem with heading lock on full speed. You just need to set the settings as a small boat , otherwise it will make sharp left&rights .

@@MustafaToramanNice! Gonna try the firmware update for the xi3 first. If it don’t work out I’ll be going over to Minn Kota.

Depends on the type. GPS trolling motors should be installed on the bow. Other basic ones can be installed near the seat so you can move them however you want.

I will make another video about the installation and parts.

Richard Chao yes , It just sticks out like 4 foot and I dont need to remove middle seats . I use 3 cam straps , one for each h rail to handles on sliding door openings and one for the hatch , I will do a video later to show how I do.

I have a 08 Toyota Sequoia and that’s how I load my kayak too

Yes, I cut mine 33" , it was 54" . Some people cut them to 27" but I prefer 6" more for saltwater use due waves.

@@MustafaToraman what kinda battery?

@@ARJ11569 AmpedOutdoor 100Ah Lifepo4

@@MustafaToraman Interested in this setup,cost if you would?

There is a written instruction to mount the bracket but overall it's very simple. You remove the handle and remove the straps from front hatch. Drill little bit bigger holes for rear mounting part and put the straps and the rest together. Only the issue I had that I needed to bend the legs to make it perfect fit (not all kayaks are perfect shape), which you should do after heating the metal to avoid paint chip. I believe you won't need a power pole , spotlock is much more better :) I'll do another video once I have time to show parts and install steps.

Mustafa Toraman thank you sir.

Spot lock is the must have for big body of water. Fish finder and other electronics are on another battery. 100ah battery is only for trolling motorz

the PA 14 360 is $4799.00. In Florida it'll run you $5136.00 after tax. just ordered mine a couple weeks ago. This dudes kayak with everything he has on it will run you roughly 9k to 10k if everything was bought brand new.

The cheapest Minn Kota with spot lock is $1600.

Definately worth more than his car :)

@@russabravanel7516 lol :))

Merhaba,videoyu begendiginize sevindim. Ne yazikki Turkiye sartlarinda cok pahali bir kano. Modeli Hobie Pro Angler 14 360 , 2020 de cikan en son model. Benden de selamlar sevgiler.

Good question. I only fish backwater (Chesapeake Bay) so I don't have offshore open water experience. The bow mount trolling motor puts some weight (35 lbs) on the bow but not that much to notice, maybe 1 or 2 " difference. I got a couple of heavy weaves (almost lost the rod in my hand) due to high-speed boats but no water went inside the hull. The gasket around the front hatch is very good and most of the time the actual source of the leak is the rod holders. I have applied silicone and fully sealed them so no water leak from them as well. In my opinion, PA14 is only good for calm weather on open water, having a bow mount is not that much of a difference. If you really want to go open water then make sure you seal the rod holders and other lower points, hatch seal is not that big of a problem in my opionion.

Also, I was thinking to design windshield-kind-of plexiglass to attach my bow to stop waves but I didn't do it since there was no water inside the hull after a couple of big waves.

Can i use that setup for salt water?

Nope, it is a Riptide (saltwater) motor but I changed the plastic parts with black ones.

Yeap! I live in NOVA :) find me on facebook!

with quick release bracket it was 1500 + 140 for Denny's bracket - www.onthewaterinnovations.com/shop

yes , to 31"

mount is from onethewaterinnovation , trolling motor is as is

I'm using 360 when I don't mount the trolling motor :)

Not tippy unless you go backwater with waves. Don't know the overall cost but it is over 10k

not sure but it is over 10k with the electronics

I bought 54" riptide then cut it to 33"

With Panoptix + Garmin 10" it's over 12k I think .

Talk with Brian , he has the best prices and service! facebook.com/BBGMarine/

It was 55 and I cut it down to 30"

yes it does and it is a life saver! super convenience!

the one I have is riptide (saltwater version with iPilot) , it was 1500 with quick release bracket

Hobie Pro Angler 14 360 2020

Kinda true but can you put your bass boat in your van or fish lakes where there is no ramp ? :) Side note , I have a bass boat too ;)

yea ... unless you go electric only or no motor lakes for fishing

No, I don't. If you have PA14 and getting water inside the hull then make sure your rod tubes are sealed. I have not had any water since I sealed them.

@@MustafaToraman thank you! Went out Friday and found out the rod tube seal was not good lol

lol :) I am surprised too!

around fairfax area , you ?

@@MustafaToraman i’m in gloucester

I have a heading sensor. It is inside the hull.

well , I did 8 miles in a day and battery was still over 50%

I bought the Riptide 54" 55lbs 12v with Autopilot (not link) and the reason for Riptide is because I go to Chesapeake Bay (salt water). My shaft length is 33".

What kind of speed do you get with that 55lbs. thrust minnkota

More than that 🤘

@@MustafaToraman 😱

been waiting for that day :)